Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery conditions

1.1   This European Standard applies to cold rolled narrow strip in coils and cut lengths in thicknesses up to 10 mm and of widths less than 600 mm, made from low carbon, unalloyed and alloyed steels in accordance with Table 1.
These products are suitable for cold forming. They are also suitable for surface coating. On the other hand, they are not suitable for hardening treatment followed by tempering.
1.2   This European Standard does not cover cold rolled flat products for which a separate standard already exists, particularly the following products:
-   cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10106);
-   grain-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10107);
-   cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341);
-   cold rolled narrow steel strip for heat treatment (EN 10132 1 to −4);
-   cold rolled steel flat products with higher yield strength for cold forming (EN 10268);
-   cold rolled low carbon steel flat products for cold forming (EN 10130);
-   cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel (EN 10205);
-   cold rolled low carbon steel flat products for vitreous enamelling (EN 10209).

Kaltband ohne Überzug aus weichen Stählen zum Kaltumformen - Technische Lieferbedingungen

1.1 Diese Europäische Norm gilt für Kaltband in Rollen in Walzbreiten < 600 mm und daraus durch Ablängen erzeugte Stäbe in Dicken bis 10 mm aus weichen, unlegierten und legierten Stählen nach Tabelle 1.
Die Erzeugnisse sind für das Kaltumformen sowie für eine Oberflächenbehandlung geeignet, nicht aber für das Abschreckhärten und Vergüten.
1.2 Diese Europäische Norm gilt nicht für kaltgewalzte Flacherzeugnisse, für die eigene Normen bestehen, z. B. für folgende Erzeugnisse:
- kaltgewalztes nichtkornorientiertes Elektroblech und  band im schlussgeglühten Zustand (EN 10106);
- kornorientiertes Elektroblech und  band im schlussgeglühten Zustand (EN 10107);
- kaltgewalztes Elektroblech und  band aus unlegierten und legierten Stählen im nicht schlussgeglühten Zustand (EN 10341);
- Kaltband aus Stahl für eine Wärmebehandlung (EN 10132-1 bis EN 10132-4);
- kaltgewalzte Flacherzeugnisse aus Stahl mit hoher Streckgrenze zum Kaltumformen (EN 10268);
- kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Kaltumformen (EN 10130);
- kaltgewalztes Feinstblech in Rollen zur Herstellung von Weißblech oder von elektrolytisch spezial verchromtem Stahl (EN 10205);
- kaltgewalzte Flacherzeugnisse aus weichen Stählen zum Emaillieren (EN 10209).

Feuillards non revêtus laminés à froid en aciers à bas carbone pour formage à froid - Conditions techniques de livraison

1.1   La présente norme européenne est applicable aux feuillards laminés à froid en bobines, et aux feuillards coupés à longueur, d’épaisseur jusqu’à 10 mm et de largeur inférieure à 600 mm, en aciers à bas carbone, non alliés ou alliés conformes au Tableau 1.
Ces produits sont aptes au formage à froid. Ils sont susceptibles également de recevoir un traitement de surface. Par contre, ils ne conviennent pas pour un traitement par trempe suivi d’un revenu.
1.2   La présente norme européenne ne s’applique pas aux produits plats laminés à froid pour lesquels il existe une norme spécifique et en particulier aux produits suivants :
-   Bandes et tôles en acier électrique à grains non orientés laminées à froid et livrées à l'état fini (EN 10106) ;
-   Bandes et tôles en acier électrique à grain orientés livrées à l'état fini (EN 10107) ;
-   Bandes et tôles laminées à froid en acier électrique allié et non allié livrées à l’état semi fini (EN 10341).
-   Feuillards laminés à froid pour traitement thermique (EN 10132-1 à -4) ;
-   Produits plats laminés à froid à haute limite d'élasticité pour formage à froid (EN 10268) ;
-   Produits plats laminés à froid, en acier à bas carbone pour formage à froid (EN 10130) ;
-   Fer noir laminé à froid en bobine destiné à la fabrication de fer blanc ou de fer chromé’’ électrolytique (EN 10205) ;
-   Produits plats laminés à froid, en acier doux pour émaillage par vitrification (EN 10209).

Hladno valjani ozki trakovi iz maloogljičnega (mehkega) jekla za preoblikovanje v hladnem - Tehnični dobavni pogoji

General Information

Status
Published
Publication Date
22-Apr-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-Apr-2020
Due Date
21-Jun-2020
Completion Date
23-Apr-2020

Relations

Buy Standard

Standard
EN 10139:2016+A1:2020
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 10139:2016+A1:2020
01-junij-2020
Hladno valjani ozki trakovi iz maloogljičnega (mehkega) jekla za preoblikovanje v
hladnem - Tehnični dobavni pogoji
Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery
conditions
Kaltband ohne Überzug aus weichen Stählen zum Kaltumformen - Technische
Lieferbedingungen
Feuillards non revêtus laminés à froid en aciers à bas carbone pour formage à froid -
Conditions techniques de livraison
Ta slovenski standard je istoveten z: EN 10139:2016+A1:2020
ICS:
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
SIST EN 10139:2016+A1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 10139:2016+A1:2020

---------------------- Page: 2 ----------------------
SIST EN 10139:2016+A1:2020


EN 10139:2016+A1
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2020
EUROPÄISCHE NORM
ICS 77.140.50
English Version

Cold rolled uncoated low carbon steel narrow strip for
cold forming - Technical delivery conditions
Feuillards non revêtus laminés à froid en aciers à bas Kaltband ohne Überzug aus weichen Stählen zum
carbone pour formage à froid - Conditions techniques Kaltumformen - Technische Lieferbedingungen
de livraison
This European Standard was approved by CEN on 13 December 2015 and includes Amendment 1 approved by CEN on 4
February 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10139:2016+A1:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 10139:2016+A1:2020
EN 10139:2016+A1:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Classification and designation . 5
5 Designation. 5
6 Properties . 6
6.1 Steel making process and chemical composition . 6
6.2 Choice of properties . 6
6.3 Mechanical and technological properties . 6
6.4 Surface characteristics . 6
6.4.1 General . 6
6.4.2 Surface appearance . 7
6.4.3 Surface finish . 7
6.5 Stretcher strain marks . 7
6.6 Suitability for the application of surface coating . 7
6.7 Weldability . 8
6.8 Dimensions, mass, permissible tolerances . 8
7 Testing . 8
7.1 Agreement on acceptance testing . 8
7.2 Acceptance units and number of tests . 8
7.3 Sampling and preparation of test pieces . 9
7.4 Test methods to be followed . 9
7.5 Re-tests . 9
8 Marking . 9
9 Oiling . 9
10 Packing . 10
11 Information to be supplied by the purchaser . 10
12 Disputes . 10

2

---------------------- Page: 4 ----------------------
SIST EN 10139:2016+A1:2020
EN 10139:2016+A1:2020 (E)
European foreword
This document (EN 10139:2016+A1:2020) has been prepared by Technical Committee ECISS/TC 109
“Coated and uncoated flat products to be used for cold forming”, the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes !EN 10139:2016".
This document includes Amendment 1 approved by CEN on 2020-02-13.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 10139:2016+A1:2020
EN 10139:2016+A1:2020 (E)
1 Scope
1.1 This European Standard applies to cold rolled narrow strip in coils and cut lengths in thicknesses
up to 10 mm and of widths less than 600 mm, made from low carbon, unalloyed and alloyed steels in
accordance with Table 1.
These products are suitable for cold forming. They are also suitable for surface coating. On the other
hand, they are not suitable for hardening treatment followed by tempering.
1.2 This European Standard does not cover cold rolled flat products for which a separate standard
already exists, particularly the following products:
— cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state
(EN 10106);
— grain-oriented electrical steel sheet and strip delivered in the fully processed state (EN 10107);
— cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state
(EN 10341);
— cold rolled narrow steel strip for heat treatment (EN 10132-1 to −4);
— cold rolled steel flat products with higher yield strength for cold forming (EN 10268);
— cold rolled low carbon steel flat products for cold forming (EN 10130);
— cold reduced blackplate in coil form for the production of tinplate or electrolytic
chromium/chromium oxide coated steel (EN 10205);
— cold rolled low carbon steel flat products for vitreous enamelling (EN 10209).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 10020, Definition and classification of grades of steel
EN 10021, General technical delivery conditions for steel products
EN 10027-1, Designation systems for steels - Part 1: Steel names
EN 10027-2, Designation systems for steels - Part 2: Numerical system
EN 10049, Measurement of roughness average Ra and peak count RPc on metallic flat products
EN 10079, Definition of steel products
EN 10140:2006, Cold rolled narrow steel strip - Tolerances on dimensions and shape
EN 10204, Metallic products - Types of inspection documents
4

---------------------- Page: 6 ----------------------
SIST EN 10139:2016+A1:2020
EN 10139:2016+A1:2020 (E)
EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical
testing (ISO 377:2013, Corrected version 2015-06-01)
EN ISO 6507 (all parts), Metallic materials — Vickers hardness test (ISO 6507)
EN ISO 6892-1:2009, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO
6892-1:2009)
ISO 10113, Metallic materials — Sheet and strip — Determination of plastic strain ratio
ISO 10275, Metallic materials — Sheet and strip — Determination of tensile strain hardening exponent
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10079 apply.
4 Classification and designation
4.1 This European Standard specifies the grades listed in Table 1. In the case of steel grade DC01, the
deoxidation method shall be left to the manufacturer’s discretion. Steel grades DC03, DC04, DC05, DC06
and DC07 shall be supplied fully killed.
4.2 Products manufactured from these steels may be ordered and supplied in different delivery
conditions (see Table 1) and with different surface characteristics (see 6.4 and Table 2).
4.3 For the purposes of the specifications of this European Standard, the selection of steel grade,
delivery condition and surface characteristics are of the responsibility of the purchaser.
NOTE 1 In case of narrow widths, strip complying with this European Standard can also be wound in layers
and supplied in the form of a bobbin wound coil.
NOTE 2 After uncoiling and shearing, strip can be supplied in cut lengths.
5 Designation
The symbol designation of the steel grades in this European Standard is in accordance with EN 10027-1
and the numerical designation is allocated in accordance with EN 10027-2.
The standard designation consists of the words narrow strip or cut lengths, followed in order by
!reference to European Standard EN 10140:2006 and the nominal dimensions of the product and for
the steel grade":
a) reference to this European Standard, EN 10139;
b) the symbol DC, followed by the grade designation (01, 03, 04, 05, 06 and 07);
c) the symbol for delivery condition (see Table 1);
d) the symbol for surface appearance (MA, MB or MC, see Table 2);
e) the symbol for surface finish where appropriate (RN, RL, RM or RR, see 6.4.3 and Table 2).
5

---------------------- Page: 7 ----------------------
SIST EN 10139:2016+A1:2020
EN 10139:2016+A1:2020 (E)
EXAMPLE 1 Designation of cold rolled narrow strip, 1,50 mm thick, having a normal tolerance on the nominal
thickness, a width of 200 mm, having a normal tolerance on the nominal width, slit edges (GK) and made from
steel grade DC04, in a lightly skin-passed condition (LC) with a smooth and uniform surface appearance (MB) and
a “matt” surface finish (RM):
Narrow strip EN 10140:2006 ― 1,50 × 200 ― GK
Steel EN 10139 ― DC04 + LC ― MB ― RM
EXAMPLE 2 Designation of cold rolled narrow strip, 2,00 mm thick, having a normal tolerance on the nominal
thickness, a width of 450 mm, having a normal tolerance on the nominal width, slit edges (GK) and made from
steel grade DC03, in the annealed condition (A), with a bright, metallically clean surface appearance (MA) and a
smooth surface finish (RL):
Narrow strip EN 10140:2006 ― 2,00 × 450 ― GK
Steel EN 10139 ― DC03 + A ― MA ― RL
6 Properties
6.1 Steel making process and chemical composition
6.1.1 The steel making process shall be left to the discretion of the manufacturer.
6.1.2 The chemical composition based on ladle analysis shall be as given in Table 1.
6.2 Choice of properties
The products covered by this European Standard shall comply with the specifications given in Table 1.
If agreed separately, they may be supplied with a special suitability for making a particular part; in this
case, a maximum percentage of processing scrap may be fixed by common agreement and acceptance
tests on the basis of the mechanical properties shall not apply.
6.3 Mechanical and technological properties
6.3.1 The mechanical and technological properties of the products are given in Table 1. These
properties are guaranteed for the periods specified in Table 1 with effect from the date that the
products are made available for delivery. The purchaser shall be informed of this date when the
products are to be made available, with a warning appropriate to the guarantee of mechanical
properties. Storage of grade DC01 products for more than 3 months may cause a change in the
mechanical properties likely to give rise to a reduction in the suitability for forming and drawing.
6.3.2 The usual test for checking the mechanical properties given in Table 1 is the tensile test.
However, if agreed at the time of ordering, hardness values may be specified instead of tensile test
properties, but not both.
6.3.3 The tensile test values shall apply to longitudinal test pieces.
6.4 Surface characteristics
6.4.1 Gen
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.