SIST EN 13481-2:2012/FprA1:2016
(Amendment)Railway applications - Track - Performance requirements for fastening systems - Part 2: Fastening systems for concrete sleepers
Railway applications - Track - Performance requirements for fastening systems - Part 2: Fastening systems for concrete sleepers
This European Standard is applicable to fastening systems, in categories A - E (see EN 13481 1:2012, 3.1), for use on concrete sleepers in ballasted track with maximum axle loads and minimum curve radii in accordance with Table 1. Table 1 - Fastening category criteria Category Maximum design axle load kN Minimum curve radius m A 130 40 B 180 80 C 260 150 D 260 400 E 350 150 NOTE The maximum axle load for categories A and B does not apply to maintenance vehicles. The requirements apply to: - fastening systems which act on the foot and/or web of the rail including direct fastening systems and indirect fastening systems; - fastening systems for the rail sections in EN 13674-1 (excluding 49 E4) and EN 13674-4+A1. This standard is not applicable to fastening systems for other rail sections, rigid fastening systems or special fastening systems used at bolted joints or glued joints. This standard is for type approval of a complete fastening assembly only.
Bahnanwendungen - Oberbau - Leistungsanforderungen für Schienenbefestigungssysteme - Teil 2: Befestigungssysteme für Betonschwellen
Applications ferroviaires - Voie - Exigences de performance pour les systèmes de fixation - Partie 2: Systèmes de fixation pour traverses en béton
Železniške naprave - Zgornji ustroj - Zahteve za izdelavo pritrdilnih sistemov - 2. del: Pritrdilni sistemi za betonske prage - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13481-2:2012/FprA1:2016
01-april-2016
Železniške naprave - Zgornji ustroj - Zahteve za izdelavo pritrdilnih sistemov - 2.
del: Pritrdilni sistemi za betonske prage - Dopolnilo A1
Railway applications - Track - Performance requirements for fastening systems - Part 2:
Fastening systems for concrete sleepers
Bahnanwendungen - Oberbau - Leistungsanforderungen für
Schienenbefestigungssysteme - Teil 2: Befestigungssysteme für Betonschwellen
Applications ferroviaires - Voie - Exigences de performance pour les systèmes de
fixation - Partie 2: Systèmes de fixation pour traverses en béton
Ta slovenski standard je istoveten z: EN 13481-2:2012/FprA1:2016
ICS:
93.100 Gradnja železnic Construction of railways
SIST EN 13481-2:2012/FprA1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13481-2:2012/FprA1:2016
---------------------- Page: 2 ----------------------
SIST EN 13481-2:2012/FprA1:2016
FINAL DRAFT
EUROPEAN STANDARD
EN 13481-2:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
February 2016
ICS 93.100
English Version
Railway applications - Track - Performance requirements
for fastening systems - Part 2: Fastening systems for
concrete sleepers
Applications ferroviaires - Voie - Exigences de Bahnanwendungen - Oberbau -
performance pour les systèmes de fixation - Partie 2: Leistungsanforderungen für
Systèmes de fixation pour traverses en béton Schienenbefestigungssysteme - Teil 2:
Befestigungssysteme für Betonschwellen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical
Committee CEN/TC 256.
This draft amendment A1, if approved, will modify the European Standard EN 13481-2:2012. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13481-2:2012/FprA1:2016:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13481-2:2012/FprA1:2016
EN 13481-2:2012/FprA1:2016 (E)
Contents Page
European foreword .3
1 Modification to the Scope .4
2 Modification to Clause 2, Normative references .5
3 Modification to 5.5, Effect of repeated loading .5
4 Modification to 5.11, Cast-in and glued-in fastening components .5
5 Modification to Annex A, Vertical load test for cast-in and glued-in fastening components .6
6 Modification to Annex ZA .6
2
---------------------- Page: 4 ----------------------
SIST EN 13481-2:2012/FprA1:2016
EN 13481-2:2012/FprA1:2016 (E)
European foreword
This document (EN 13481-2:2012/FprA1:2016) has been prepared by Technical Committee
CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2008/57/EC.
For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of
this document.
3
---------------------- Page: 5 ----------------------
SIST EN 13481-2:2012/FprA1:2016
EN 13481-2:2012/FprA1:2016 (E)
1 Modification to the Scope
Replace the scope with the following:
"This European Standard is applicable to fastening systems in Categories A–E as specified in
EN 13481-1:2012, 3.1, for use on concrete sleepers in ballasted track with maximum axle loads, and
minimum curve radii as shown in Table 1.
Table 1 — Fastening category criteria
Category Maximum design axle load Minimum curve radius
kN m
A 130 40
B 180 80
C 260 150
D 260 400
E 350 150
NOTE The maximum axle load for Categories A and B does not apply to maintenance vehicles.
The requirements apply to:
fastening systems which act on the foot and/or web of the rail including direct fastening systems
and indirect fastening systems;
fastening systems with dynamic stiffness, k , not less than 50 MN/m;
LFA
fastening systems for rail sections included in EN 13674-1 (excluding 49E4) or EN 13674-4.
This st
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.