SIST EN 14219:2004
(Main)Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)
Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)
This European Standard specifies the characteristics of hexagon bolts with flange with metric fine pitch thread, small series, with product grade A, with nominal thread diameters from 8 mm up to and including 16 mm and property classes 8.8, 9.8, 10.9, 12.9 and A2-70.
If, in special cases, specifications other than those listed in this European Standard are required, they shall be selected from existing European and International Standards, for example ISO 261 ISO 724, ISO 888, EN ISO 898-1, ISO 965-2, EN ISO 3506-1.
Sechskantschrauben mit Flansch mit Feingewinde - Leichte Reihe (ISO 15072:1999, modifiziert)
Diese Europäische Norm legt die Eigenschaften von Sechskantschrauben mit Flansch mit metrischem Feingewinde, leichte Reihe, mit Produktklasse A, mit Gewinde-Nenndurchmessern von 8 mm bis 16 mm und mit Festigkeitsklassen 8.8, 10.9, 12.9 und A2-70 fest.
Wenn, in besonderen Fällen, andere Festlegungen als die in dieser Europäischen Norm benötigt werden, sollten sie den bestehenden Europäischen und Internationalen Normen, z. B. ISO 724, ISO 888,
EN ISO 898-1, ISO 965-2, EN ISO 3506-1, entnommen werden.
Vis a tete hexagonale a embase cylindro-tronçonique a pas fin - Série étroite (ISO 15072:1999, modifiée)
Šestroba glava vijaka s krajcem in metričnim finim navojem - Lahka izvedba (ISO 15072:1999, dopolnjen)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sechskantschrauben mit Flansch mit Feingewinde - Leichte Reihe (ISO 15072:1999, modifiziert)Vis a tete hexagonale a embase cylindro-tronçonique a pas fin - Série étroite (ISO 15072:1999, modifiée)Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified)21.060.10Sorniki, vijaki, stebelni vijakiBolts, screws, studs21.040.10Metrski navojiMetric screw threadsICS:Ta slovenski standard je istoveten z:EN 14219:2003SIST EN 14219:2004en01-januar-2004SIST EN 14219:2004SLOVENSKI
STANDARD
SIST EN 14219:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14219April 2003ICS 21.060.10English versionHexagon bolts with flange with metric fine pitch thread - Smallseries (ISO 15072:1999, modified)Vis à tête hexagonale à embase cylindro-tronçonique à pasfin - Série étroite (ISO 15072:1999, modifiée)Sechskantschrauben mit Flansch mit Feingewinde - LeichteReihe (ISO 15072:1999, modifiziert)This European Standard was approved by CEN on 14 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14219:2003 ESIST EN 14219:2004
EN 14219:2003 (E)2ForewordThis document (EN 14219:2003) has been prepared by Technical Committee CEN/TC 185 "Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latestby October 2003.Annex A is normative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.Endorsement noticeThe text of the International Standard ISO 15072:1999 was approved by CEN as a European Standard with agreedcommon modifications as given below.Bolts in accordance with this European Standard correspond to those specified in the International StandardISO 15072:1999 with the exception that the width across flats for M12 is 16 mm (instead of 15 mm) and that theproperty class 9.8 was deleted. Moreover, the option for surface coatings according to ISO 10683 was added.SIST EN 14219:2004
EN 14219:2003 (E)31 ScopeThis European Standard specifies the characteristics of hexagon bolts with flange with metric fine pitch thread,small series, with product grade A, with nominal thread diameters from 8 mm up to and including 16 mm and prop-erty classes 8.8, 9.8, 10.9, 12.9 and A2-70.If, in special cases, specifications other than those listed in this European Standard are required, they shall be se-lected from existing European and International Standards, for example ISO 261 ISO 724, ISO 888, EN ISO 898-1,ISO 965-2, EN ISO 3506-1.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 20225, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions (ISO 225:1983).EN 26157-3, Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements(ISO 6157-3:1988).EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws andstuds (ISO 898-1:1999).EN ISO 3269, Fasteners — Acceptance inspection (ISO 3269:2000).EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless-steel fasteners — Part 1: Bolts, screws andstuds (ISO 3506-1:1997).EN ISO 4042, Fasteners — Electroplated coatings (ISO 4042:1999).EN ISO 4753, Fasteners — Ends of parts with external ISO metric screw thread (ISO 4753:1999).EN ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C(ISO 4759-1:2000).EN ISO 10683, Fasteners — Non-electrolytically applied zinc flake coatings (ISO 10683:2000).ISO 724, ISO general purpose metric screw threads — Basic dimensions.ISO 261:1998, ISO general purpose metric screw threads –General planISO 965-2, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purposeexternal and internal screw threads — Medium quality.ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts.SIST EN 14219:2004
EN 14219:2003 (E)43 DimensionsDimensions shall be in accordance with Figures 1 to 4 and Table 1.NOTE
Symbols and designations of dimensions are specified in EN 20225.KeyaThe top of the head shall be either full form or indented at the manufacturer's discretion option and shall be either cham-fered or rounded. The minimum diameter of the chamfer circle or start of rounding shall be equal to the maximum width across flats minus 15 %. If the top of the head is indented, the periphery may be rounded.bEdge contour opti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.