Abstract

This document specifies the measurement of setting time of a prepared cementitious or calcium sulfate-based floor levelling compound, after mixing with the liquid component, e.g. water.
This document applies to cementitious and calcium sulfate-based floor levelling compounds used for the preparation of subfloors to ensure the suitability of the substrate prior to the installation of floor coverings. By using the floor levelling compound, a homogeneous layer is built up on the load-bearing substrate, to ensure consistent absorbency, evenness and strength.

Status
Not Published
Public Enquiry End Date
29-Apr-2026
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
17-Nov-2026
Due Date
05-Jan-2027
Completion Date
17-Nov-2026

Buy Documents

Draft

oSIST prEN 13409:2026

English language (8 pages)
Preview
Preview
e-Library read for
×1 day

kSIST FprEN 13409:2026 is the Slovene adoption of prEN 13409:2026 from CEN. It specifies a laboratory method for determining the setting time of cementitious and calcium sulfate-based floor levelling compounds after mixing with the liquid component, such as water. The document is used by laboratories, manufacturers, and quality teams that need to check how quickly a levelling compound starts and finishes setting before it is used on subfloors for floor coverings.

What does kSIST FprEN 13409:2026 specify?

kSIST FprEN 13409:2026 specifies one test method: measuring the setting time of a prepared cementitious or calcium sulfate-based floor levelling compound after it has been mixed with its liquid component. It applies to compounds used to prepare subfloors so the substrate is suitable before floor coverings are installed.

The document is organized into nine main clauses:

  • Clause 1 - Scope
  • Clause 2 - Normative references
  • Clause 3 - Terms and definitions
  • Clause 4 - Principle
  • Clause 5 - Standard test conditions
  • Clause 6 - Apparatus and materials
  • Clause 7 - Procedure
  • Clause 8 - Expression of results
  • Clause 9 - Test report

This structure takes the reader from the test purpose, to the equipment and environment, and then to the measurement and reporting steps.

What are the key requirements of kSIST FprEN 13409:2026?

The standard’s core requirement is a controlled Vicat-needle penetration test. Clause 4 says the setting time is determined by observing how far a needle penetrates the compound after mixing, then recording the time linked to a specified penetration value.

Test conditions and preparation

Clause 5 requires standard test conditions of 23 °C ± 2 °C and 50 % ± 5 % relative humidity, in line with ISO 554. It also requires the test materials and apparatus to be stored under those conditions during the test, and the test area to have air circulation below 0.2 m/s. In practice, this limits environmental effects that could change setting behaviour.

Clause 7 requires the compound to be mixed according to prEN 1937:2026 before the test starts. That matters because the measured setting time depends on a consistent mixing procedure.

Apparatus and calibration

Clause 6 specifies a Vicat apparatus in accordance with EN 196-3, with a steel needle of defined size and a total moving mass of 300 g ± 1 g. It also specifies a mould of hard rubber with a truncated conical shape and a glass plate beneath it. Alternative mould materials or shapes are allowed only if they can be shown to give the same results as the specified mould. This means the test is strict about geometry, because the needle penetration depends on it.

Clause 7.1 requires calibration of the Vicat apparatus before the test. The needle is lowered onto the base plate, the pointer is set to zero, and the needle is returned to the stand-by position. That step verifies that the starting point of the measurement is correct.

Initial and final setting time

Clause 7.2 defines the initial setting time procedure. The mould is filled immediately after mixing, the surface is levelled, and the needle is applied at repeated time intervals until the scale reading reaches 4 mm ± 1 mm. The time is then recorded to the nearest minute. In practice, this marks when the material has progressed far enough in setting that the needle can no longer penetrate to the earlier depth.

Clause 7.3 covers the final setting time. The test continues until the needle penetrates only 0.5 mm, and that time is also recorded to the nearest minute. This gives a second point in the setting process, useful for comparing products or batch performance.

Reporting

Clause 8 requires both setting times to be expressed as elapsed time from the end of mixing, rounded to the nearest minute. Clause 9 requires the test report to identify the material, the liquid proportion, the mixing method and duration, the initial and final setting times, any deviations, and the test date. That gives the result enough context to be traced and compared.

What terms does kSIST FprEN 13409:2026 define?

  • Setting - the transition of the material from plastic to solid state.
  • Initial setting time - the time point linked to the first specified penetration result, used to show the early stage of stiffening.
  • Final setting time - the time point when the needle first penetrates only 0.5 mm, showing the end stage of setting.
  • Vicat apparatus - the penetration instrument used in the test, with the specified needle and moving mass.
  • Standard test conditions - the controlled temperature, humidity, and air movement required for the test.
  • prEN 1937:2026 - the companion draft used for the standard mixing procedure and the floor levelling compound and liquid.
  • EN 196-3 - the referenced standard that provides the Vicat apparatus basis used in this method.
  • ISO 554 - the reference for the atmosphere conditions used during conditioning and testing.

Who uses kSIST FprEN 13409:2026?

kSIST FprEN 13409:2026 is used by testing laboratories that measure setting time for product characterization or verification. Manufacturers of cementitious and calcium sulfate-based floor levelling compounds use it for development and batch control.

Quality managers and buyers use the results when they need evidence that a product sets within expected limits before floor coverings are installed. It is also relevant to teams preparing subfloors, because the measured setting behaviour affects when the layer can be handled or assessed further.

What changed in kSIST FprEN 13409:2026 from the previous edition?

kSIST FprEN 13409:2026 will supersede EN 13409:2002. The European foreword states three changes:

  • the former term “hydraulic setting floor smoothing and/or levelling compounds” has been replaced with “cementitious and calciumsulfate-based floor levelling compounds”
  • the scope has been made more specific
  • editorial changes have been made

Which standards are used with kSIST FprEN 13409:2026?

  • EN 196-3 - provides the Vicat apparatus basis and the setting-time equipment referenced by the method.
  • EN 923 - supplies terms and definitions used in the adhesives field.
  • prEN 1937:2026 - provides the standard mixing procedures and identifies the floor levelling compound and liquid used in the test.
  • ISO 554 - specifies the standard atmospheres used for conditioning and testing.

What does the kSIST FprEN 13409:2026 document contain?

The document contains a principle for measuring setting time by needle penetration, followed by the required test conditions, apparatus, and step-by-step procedure. It includes calibration instructions, the procedure for determining initial setting time, and the procedure for determining final setting time.

It also sets out how to express the results and what must be included in the test report. Figure 1 shows the Vicat apparatus and needle arrangement used for the measurements.

Relations

Effective Date
08-May-2024

Buy Documents

Draft

oSIST prEN 13409:2026

English language (8 pages)
Preview
Preview
e-Library read for
×1 day

Get Certified

Connect with accredited certification bodies for this standard

DIBt (Deutsches Institut für Bautechnik)

German Institute for Building Technology.

DAKKS Germany Verified

DIN CERTCO

DIN Group product certification.

DAKKS Germany Verified

Aboma Certification B.V.

Specialized in construction, metal, and transport sectors.

RVA Netherlands Verified

Sponsored listings

Frequently Asked Questions

kSIST FprEN 13409:2026 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Adhesives - Test method for cementitious and calciumsulfate-based floor levelling compounds - Determination of setting time". This standard covers: This document specifies the measurement of setting time of a prepared cementitious or calcium sulfate-based floor levelling compound, after mixing with the liquid component, e.g. water. This document applies to cementitious and calcium sulfate-based floor levelling compounds used for the preparation of subfloors to ensure the suitability of the substrate prior to the installation of floor coverings. By using the floor levelling compound, a homogeneous layer is built up on the load-bearing substrate, to ensure consistent absorbency, evenness and strength.

This document specifies the measurement of setting time of a prepared cementitious or calcium sulfate-based floor levelling compound, after mixing with the liquid component, e.g. water. This document applies to cementitious and calcium sulfate-based floor levelling compounds used for the preparation of subfloors to ensure the suitability of the substrate prior to the installation of floor coverings. By using the floor levelling compound, a homogeneous layer is built up on the load-bearing substrate, to ensure consistent absorbency, evenness and strength.

kSIST FprEN 13409:2026 is classified under the following ICS (International Classification for Standards) categories: 91.100.99 - Other construction materials. The ICS classification helps identify the subject area and facilitates finding related standards.

kSIST FprEN 13409:2026 has the following relationships with other standards: It is inter standard links to SIST EN 13409:2002. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

kSIST FprEN 13409:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
oSIST prEN 13409:2026
01-april-2026
Lepila - Preskusna metoda za cementne in kalcijsulfatne izravnalne mase za tla -
Ugotavljanje strjevalnega časa
Adhesives - Test method for cementitious and calciumsulfate-based floor levelling
compounds - Determination of setting time
Klebstoffe - Prüfverfahren für zement- und calciumsulfatbasierte Bodenspachtelmassen -
Bestimmung der Abbindezeit
Adhésifs - Méthode d’essai pour les mortiers de nivellement à base de ciment et de
sulfate de calcium - Détermination du temps de prise
Ta slovenski standard je istoveten z: prEN 13409
ICS:
91.100.99 Drugi gradbeni materiali Other construction materials
oSIST prEN 13409:2026 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 13409:2026
oSIST prEN 13409:2026
DRAFT
EUROPEAN STANDARD
prEN 13409
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2026
ICS 91.100.99 Will supersede EN 13409:2002
English Version
Adhesives - Test method for cementitious and
calciumsulfate-based floor levelling compounds -
Determination of setting time
Adhésifs - Méthode d'essai pour les mortiers de Klebstoffe - Prüfverfahren für zement- und
nivellement à base de ciment et de sulfate de calcium - calciumsulfatbasierte Bodenspachtelmassen -
Détermination du temps de prise Bestimmung der Abbindezeit
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 193.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13409:2026 E
worldwide for CEN national Members.

oSIST prEN 13409:2026
prEN 13409:2026 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Standard test conditions . 5
6 Apparatus and materials . 6
7 Procedure . 6
7.1 Calibration . 6
7.2 Determination of initial setting time . 6
7.3 Determination of final setting time . 7
8 Expression of results . 8
9 Test report . 8

oSIST prEN 13409:2026
prEN 13409:2026 (E)
European foreword
This document (prEN 13409:2026) has been prepared by Technical Committee CEN/TC 193 “Adhesives”,
the secretariat of which is held by UNE.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13409:2002.
prEN 13409:2026 includes the following significant technical changes with respect to EN 13409:2002:
— term “hydraulic setting floor smoothing and/or levelling compounds” changed to “cementitious and
calciumsulfate-based floor levelling compounds”;
— concretisation of the scope;
— editorial changes.
oSIST prEN 13409:2026
prEN 13409:2026 (E)
Introduction
Persons using this document are to be familiar with normal laboratory practice.
This document does not purport to address all the safety problems, if any, associated with its use.
It is the responsibility of the user to establish health and safety practices and to ensure compliance with
any European and national regulatory conditions.
oSIST prEN 13409:2026
prEN 13409:2026 (E)
1 Scope
This document specifies the measurement of setting time of a prepared cementitious or calcium sulfate-
based floor levelling compound, after mixing with the liquid compon
...