iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN ISO 16486-1:2023

(Amendment)

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO/DIS 16486-1:2023)

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO/DIS 16486-1:2023)

This document specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
This document establishes a calculation and design scheme on which to base the maximum operating pressure (MOP) of a PA-U piping system.

Kunststoff-Rohrleitungssysteme für die Gasversorgung - Rohrleitungssysteme aus weichmacherfreiem Polyamid (PA-U) mit Schweißverbindungen und mechanischen Verbindungen - Teil 1: Allgemeines (ISO/DIS 16486-1:2023)

Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux - Systèmes de canalisations en polyamide non plastifié (PA-U) avec assemblages par soudage et assemblages mécaniques - Partie 1: Généralités (ISO/DIS 16486-1:2023)

Le présent document spécifie les propriétés générales des compositions de polyamide non plastifié (PA-U) pour la fabrication de tubes, raccords et robinets fabriqués à partir de la composition, destinés à être enterrés et utilisés pour la distribution de combustibles gazeux. Il spécifie également les paramètres d’essai pour les méthodes d’essai auxquelles il fait référence.
La série ISO 16486 s’applique aux systèmes de canalisations en PA-U dont les composants sont raccordés par des assemblages par soudage et/ou par des assemblages mécaniques.
Ce document établit un schéma de calcul et de conception sur lequel baser la pression maximale de service (MOP) d’un système de canalisations en PA-U.
NOTE            Dans le cadre du présent document, le terme de combustibles gazeux comprend par exemple le gaz naturel, le méthane, le butane, le propane, l'hydrogène, le gaz manufacturé, le biogaz et les mélanges de ces gaz.

Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Cevni sistemi iz nemehčanega poliamida (PA-U) z zvari in mehanskimi spoji - 1. del: Splošno (ISO/DIS 16486-1:2023)

General Information

Status
Not Published
Public Enquiry End Date
16-Apr-2023
ICS
75.200 - Petroleum products and natural gas handling equipment
83.140.30 - Plastics pipes and fittings for non fluid use
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
24-Jan-2024
Due Date
30-Mar-2024
Ref Project
EN ISO 16486-1:2023 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2023)

Relations

Replaces
SIST EN ISO 16486-1:2020 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2020)
Effective Date
20-Apr-2022
Revises
SIST EN ISO 16486-1:2020 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2020)
Effective Date
19-Jan-2023
Revised
SIST EN ISO 16486-1:2020 - Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2020)
Effective Date
18-Jan-2023

Buy Standard

prEN ISO 16486-1:2023prEN ISO 16486-1:2023
PreviousNext
Draft
prEN ISO 16486-1:2023
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 16486-1:2023
01-april-2023
Nadomešča:
SIST EN ISO 16486-1:2020
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Cevni sistemi
iz nemehčanega poliamida (PA-U) z zvari in mehanskimi spoji - 1. del: Splošno
(ISO/DIS 16486-1:2023)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U)
piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO/DIS
16486-1:2023)
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Rohrleitungssysteme aus
weichmacherfreiem Polyamid (PA-U) mit Schweißverbindungen und mechanischen
Verbindungen - Teil 1: Allgemeines (ISO/DIS 16486-1:2023)
Systèmes de canalisations en matières plastiques pour la distribution de combustibles
gazeux - Systèmes de canalisations en polyamide non plastifié (PA-U) avec
assemblages par soudage et assemblages mécaniques - Partie 1: Généralités (ISO/DIS
16486-1:2023)
Ta slovenski standard je istoveten z: prEN ISO 16486-1
ICS:
75.200 Oprema za skladiščenje Petroleum products and
nafte, naftnih proizvodov in natural gas handling
zemeljskega plina equipment
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
oSIST prEN ISO 16486-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 16486-1:2023

---------------------- Page: 2 ----------------------
oSIST prEN ISO 16486-1:2023


DRAFT
EUROPEAN STANDARD
prEN ISO 16486-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

January 2023
ICS 75.200; 83.140.30 Will supersede EN ISO 16486-1:2020
English Version

Plastics piping systems for the supply of gaseous fuels -
Unplasticized polyamide (PA-U) piping systems with
fusion jointing and mechanical jointing - Part 1: General
(ISO/DIS 16486-1:2023)
Systèmes de canalisations en matières plastiques pour Kunststoff-Rohrleitungssysteme für die Gasversorgung
la distribution de combustibles gazeux - Systèmes de - Rohrleitungssysteme aus weichmacherfreiem
canalisations en polyamide non plastifié (PA-U) avec Polyamid (PA-U) mit Schweißverbindungen und
assemblages par soudage et assemblages mécaniques - mechanischen Verbindungen - Teil 1: Allgemeines
Partie 1: Généralités (ISO/DIS 16486-1:2023) (ISO/DIS 16486-1:2023)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical
Committee CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 16486-1:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN ISO 16486-1:2023
prEN ISO 16486-1:2023 (E)
Contents Page
European foreword . 3
Annex (informative)  A-deviation . 4

2

---------------------- Page: 4 ----------------------
oSIST prEN ISO 16486-1:2023
prEN ISO 16486-1:2023 (E)
European foreword
This document (prEN ISO 16486-1:2023) has been prepared by Technical Committee ISO/TC
138 “Plastics pipes, fittings and valves for the transport of fluids” in collaboration with
Technical Co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TS CEN ISO/TS 16486-7:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 7: Assessment of conformity (ISO/TS 16486-7:2023)
CEN ISO/TS 16486-7:2023

This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of the ISO 16486 series which are intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1    A basic test matrix in Annex B provides an overview of the testing scheme.
It is recommended for the manufacturer to have a management system such as ISO 9001[4] or equivalent.
NOTE 2    If certification is involved, certification bodies and inspection bodies operating according to ISO/IEC 17065 and ISO/IEC 17020 are considered to be competent.
In conjunction with the other parts of the ISO 16486 series (see Clause 2), this document is applicable to unplasticized polyamide (PA-U) piping systems intended to be buried and used for the supply of gaseous fuels. It is applicable to PA-U pipes, fittings and valves, as well as to their joints and to joints with components of other materials intended to be used under the following conditions:
a)    a maximum operating pressure (MOP) up to and including 18 bar[1] (the MOP is limited to 16 bar for CEN member countries, where ISO 16486-6 is replaced by CEN/TS 12007-6[1]);
b)    an operating temperature of 20 °C as the reference temperature.
NOTE 3    For operating temperatures different to 20 °C, derating coefficients can be used (see ISO 16486-6). CEN member countries use CEN/TS 12007-6[1] and ISO/TS 16486-7 (this document) as a basis, but they can also request additional requirements. For non-CEN member countries, information for dealing with special cases for PA-U can be found in ISO/TS 16486-7 (this document) and PPI TR-3.[7]
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this document. When requested, a quality plan based on the tests mentioned can be set up in agreement between user and manufacturer.
The ISO 16486 series covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 4    It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-4:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)
EN ISO 16486-4:2022

This part of ISO 16486 specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486 1, intended to be buried and used for the supply of gaseous fuels.
Valves made from other material than unplasticized polyamide designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PA-U piping system according to ISO 16486 provided they have relevant PA-U connections for butt fusion or electrofusion ends (see ISO 164863). The component, i.e. the complete valve, shall fulfil the requirements of this part of ISO 16486.
It also specifies the test parameters for the test methods referred to in this part of ISO 16486.
It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be jointed with PA-U pipes conforming to ISO 16486 2 without any fittings or with PA-U fittings conforming to ISO 164863.
This part of ISO 16486 covers valves for pipes with a nominal outside diameter, dn, ≤250 mm.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-5:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system (ISO 16486-5:2021)
EN ISO 16486-5:2021

This part of ISO 16486 specifies the requirements of fitness for purpose of the unplasticized polyamide (PA-U) piping system, intended to be buried and used for the supply of gaseous fuels. It also specifies the definitions of electrofusion and butt fusion joints.
This part of ISO 16486 specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints and to joints with components of PA-U.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-2:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2020)
EN ISO 16486-2:2020

This part of ISO 16486 specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirements for the marking of pipes.
Pipes conforming to this part of ISO 16486 are jointed typically by using mechanical, electrofusion or butt fusion (see Annex A) techniques, but not by solvent cement jointing.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-3:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO 16486-3:2020)
EN ISO 16486-3:2020

This part of ISO 16486 specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirements for the marking of fittings.
In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints, to joints with components of PA-U and to joints with mechanical fittings of other materials, and to the following fitting types:
    — fusion fittings — electrofusion fittings and butt fusion fittings;
    — transition fittings.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-1:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2020)
EN ISO 16486-1:2020

This part of ISO 16486 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN ISO/TS 16486-7:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 7: Assessment of conformity (ISO/TS 16486-7:2023)
CEN ISO/TS 16486-7:2023

This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of the ISO 16486 series which are intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1    A basic test matrix in Annex B provides an overview of the testing scheme.
It is recommended for the manufacturer to have a management system such as ISO 9001[4] or equivalent.
NOTE 2    If certification is involved, certification bodies and inspection bodies operating according to ISO/IEC 17065 and ISO/IEC 17020 are considered to be competent.
In conjunction with the other parts of the ISO 16486 series (see Clause 2), this document is applicable to unplasticized polyamide (PA-U) piping systems intended to be buried and used for the supply of gaseous fuels. It is applicable to PA-U pipes, fittings and valves, as well as to their joints and to joints with components of other materials intended to be used under the following conditions:
a)    a maximum operating pressure (MOP) up to and including 18 bar[1] (the MOP is limited to 16 bar for CEN member countries, where ISO 16486-6 is replaced by CEN/TS 12007-6[1]);
b)    an operating temperature of 20 °C as the reference temperature.
NOTE 3    For operating temperatures different to 20 °C, derating coefficients can be used (see ISO 16486-6). CEN member countries use CEN/TS 12007-6[1] and ISO/TS 16486-7 (this document) as a basis, but they can also request additional requirements. For non-CEN member countries, information for dealing with special cases for PA-U can be found in ISO/TS 16486-7 (this document) and PPI TR-3.[7]
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this document. When requested, a quality plan based on the tests mentioned can be set up in agreement between user and manufacturer.
The ISO 16486 series covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 4    It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14870-4:2023(Main)
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 4: Factory cold bends (ISO 15590-4:2019, modified)
EN 14870-4:2023

This document specifies the technical delivery conditions for bends made by the cold bending process for bend with radii 5xOD or higher for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.
NOTE 1   ISO 13623 is modified adopted as EN 14161 to exclude on-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances.
This document also specifies the requirements for the manufacture of two product specification levels (PSLs) of cold bends corresponding to product specification levels given for pipe in ISO 3183. This document is applicable to cold bends made from seamless and welded pipe of unalloyed or low-alloy steels.
NOTE 2   These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183.
This document is not applicable to the selection of the cold bend product specification level. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements.
NOTE 3   See also ISO 3183:2012, Introduction.
This document is not applicable to field cold bends and pipeline bends made by other manufacturing processes.
On-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances are excluded from the scope of this document.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14870-1:2023(Main)
Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2018, modified)
EN 14870-1:2023

This document specifies the technical delivery conditions for bends made by the induction bending process for use in pipeline transportation systems for the petroleum and natural gas industries as defined in ISO 13623.
NOTE 1   ISO 13623 is modified adopted as EN 14161 to exclude on-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances.
This document is applicable to induction bends made from seamless and welded pipe of unalloyed or low-alloy steels.
NOTE 2   These are typically C-Mn steels or low-alloy steels that are appropriate for the corresponding level and grade of line pipe in accordance with ISO 3183.
This document specifies the requirements for the manufacture of two product specification levels (PSLs) of induction bends corresponding to product specification levels given for pipe in ISO 3183.
This document is not applicable to the selection of the induction bend PSL. It is the responsibility of the purchaser to specify the PSL, based upon the intended use and design requirements; see also ISO 3183, Introduction.
This document is not applicable to pipeline bends made by other manufacturing processes.
On-land supply systems used by the European gas supply industry from the input of gas into the on-land transmission network up to the inlet connection of gas appliances are excluded from the scope of this document.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16486-4:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)
EN ISO 16486-4:2022

This part of ISO 16486 specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486 1, intended to be buried and used for the supply of gaseous fuels.
Valves made from other material than unplasticized polyamide designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PA-U piping system according to ISO 16486 provided they have relevant PA-U connections for butt fusion or electrofusion ends (see ISO 164863). The component, i.e. the complete valve, shall fulfil the requirements of this part of ISO 16486.
It also specifies the test parameters for the test methods referred to in this part of ISO 16486.
It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be jointed with PA-U pipes conforming to ISO 16486 2 without any fittings or with PA-U fittings conforming to ISO 164863.
This part of ISO 16486 covers valves for pipes with a nominal outside diameter, dn, ≤250 mm.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day