SIST EN ISO 899-2:2003/A1:2015
(Amendment)Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015)
2011-12-01 EMA: Draft for // ENQ received in ISO/CS (see notification of 2011-12-01 in dataservice).
Kunststoffe - Bestimmung des Kriechverhaltens - Teil 2: Zeitstand-Biegeversuch bei Dreipunkt-Belastung (ISO 899-2:2003/Amd 1:2015)
Plastiques - Détermination du comportement au fluage - Partie 2: Fluage en flexion par mise en charge en trois points (ISO 899-2:2003/Amd 1:2015)
Polimerni materiali – Ugotavljanje lezenja - 2. del: Lezenje pri tritočkovni obremenitvi (ISO 899-2:2003/Amd 1:2015)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2015
3ROLPHUQLPDWHULDOL±8JRWDYOMDQMHOH]HQMDGHO /H]HQMHSULWULWRþNRYQL
REUHPHQLWYL ,62 $PG
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point
loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015)
Kunststoffe - Bestimmung des Kriechverhaltens - Teil 2: Zeitstand-Biegeversuch bei
Dreipunkt-Belastung (ISO 899-2:2003/Amd 1:2015)
Plastiques - Détermination du comportement au fluage - Partie 2: Fluage en flexion par
mise en charge en trois points (ISO 899-2:2003/Amd 1:2015)
Ta slovenski standard je istoveten z: EN ISO 899-2:2003/A1:2015
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 899-2:2003/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 83.080.01
English Version
Plastics - Determination of creep behaviour - Part 2: Flexural
creep by three-point loading - Amendment 1 (ISO 899-
2:2003/Amd 1:2015)
Plastiques - Détermination du comportement au fluage - Kunststoffe - Bestimmung des Kriechverhaltens - Teil 2:
Partie 2: Fluage en flexion par mise en charge en trois Zeitstand-Biegeversuch bei Dreipunkt-Belastung -
points - Amendement 1 (ISO 899-2:2003/Amd 1:2015) Änderung 1 (ISO 899-2:2003/Amd 1:2015)
This amendment A1 modifies the European Standard EN ISO 899-2:2003; it was approved by CEN on 14 February 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 899-2:2003/A1:2015 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 899-1:2003/A1:2015) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This Amendment to the European Standard EN ISO 899:2003 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by September 2015, and conflicting
national standards shall be withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 899-2:2003/Amd 1:2015 has been approved by CEN as EN ISO 899-2:2003/A1:2015 without
any modification.
INTERNATIONAL ISO
STANDARD 899-2
Second edition
2003-06-01
AMENDMENT 1
2015-03-15
Plastics — Determination of creep
behaviour —
Part 2:
Flexural creep by three-point loading
AMENDMENT 1
Plastiques — Détermination du comportement au fluage —
Partie 2: Fluage en flexion par mise en charge en trois points
AMENDEMENT 1
Reference number
ISO 899-2:2003/Amd.1:2015(E)
©
ISO 2015
ISO 899-2:2003/Amd.1:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.