Machines for compacting waste materials or recyclable fractions - Compactors - Safety requirements

This European Standard specifies the safety requirements for the design, manufacture and information for the safe use of compactors that compact waste material or recyclable fractions (e. g. paper, plastics, textiles, cans, cardboard, mixed waste), hereafter referred to as materials.
This European Standard applies to:
—   compactors using a horizontally moving screw, pendulum or plate as compacting part and where the materials move horizontally; and
—   compactors that are mechanically fed and/or fed by hand.
These compactors can be:
—   static compactors;
—   transportable compactors;
—   traversing systems.
The scope includes:
—   any integral mechanical feed equipment (e.g. bin lift/skip hoist);
—   feed hoppers/openings;
—   any integral pre-conditioning equipment in the hopper (e.g. perforators, pre-crushing devices and shredders);
—   integral material flow control equipment;
—   the interface between the compactor and any feed equipment (except those excluded from the scope).
The scope of this European Standard does not cover:
—   compactors that are covered by EN 1501 (all parts);
—   underground compactors, however if these compactors can be used above ground this standard applies;
—   compactors using thermal technologies for compaction;
—   vacuum compactors;
—   compactors where materials are compacted vertically;
—   containers for static compactors, however the interface between the compactor and the container is included;
—   bins/skips in which materials are collected for feeding into the compactor;
—   any up-stream pre-treatment equipment that is not integral to the machine and is used to treat the materials before they are fed into the feed opening of the compactor;
—   vehicles including lifting equipment used to collect and transport the compactor or container;
—   cranes, lift trucks or other transportable plant used to load materials into the feed hopper/opening and the hazards arising out of using this equipment to load;
—   any suction or dust control equipment.
This European standard does not cover the lifting and transport of transportable compactors.
This European Standard does not apply to hazards arising from the materials being processed (e.g. asbestos, clinical waste, aerosol containers).
All hazards mentioned in Clause 4 are dealt with in this European Standard.
This European Standard is not applicable for compactors which are manufactured before the date of its publication as an EN.

Maschinen zum Verdichten von Abfällen oder recyclebaren Materialien - Verdichter - Sicherheitsanforderungen

Diese Europäische Norm legt die Sicherheitsanforderungen an die Konstruktion, die Herstellung und die Benutzerinformation zur sicheren Nutzung von Verdichtern zum Verdichten von Abfällen oder recyclebaren Materialien (z. B. Papier, Kunststoff, Textilien, Dosen, Pappe, gemischten Abfällen), nachstehend Materialien genannt, fest.
Diese Norm gilt für:
-   Verdichter, die als verdichtende Teile eine horizontal bewegliche Schnecke, ein Pendel oder eine Platte verwenden und bei denen die Materialien horizontal bewegt werden; und
-   Verdichter, die mechanisch und/oder von Hand beschickt werden.
Diese Verdichter können sein:
-   stationäre Verdichter;
-   transportable Verdichter;
-   verfahrbare Systeme.
Der Anwendungsbereich enthält:
-   jede fest eingebaute mechanische Beschickungseinrichtungen (z. B. Hub-Kipp-Vorrichtungen);
-   Zuführtrichter/-öffnungen;
-   jede fest eingebaute Vorbehandlungsanlagen im Zuführtrichter (z. B. Perforatoren, Vorzerkleinerungs-einrichtungen und Schredder);
-   jede eingebaute Anlagen zur Materialflusssteuerung;
-   die Schnittstelle zwischen dem Verdichter und den jeweiligen Beschickungseinrichtungen (mit Ausnahme der vom Anwendungsbereich ausgenommenen Schnittstellen).
Im Anwendungsbereich dieser Norm nicht enthalten sind:
-   in EN 1501 (alle Teile) behandelte Verdichter;
-   Untertage-Verdichter, wenngleich diese Norm gilt, sofern sie auch oberirdisch eingesetzt werden können;
-   Verdichter, die mittels thermischer Verfahren zur Verdichtung arbeiten;
-   Vakuumverdichter;
-   Verdichter, in denen Materialien vertikal verdichtet werden;
-   Behälter für stationäre Verdichter, wobei die Schnittstelle zwischen der Verdichtungseinheit und dem Behälter im Anwendungsbereich enthalten ist;
-   Tonnen, in denen Materialien gesammelt werden, die dem Verdichter zugeführt werden sollen;
-   alle vorgelagerten Vorbehandlungsanlagen, die nicht fest in die Maschine eingebaut sind und der Behandlung der Materialien dienen, bevor diese dem Verdichter über die Zuführöffnung zugeführt werden;
-   Fahrzeuge einschließlich Hebevorrichtungen zur Aufnahme und zum Transport des Verdichters oder Behälters;
-   Kräne, Gabelstapler oder sonstige transportable Maschinen, die der Zufuhr von Materialien in den Zuführtrichter/die Zuführöffnung dienen sowie die Gefährdungen, die durch den Einsatz dieser Ausrüstungen für die Beschickung entstehen;
-   alle Absaug- oder Entstaubungsanlagen.
Diese Europäische Norm behandelt nicht den Hebevorgang und Transport transportabler Verdichter.
Diese Europäische Norm gilt nicht für Gefährdungen, die durch die verarbeiteten Materialien (z. B. Asbest, Klinikabfälle, Sprühdosen) entstehen.
Alle in Abschnitt 4 aufgeführten Gefährdungen werden in dieser Europäischen Norm behandelt.
Diese Europäische Norm gilt nicht für Verdichter, die vor dem Veröffentlichungsdatum dieser EN hergestellt wurden.

Machines de compactage pour déchets ou matières recyclables - Compacteurs - Prescriptions de sécurité

La présente Norme européenne spécifie les prescriptions de sécurité applicables à la conception, à la construction et aux informations pour l’utilisation en sécurité des compacteurs pour déchets ou matières recyclables (tels que papier, matières plastiques, textiles, canettes, carton, déchets mélangés), ci après dénommés matériaux.
La présente Norme européenne s’applique :
-   aux compacteurs utilisant comme élément presseur une vis, une pelle ou un plateau se déplaçant horizontalement, et dans lesquels les matériaux sont poussés horizontalement ;
-   aux compacteurs chargés mécaniquement et/ou manuellement.
Ces compacteurs peuvent être :
-   des compacteurs désaccouplables ;
-   des compacteurs monobloc ;
-   des systèmes à translation.
Le domaine d’application couvre :
-   tout équipement de chargement mécanique faisant partie intégrante de la machine (lève-conteneurs, par exemple) ;
-   les trémies/ouvertures de chargement ;
-   tout équipement de pré-conditionnement placé dans la trémie et faisant partie intégrante de la machine (perforateurs, dispositifs de broyage et déchiqueteurs, par exemple) ;
-   tout équipement de régulation du flux de matériaux faisant partie intégrante de la machine ;
-   l’interface entre le compacteur et tout équipement de chargement (à l’exception de ceux qui sont exclus du domaine d’application).
Le domaine d’application de la présente Norme européenne ne couvre pas :
-   les compacteurs couverts par l’EN 1501 (toutes les parties) ;
-   les compacteurs installés sous terre ; toutefois, la présente norme s’applique à ces compacteurs s’ils peuvent aussi être utilisés en surface ;
-   les compacteurs utilisant des technologies thermiques pour le compactage ;
-   les compacteurs à dépression ;
-   les compacteurs dans lesquels les matériaux sont compactés verticalement ;
-   les caissons pour compacteurs désaccouplables ; toutefois, l’interface entre l’unité de compaction et le caisson est couverte ;
-   les bennes de collecte des matériaux à compacter ;
-   tout équipement amont de pré-conditionnement ne faisant pas partie intégrante de la machine et utilisé pour traiter les matériaux avant qu’ils soient introduits dans l’ouverture de chargement du compacteur ;
-   les véhicules de reprise et de transport du compacteur ou du caisson, ni leurs équipements de levage ;
-   les grues, chariots industriels ou autres engins mobiles utilisés pour charger les matériaux dans la trémie/l’ouverture de chargement, ni les phénomènes dangereux résultant du chargement au moyen de ces équipements ;
-   tout équipement d’aspiration et de dépoussiérage.
La présente Norme européenne ne couvre pas les opérations de levage et de transport des compacteurs monobloc.
La présente Norme européenne ne s’applique pas aux phénomènes dangereux résultant des matériaux traités (amiante, déchets médicaux, générateurs d’aérosols, par exemple).
Tous les phénomènes dangereux mentionnés à l’Article 4 sont traités dans la présente Norme européenne.
La présente Norme européenne n'est pas applicable aux compacteurs fabriqués avant sa date de publication comme EN.

Stroji za stiskanje odpadkov ali reciklirnih materialov - Kompaktorji (zgoščevalniki) - Varnostne zahteve- Dopolnilo 1

General Information

Status
Not Published
Public Enquiry End Date
29-Nov-2018
Technical Committee
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
20-Dec-2019
Due Date
07-Feb-2020
Completion Date
05-May-2020

Relations

Buy Standard

Draft
EN 16486:2014/oprA1:2018
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16486:2014/oprA1:2018
01-november-2018
6WURML]DVWLVNDQMHRGSDGNRYDOLUHFLNOLUQLKPDWHULDORY.RPSDNWRUML ]JRãþHYDOQLNL
9DUQRVWQH]DKWHYH'RSROQLOR
Machines for compacting waste materials or recyclable fractions - Compactors - Safety
requirements
Maschinen zum Verdichten von Abfällen oder recyclebaren Materialien - Verdichter -
Sicherheitsanforderungen
Machines de compactage pour déchets ou matières recyclables - Compacteurs -
Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 16486:2014/prA1:2018
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
SIST EN 16486:2014/oprA1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 16486:2014/oprA1:2018

---------------------- Page: 2 ----------------------

SIST EN 16486:2014/oprA1:2018


DRAFT
EUROPEAN STANDARD
EN 16486:2014
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
September 2018
ICS 43.160
English Version

Machines for compacting waste materials or recyclable
fractions - Compactors - Safety requirements
Machines de compactage pour déchets ou matières Maschinen zum Verdichten von Abfällen oder
recyclables - Compacteurs - Prescriptions de sécurité recyclebaren Materialien - Verdichter -
Sicherheitsanforderungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 397.

This draft amendment A1, if approved, will modify the European Standard EN 16486:2014. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16486:2014/prA1:2018:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 16486:2014/oprA1:2018
EN 16486:2018/prA1:2018 (E)
Contents Page

European foreword . 3
1 Addition to 4.1.1 General . 4
2 Addition to 4.3 Electrical hazards . 4
3 Addition to 5.3 Electrical hazards .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.