SIST EN ISO 11357-7:2015
(Main)Plastics - Differential scanning calorimetry (DSC) - Part 7: Determination of crystallization kinetics (ISO 11357-7:2015)
Plastics - Differential scanning calorimetry (DSC) - Part 7: Determination of crystallization kinetics (ISO 11357-7:2015)
This part of ISO 11357 specifies two methods (isothermal and non-isothermal) for studying the
crystallization kinetics of partially crystalline polymers using differential scanning calorimetry (DSC).
It is only applicable to molten polymers.
NOTE These methods are not suitable if the molecular structure of the polymer is modified during the test.
Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 7: Bestimmung der Kristallisationskinetik (ISO 11357-7:2015)
Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 7: Détermination de la cinétique de cristallisation (ISO 11357-7:2015)
ISO 11357-7:2015 spécifie deux méthodes (isotherme et non isotherme), permettant d'étudier la cinétique de cristallisation de polymères semi-cristallins en utilisant l'analyse calorimétrique différentielle (DSC).
Elle s'applique uniquement aux polymères fondus.
NOTE Ces méthodes ne sont pas appropriées si la structure moléculaire du polymère est modifiée pendant l'essai.
Polimerni materiali - Diferenčna dinamična kalorimetrija (DSC) - 7. del: Ugotavljanje kristalizacijske kinetike ((ISO 11357-7:2015)
Ta del standarda ISO 11357 določa dve metodi (izotermično in neizotermično) za preučevanje kristalizacijske kinetike delno kristalničnih polimerov z diferenčno dinamično kalorimetrijo (DSC). Uporablja se samo za taljene polimere.
OPOMBA: Te metode niso primerne, če se molekulska struktura polimera med preskušanjem spremeni.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11357-7:2015
01-november-2015
1DGRPHãþD
SIST EN ISO 11357-7:2013
3ROLPHUQLPDWHULDOL'LIHUHQþQDGLQDPLþQDNDORULPHWULMD '6& GHO
8JRWDYOMDQMHNULVWDOL]DFLMVNHNLQHWLNH ,62
Plastics - Differential scanning calorimetry (DSC) - Part 7: Determination of crystallization
kinetics (ISO 11357-7:2015)
Kunststoffe - Dynamische Differenz-Thermoanalyse (DSC) - Teil 7: Bestimmung der
Kristallisationskinetik (ISO 11357-7:2015)
Plastiques - Analyse calorimétrique différentielle (DSC) - Partie 7: Détermination de la
cinétique de cristallisation (ISO 11357-7:2015)
Ta slovenski standard je istoveten z: EN ISO 11357-7:2015
ICS:
17.200.10 Toplota. Kalorimetrija Heat. Calorimetry
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11357-7:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11357-7:2015
---------------------- Page: 2 ----------------------
SIST EN ISO 11357-7:2015
EN ISO 11357-7
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2015
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 11357-7:2013
English Version
Plastics - Differential scanning calorimetry (DSC) - Part 7:
Determination of crystallization kinetics (ISO 11357-
7:2015)
Plastiques - Analyse calorimétrique différentielle (DSC) Kunststoffe - Dynamische Differenz-Thermoanalyse
- Partie 7: Détermination de la cinétique de (DSC) - Teil 7: Bestimmung der Kristallisationskinetik
cristallisation (ISO 11357-7:2015) (ISO 11357-7:2015)
This European Standard was approved by CEN on 31 July 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11357-7:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11357-7:2015
EN ISO 11357-7:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11357-7:2015
EN ISO 11357-7:2015 (E)
European foreword
This document (EN ISO 11357-7:2015) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall
be withdrawn at the latest by March 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 11357-7:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11357-7:2015 has been approved by CEN as EN ISO 11357-7:2015 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11357-7:2015
---------------------- Page: 6 ----------------------
SIST EN ISO 11357-7:2015
INTERNATIONAL ISO
STANDARD 11357-7
Second edition
2015-08-15
Plastics — Differential scanning
calorimetry (DSC) —
Part 7:
Determination of crystallization
kinetics
Plastiques — Analyse calorimétrique différentielle (DSC) —
Partie 7: Détermination de la cinétique de cristallisation
Reference number
ISO 11357-7:2015(E)
©
ISO 2015
---------------------- Page: 7 ----------------------
SIST EN ISO 11357-7:2015
ISO 11357-7:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11357-7:2015
ISO 11357-7:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials. 2
6 Test specimens. 2
7 Test conditions and specimen conditioning . 2
8 Calibration . 2
9 Procedure. 2
9.1 General . 2
9.2 Loading the test specimen into the crucible . 3
9.3 Insertion of the crucibles into the instrument . 3
9.4 Melting of the polymer . 3
9.5 Isothermal crystallization . 3
9.6 Non-isothermal crystallization . 4
10 Expression of results . 5
10.1 General . 5
10.2 Methods of determination of crystallization kinetics . 5
10.2.1 Isothermal crystallization . 5
10.2.2 Non-isothermal crystallization . 7
11 Precision . 8
12 Test report . 8
Annex A (informative) Equations for crystallization kinetics of polymers . 9
Bibliography .11
© ISO 2015 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11357-7:2015
ISO 11357-7:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 5, Physical-
chemical properties.
This second edition cancels and replaces the first edition (ISO 11357-7:2002), which has been technically
revised with the following changes:
a) values to be recorded for isothermal crystallization revised, starting time of the isothermal step
(t = 0) added (10.2.1), and Figure 2 to Figure 6 revised accordingly;
b) Formula (A.1) and Formula (A.2) are corrected;
c) dated references changed to undated references.
ISO 11357 consists of the following parts, under the general title Plastics — Differential scanning
calorimetry (DSC):
— Part 1: General principles
— Part 2: Determination of glass transition temperature and glass transition step height
— Part 3: Determination of temperature and enthalpy of melting and crystallization
— Part 4: Determination of specific heat capacity
— Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction
and degree of conversion
— Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature
(dynamic OIT)
— Part 7: Determination of crystallization kinetics
iv © ISO 2015 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11357-7:2015
INTERNATIONAL STANDARD ISO 11357-7:2015(E)
Plastics — Differential scanning calorimetry (DSC) —
Part 7:
Determination of crystallization kinetics
1 Scope
This part of ISO 11357 specifies two methods (isothermal and non-isothermal) for studying the
crystallization kinetics of partially crystalline polymers using differential scanning calorimetry (DSC).
It is only applicable to molten polymers.
NOTE These methods are not suitable if the molecular structure of the polymer is modified during the test.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.