SIST EN 62317-7:2007

Ferrite cores - Dimensions -- Part 7: EER-cores

This part of IEC 62317 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EER-cores made of ferrite, the essential
dimensions of coil formers to be used with them, and the effective parameter values to be used in calculations involving them.

Ferritkerne - Maße -- Teil 7: EER-Kerne

Noyaux ferrites - Dimensions -- Partie 7: Noyaux EER

Feritna jedra – Mere – 7. del: EER-jedra (IEC 62317-7:2005)

General Information

• Status: Published
• Publication Date: 11-Sep-2007
• ICS: 29.100.10 - Magnetic components
• Technical Committee: IMKF - Magnetic components and ferrite materials
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 11-Sep-2007
• Due Date: 16-Nov-2007
• Completion Date: 12-Sep-2007
• Ref Project: EN 62317-7:2005 - Ferrite cores - Dimensions - Part 7: EER-cores

Relations

• Replaced By: SIST EN IEC 63093-7:2018 - Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7: EER-cores
• Effective Date: 16-Oct-2018

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62317-7:2007
01-november-2007
Feritna jedra – Mere – 7. del: EER-jedra (IEC 62317-7:2005)
Ferrite cores - Dimensions -- Part 7: EER-cores (IEC 62317-7:2005)
Ferritkerne - Maße -- Teil 7: EER-Kerne (IEC 62317-7:2005)
Noyaux ferrites - Dimensions -- Partie 7: Noyaux EER (IEC 62317-7:2005)
Ta slovenski standard je istoveten z: EN 62317-7:2005
ICS:
29.100.10 Magnetne komponente Magnetic components
SIST EN 62317-7:2007 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 62317-7
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2005

ICS 29.100.10


English version


Ferrite cores –
Dimensions
Part 7: EER-cores
(IEC 62317-7:2005)


Noyaux ferrites –  Ferritkerne –
Dimensions Maße
Partie 7: Noyaux EER Teil 7: EER-Kerne
(CEI 62317-7:2005) (IEC 62317-7:2005)






This European Standard was approved by CENELEC on 2005-10-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in two official versions (English, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 62317-7:2005 E

---------------------- Page: 2 ----------------------

EN 62317-7:2005 - 2 -
Foreword
The text of document 51/834/FDIS, edition 1 of IEC 62317-7, prepared by IEC TC 51, Magnetic
components and ferrite materials, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 62317-7 on 2005-10-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-10-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62317-7:2005 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 62317-7:2005
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60205 2001 Calculation of the effective parameters of EN 60205 2001
magnetic piece parts

IEC 62358 2004 Ferrite cores - Standard inductance factor EN 62358 2004
(AL) and its tolerance

---------------------- Page: 4 ----------------------

INTERNATIONAL IEC


STANDARD 62317-7





First edition
2005-09


Ferrite cores – Dimensions –
Part 7:
EER-cores

 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale K
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

---------------------- Page: 5 ----------------------

– 2 – 62317-7  IEC:2005(E)
CONTENTS
FOREWORD.3

1 Scope.6
2 Normative references .6
3 Primary standards .6
3.1 Dimensions of EER-cores.6
3.2 Dimensional limits for coil formers .6

Annex A (normative) Derived standards .9
Annex B (normative) Example of a standard for gauges to check the dimensions of
EER-cores meeting this primary standard .10

Figure 1 – Dimensions of EER-cores .7
Figure 2 – Essential dimensions of coil formers .8
Figure B.1 – Gauge dimensions .10

Table 1 – Dimensions of EER-cores.7
Table 2 – Effective parameter values of EER-cores .7
Table 3 – Essential dimensions of coil formers .8
Table B.1 – Gauge dimensions .10

---------------------- Page: 6 ----------------------

62317-7  IEC:2005(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FERRITE CORES – DIMENSIONS

Part 7: EER-cores


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards. Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)“). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any ot
...