SIST EN ISO 8765:2022
(Main)Fasteners - Hexagon head bolts, with fine pitch thread - Product grades A and B (ISO 8765:2022)
Fasteners - Hexagon head bolts, with fine pitch thread - Product grades A and B (ISO 8765:2022)
This document specifies the characteristics of hexagon head bolts, in steel and stainless steel, with
metric fine pitch threads M8×1 to M64×4, and with product grades A and B.
If in certain cases other specifications are requested, property classes and stainless steel grades can be
selected from ISO 898-1 or ISO 3506-1, and dimensional options from ISO 888 or ISO 4753
Mechanische Verbindungselemente - Sechskantschrauben mit Schaft und metrischem Feingewinde - Produktklassen A und B (ISO 8765:2022)
Dieses Dokument legt Eigenschaften für Sechskantschrauben mit Schaft aus Stahl und nichtrostendem Stahl mit metrischem Feingewinde von M8×1 bis M64×4 in Produktklasse A und B fest.
ANMERKUNG Falls in bestimmten Fällen andere Festlegungen benötigt werden, können Festigkeitsklassen und Güten nichtrostender Stähle aus ISO 898-1 oder ISO 3506-1 und Maßangaben aus ISO 888 oder ISO 4753 entnommen werden.
Fixations - Vis à tête hexagonale partiellement filetées, à pas fin - Grades A et B (ISO 8765:2022)
Le présent document spécifie les caractéristiques des vis à tête hexagonale partiellement filetées, en acier et en acier inoxydable, à filetage métrique à pas fin M8×1 à M64×4, et de grades A et B.
Si dans certains cas d’autres spécifications sont requises, les classes de qualité et les grades d’acier inoxydable peuvent être choisis dans l'ISO 898‑1 ou l'ISO 3506‑1, et les options dimensionnelles dans l'ISO 888 ou l'ISO 4753.
Vezni elementi - Vijaki s šestrobo glavo z drobnim navojem - Razreda izdelave A in B (ISO 8765:2022)
Ta dokument določa značilnosti vijakov s šestrobo glavo iz jekla in nerjavnega jekla, z drobnim metričnim navojem velikosti M8 × 1 to M64 × 4 in razredoma izdelave A in B.
Če se v določenih primerih zahtevajo druge specifikacije, je razrede lastnosti in tipe nerjavnega jekla mogoče izbrati po standardih ISO 898-1 ali ISO 3506-1, dimenzijske možnosti pa po ISO 888 ali ISO 4753.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8765:2022
01-september-2022
Nadomešča:
SIST EN ISO 8765:2012
Vezni elementi - Vijaki s šestrobo glavo z drobnim navojem - Razreda izdelave A in
B (ISO 8765:2022)
Fasteners - Hexagon head bolts, with fine pitch thread - Product grades A and B (ISO
8765:2022)
Mechanische Verbindungselemente - Sechskantschrauben mit Schaft und metrischem
Feingewinde - Produktklassen A und B (ISO 8765:2022)
Fixations - Vis à tête hexagonale partiellement filetées, à pas fin - Grades A et B (ISO
8765:2022)
Ta slovenski standard je istoveten z: EN ISO 8765:2022
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 8765:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8765:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 8765:2022
EN ISO 8765
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2022
EUROPÄISCHE NORM
ICS 21.060.10 Supersedes EN ISO 8765:2011
English Version
Fasteners - Hexagon head bolts, with fine pitch thread -
Product grades A and B (ISO 8765:2022)
Fixations - Vis à tête hexagonale partiellement filetées, Mechanische Verbindungselemente -
à pas fin - Grades A et B (ISO 8765:2022) Sechskantschrauben mit Schaft und metrischem
Feingewinde - Produktklassen A und B (ISO
8765:2022)
This European Standard was approved by CEN on 25 September 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8765:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8765:2022
EN ISO 8765:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8765:2022
EN ISO 8765:2022 (E)
European foreword
This document (EN ISO 8765:2022) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2023, and conflicting national standards shall
be withdrawn at the latest by January 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8765:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8765:2022 has been approved by CEN as EN ISO 8765:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8765:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 8765:2022
INTERNATIONAL ISO
STANDARD 8765
Fourth edition
2022-06
Fasteners — Hexagon head bolts, with
fine pitch thread — Product grades A
and B
Fixations — Vis à tête hexagonale partiellement filetées, à pas fin —
Grades A et B
Reference number
ISO 8765:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 8765:2022
ISO 8765:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8765:2022
ISO 8765:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions .2
5 Requirements and reference International Standards . 8
6 Marking and labelling . 9
6.1 Marking on product . . 9
6.2 Labelling on package . 9
7 Designation . 9
Annex A (normative) Dimensions for bolts 8 mm to 14 mm with product grade B .10
Bibliography .11
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 8765:2022
ISO 8765:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 11,
Fasteners with metric external thread, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 185, Fasteners, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 8765:2011), which has been technically
revised.
The main changes are as follows:
— tables for dimensions have been entirely restructured, so that the user can find the specified values
in a reliable manner (no risk of picking the wrong dimension), see Clause 4 and Annex A;
— M18×2 has been added;
— d for M14×1,5 has been corrected to 19,64 mm;
w,min
— the rules for the shortest and greatest standard lengths have been added, and they have been
amended accordingly;
— for steel bolts, property class 5.6 has been deleted and property class 12.9/12.9 has been added;
— for stainless steel bolts, grades D4 and D6 and property class 80 have been added;
— non-ferrous metal bolts have been deleted;
— specifications for marking and labelling have been added as Clause 6.
Any feedback or questions on this document should be directed to the user's national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 8765:2022
INTERNATIONAL STANDARD ISO 8765:2022(E)
Fasteners — Hexagon head bolts, with fine pitch thread —
Product grades A and B
1 Scope
This document specifies the characteristics of hexagon head bolts, in steel and stainless steel, with
metric fine pitch threads M8×1 to M64×4, and with product grades A and B.
If in certain cases other specifications are requested, property classes and stainless steel grades can be
selected from ISO 898-1 or ISO 3506-1, and dimensional options from ISO 888 or ISO 4753.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 262, ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 888, Fasteners — Bolts, screws and studs — Nominal lengths and thread lengths
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs with specified property classes — Coarse thread and fine pitch thread
ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 1891-4, Fasteners — Vocabulary — Part 4: Control, inspection, delivery, acceptance and quality
ISO 3269, Fasteners — Acceptance inspection
ISO 3506-1, Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1:
Bolts, screws and studs with specified grades and property classes
ISO 4042, Fasteners — Electroplated coating systems
ISO 4753, Fasteners — Ends of parts with external ISO metric thread
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
ISO 6157-3, Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements
ISO 8991, Designation system for fasteners
ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coating systems
3 Terms and definitions
No terms and definitions are listed in this document.
1
© ISO 2022 – All rights reserved
---------------------- Page: 11 ----------------------
SIST EN ISO 8765:2022
ISO 8765:2022(E)
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Dimensions
Dimensions shall be in accordance with Figures 1 and 2 and with Tables 1 to 5.
Symbols and descriptions of dimensions are defined in ISO 225.
a
Chamfered end (CH) in accordance with ISO 4753.
b
Incomplete thread u ≤ 2P, where P is the fine pitch specified in Tables 1 to 5.
c
l = l − b and l = l − 5P, where P is the coarse pitch in accordance with ISO 262.
g,max nom s,min g,max
d
Shortest standard length l determined with 5d for thread size 8 mm, 4,5d for 10 mm, 4d for 12 mm to 22 mm,
nom
3,75d for 24 mm to 60 mm, and rounded (if necessary) to the nearest standard length; shortest standard length
l = 220 mm for 64 mm.
nom
e
Greatest standard length l ≤ 10d or 500 mm, whichever is the shorter.
nom
Figure 1 — Hexagon head bolt
Dimensions in millimetres
a) Minimum underhead fillet b) Maximum underhead fillet
a
Reference datum for d .
w
Figure 2 — Head details and permissible shapes
2
© ISO 2022 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 8765:2022
ISO 8765:2022(E)
Table 1 — Dimensions for product grade A – 8 mm to 16 mm
Dimensions in millimetres
a
Thread, d×P M8×1 M10×1,25 (M10×1) M12×1,5 (M12×1,25) (M14×1,5) M16×1,5
b
22 26 26 30 30 34 38
b ref.
c
— — — — — 40 44
max. 0,60 0,60 0,60 0,60 0,60 0,60 0,80
c
min. 0,15 0,15 0,15 0,15 0,15 0,15 0,20
d max. 9,2 11,2 11,2 13,7 13,7 15,7 17,7
a
nom. = max. 8,00 10,00 10,00 12,00 12,00 14,00 16,00
d
s
min. 7,78 9,78 9,78 11,73 11,73 13,73 15,73
d min. 11,63 14,63 14,63 16,63 16,63 19,64 22,49
w
e min. 14,38 17,77 17,77 20,03 20,03 23,36 26,75
nom. 5,3 6,4 6,4 7,5 7,5 8,8 10
k max. 5,45 6,58 6,58 7,68 7,68 8,98 10,18
min. 5,15 6,22 6,22 7,32 7,32 8,62 9,82
k min. 3,61 4,35 4,35 5,12 5,12 6,03 6,87
w
l max. 2 2 2 3 3 3 3
f
r min. 0,4 0,4 0,4 0,6 0,6 0,6 0,6
nom. = max. 13,00 16,00 16,00 18,00 18,00 21,00 24,00
s
min. 12,73 15,73 15,73 17,73 17,73 20,67 23,67
l Range of standard lengths between the stepped bold lines
l
...
SLOVENSKI STANDARD
oSIST prEN ISO 8765:2020
01-september-2020
Vijaki s šestrobo glavo z metrskim drobnim navojem - Razreda izdelave A in B
(ISO/DIS 8765:2020)
Hexagon head bolts with metric fine pitch thread - Product grades A and B (ISO/DIS
8765:2020)
Sechskantschrauben mit Schaft und metrischem Feingewinde - Produktklassen A und B
(ISO/DIS 8765:2020)
Vis à tête hexagonale à filetage métrique à pas fin partiellement filetées - Grades A et B
(ISO/DIS 8765:2020)
Ta slovenski standard je istoveten z: prEN ISO 8765
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
oSIST prEN ISO 8765:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8765:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8765:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8765
ISO/TC 2/SC 11 Secretariat: DIN
Voting begins on: Voting terminates on:
2020-06-25 2020-09-17
Hexagon head bolts with metric fine pitch thread —
Product grades A and B
Vis à tête hexagonale à filetage métrique à pas fin partiellement filetées — Grades A et B
ICS: 21.060.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8765:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8765:2020
ISO/DIS 8765:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8765:2020
ISO/DIS 8765:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 2
5 Requirements and reference International Standards . 8
6 Marking and labelling . 8
7 Designation . 9
Bibliography .10
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 8765:2020
ISO/DIS 8765:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 11,
Fasteners with metric external thread.
This fourth edition cancels and replaces the third edition (ISO 8765:2011), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— tables for dimensions have been entirely restructured, so that the user can find his way around on
a reliable manner (no risk of picking the wrong dimension);
— new size M18×2 has been introduced in Table 2 including all respective dimensions;
— standard lengths have been corrected: addition of l = 90 mm for M24×2, 180 mm for M48×3,
nom
500 mm for M52×4, 240 mm for M64×4 and deletion of l = 440 mm for M42×3;
nom
— d for M14×1,5 was corrected to 19,64 mm;
w,min
— non-ferrous metal bolts have been deleted;
— property class 12.9/12.9 has been added for steel and property class 80 has been added for
stainless steel;
— specificatuions for marking and labelling have been added as Clause 6.
Any feedback or questions on this document should be directed to the user's national standards body. A
complete listing of these bodies can be found at
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.