SIST EN ISO 11296-3:2018
(Main)Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
This document, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit
lining systems used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U)
as manufactured, as well to the installed lining system with its associated joints.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-3:2018)
Dieses Dokument legt in Verbindung mit ISO 11296-1 die Anforderungen und Prüfverfahren für Close-Fit-Lining-Systeme die zur Renovierung von erdverlegten Abwasserkanälen und –leitungen verwendet werden, fest.
Es gilt sowohl für Rohre und Formstücke aus Polyethylen (PE) oder weichmacherfreiem Polyvinylchlorid (PVC-U) wie hergestellt, als auch für das installierte Lining-System mit seinen zugehörigen Verbindungen.
Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11296-3:2018)
Le présent document, conjointement à l'ISO 11296‑1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubage par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression.
Il s'applique aux tuyaux et aux raccords en polyéthylène (PE) ou en poly(chlorure de vinyle) non plastifié (PVC-U) tels que fabriqués, aussi qu'au système de tubage installé avec ses assemblages associés.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11296-3:2018)
Ta dokument skupaj s standardom ISO 11296-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme cevi, ki se uporabljajo za obnavljanje podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka. Uporablja se za cevi in fitinge, izdelane iz polietilena (PE) ali nemehčanega polivinilklorida (PVC‑U) kot so izdelani, pa tudi za nameščene tesno prilagodljive sisteme cevi z ustreznimi spoji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11296-3:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 11296-3:2011
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 3.
del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11296-3:2018)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO 11296-
3:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sans pression - Partie 3:
Tubage par tuyau continu sans espace annulaire (ISO 11296-3:2018)
Ta slovenski standard je istoveten z: EN ISO 11296-3:2018
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 11296-3:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11296-3:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 11296-3:2018
EN ISO 11296-3
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80; 93.030 Supersedes EN ISO 11296-3:2011
English Version
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks - Part 3:
Lining with close-fit pipes (ISO 11296-3:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux de branchements et de von erdverlegten drucklosen Entwässerungsnetzen
collecteurs d'assainissement enterrés sans pression - (Freispiegelleitungen) - Teil 3: Close-Fit-Lining (ISO
Partie 3: Tubage par tuyau continu sans espace 11296-3:2018)
annulaire (ISO 11296-3:2018)
This European Standard was approved by CEN on 5 August 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-3:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11296-3:2018
EN ISO 11296-3:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11296-3:2018
EN ISO 11296-3:2018 (E)
European foreword
This document (EN ISO 11296-3:2018) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards
shall be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11296-3:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11296-3:2018 has been approved by CEN as EN ISO 11296-3:2018 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11296-3:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 11296-3:2018
INTERNATIONAL ISO
STANDARD 11296-3
Second edition
2018-08
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11296-3:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 General . 2
3.2 Techniques . 2
3.3 Characteristics . 2
3.4 Materials . 2
3.5 Product stages . 2
3.6 Service conditions . 2
3.7 Joints . 3
4 Symbols and abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Materials . 3
5.1.1 General. 3
5.1.2 Distinction between PVC-U types . 3
5.1.3 Virgin material . 3
5.1.4 Reprocessable material and recyclable material . 3
5.2 General characteristics . 4
5.2.1 Appearance . 4
5.2.2 Colour . 4
5.3 Material characteristics . 4
5.4 Geometric characteristics . 5
5.5 Mechanical characteristics. 5
5.6 Physical characteristics . 5
5.7 Jointing . 5
5.8 Marking . 6
6 Fittings at the “M” stage . 6
7 Ancillary components . 6
8 Fitness for purpose of the installed lining system at the “I” stage .6
8.1 Materials . 6
8.2 General characteristics . 6
8.3 Material characteristics . 6
8.4 Geometric characteristics . 6
8.5 Mechanical characteristics. 8
8.6 Physical characteristics . 9
8.7 Additional characteristics . 9
8.8 Sampling . 9
9 Installation practice . 9
9.1 Preparatory work . 9
9.2 Storage, handling and transport of pipes and fittings . 9
9.3 Equipment . 9
9.3.1 Butt fusion equipment and debeading equipment. 9
9.3.2 Reduction equipment .10
9.3.3 Pipe skids/rollers .10
9.3.4 Winching and rod-pulling equipment .10
9.3.5 Pipe entry guides .10
9.3.6 Reforming equipment .10
9.3.7 Electrofusion equipment .10
9.3.8 Inspection equipment .11
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
9.3.9 Lifting equipment .11
9.4 Installation .11
9.5 Process-related inspection and testing .12
9.6 Lining termination .12
9.7 Reconnection to existing manholes and laterals .12
9.8 Documentation .12
9.9 Final inspection and testing .12
Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe —
Determination of memory ability .13
Bibliography .15
iv © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, Subcommittee SC 8, Rehabilitation of pipeline systems.
This second edition cancels and replaces the first edition (ISO 11296-3:2009) which has been technically
revised. It also incorporates the Corrigendum ISO 11296-3:2009/Cor 1:2011.
The main changes compared to the previous edition are as follows:
— Clauses 3, 5, 6, 8 and 9 have been technically revised;
— the previous Annex B has been deleted.
A list of all parts in the ISO 11296 series can be found on the ISO website.
© ISO 2018 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
Introduction
This document is a part of a system standard for plastics piping systems of various materials used for
renovation of existing pipelines in a specified application area. System standards for renovation dealing
with the following applications are either available or in preparation:
— ISO 11296, Plastics piping systems for renovation of underground non-pressure drainage and sewerage
networks (this series);
— ISO 11297, Plastics piping systems for renovation of underground drainage and sewerage networks
under pressure;
— ISO 11298, Plastics piping systems for renovation of underground water supply networks;
— ISO 11299, Plastics piping systems for renovation of underground gas supply networks.
These system standards are distinguished from system standards for conventionally installed plastics
piping systems by the requirement to verify certain characteristics in the “as installed” condition,
after site processing. This is in addition to verification of characteristics of plastics piping systems “as
manufactured”.
Each of the system standards comprises a:
— Part 1: General
and all applicable renovation technique family-related parts, which for non-pressure drainage and
sewerage networks include or potentially include the following:
— Part 2: Lining with continuous pipes
— Part 3: Lining with close-fit pipes (this document)
— Part 4: Lining with cured-in-place pipes
— Part 5: Lining with discrete pipes
— Part 7: Lining with spirally-wound pipes
— Part 8: Lining with pipe segments
— Part 9: Lining with rigidly anchored plastics inner layer
— Part 10: Lining with sprayed polymeric materials
The requirements for any given renovation technique family are specified in Part 1, applied in
conjunction with the relevant other part. For example, both ISO 11296-1 and this document together
specify the requirements relating to lining with close-fit pipes. For complementary information, see
ISO 11295. Not all technique families are pertinent to every area of application and this is reflected in
the part numbers included in each system standard.
A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons
across renovation technique families.
Figure 1 shows the common part and clause structure and the relationship between ISO 11296 and
system standards for other applications.
vi © ISO 2018 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
Figure 1 — Format of the renovation system standards
© ISO 2018 – All rights reserved vii
---------------------- Page: 13 ----------------------
SIST EN ISO 11296-3:2018
---------------------- Page: 14 ----------------------
SIST EN ISO 11296-3:2018
INTERNATIONAL STANDARD ISO 11296-3:2018(E)
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks —
Part 3:
Lining with close-fit pipes
1 Scope
This document, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit
lining systems used for the renovation of underground non-pressure drainage and sewerage networks.
It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U)
as manufactured, as well to the installed lining system with its associated joints.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 4435, Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized
poly(vinyl chloride) (PVC-U)
ISO 6259-1, Thermoplastics pipes — Determination of tensile properties — Part 1: General test method
ISO 8772, Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE)
ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified
temperature (DCMT) — Test method
ISO 9967, Thermoplastics pipes — Determination of creep ratio
ISO 9969, Thermoplastics pipes — Determination of ring stiffness
ISO 11296-1:2018, Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks — Part 1: General
ISO 12176-1, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1:
Butt fusion
ISO 12176-2, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1:
Electrofusion
ISO 13953, Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of
test pieces from a butt-fused joint
ISO 18373-1:2007, Rigid PVC pipes — Differential scanning calorimetry (DSC) method — Part 1:
Measurement of the processing temperature
© ISO 2018 – All rights reserved 1
---------------------- Page: 15 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 11296-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http: //www .electropedia .org/
— ISO Online browsing platform: available at https: //www .iso .org/obp
3.1 General
3.1.1
close fit
situation of the outside of the installed liner relative to the inside of the existing pipeline, which may
either be an interference fit or include a small annular gap resulting from shrinkage and tolerances only
3.1.2
close-fit pipe
continuous lining pipe of thermoplastic material reshaped or otherwise expanded after insertion to
achieve a close fit to the existing pipeline
3.2 Techniques
No additional definitions apply.
3.3 Characteristics
3.3.1
MFR
melt mass-flow rate
rate of extrusion of a molten resin through a die of specified length and diameter under prescribed
conditions of temperature, load and piston position in the cylinder of an extrusion plastometer, the rate
being determined as the mass extruded over a specified time
Note 1 to entry: MFR is expressed in units of grams per 10 min.
[SOURCE: ISO 1133-1:2011, 3.1, modified - the second sentence in the NOTE has been deleted.]
3.4 Materials
3.4.1
crazing
microstructural phenomenon associated with the short-term application of tensile bending strain
exceeding the material-related critical yield strain
3.5 Product stages
No additional definitions apply.
3.6 Service conditions
No additional definitions apply.
2 © ISO 2018 – All rights reserved
---------------------- Page: 16 ----------------------
SIST EN ISO 11296-3:2018
ISO 11296-3:2018(E)
3.7 Joints
3.7.1
butt fusion joint
joint made by heating the planed ends of matching surfaces by holding them against a flat heating plate
until the PE material reaches fusion temperature, quickly removing the heating plate and pushing the
two softened ends against one another
3.7.2
fusion compatibility
ability of two similar or dissimilar PE materials to be fused together to form a joint which conforms to
the performance requirements of this document
4 Symbols and abbreviated terms
For the purposes of this document, the symbols and abbreviated terms given in ISO 11296-1 and the
following apply.
d original circular outside diameter of the pipe (before processing for insertion)
manuf
e maximum mean wall thickness
m, max
MFR melt mass-flow rate
OIT oxidation induction time
5 Pipes at the “M” stage
5.1 Materials
5.1.1 General
The material shall be either polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U), to which
are added those additives needed to facilitate the manufacture and/or installation of pipes conforming
t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.