SIST EN 60598-2-5:2016

Luminaires - Part 2-5: Particular requirements - Floodlights (IEC 60598-2-5:2015)

This part of IEC 60598 specifies requirements for floodlights for use with electrical light
sources on supply voltages not exceeding 1 000 V.

Leuchten - Teil 2-5: Besondere Anforderungen - Scheinwerfer

Luminaires - Partie 2-5: Exigences particulières - Projecteurs

L'IEC 60598-2-5:2015 spécifie les exigences relatives aux projecteurs destinés à être utilisés avec des sources lumineuses électriques dont la tension d'alimentation ne dépasse pas 1 000 V.
Cette troisième édition annule et remplace la deuxième édition parue en 1998 et constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: elle introduit des exigences concernant l'essai de bris du verre.

Svetilke - 2-5. del: Posebne zahteve - Žarometi in sojniki (IEC 60598-2-5:2015)

Ta del standarda IEC 60598 določa zahteve za žaromete za uporabo z električnimi svetlobnimi viri, namenjenimi za delovanje z omrežnim napajanjem do 1000 V.

General Information

• Status: Published
• Publication Date: 08-Feb-2016
• ICS: 29.140.40 - Luminaires
• Technical Committee: IESV - Lamps and related equipment
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 26-Nov-2015
• Due Date: 31-Jan-2016
• Completion Date: 09-Feb-2016
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Ref Project: EN 60598-2-5:2015 - Luminaires - Part 2-5: Particular requirements - Floodlights

Relations

• Replaces: SIST EN 60598-2-5:1999 - Luminaires - Part 2-5: Particular requirements - Floodlights
• Effective Date: 04-Feb-2014
• Replaces: SIST EN 60598-2-5:1999 - Luminaires - Part 2-5: Particular requirements - Floodlights
• Effective Date: 28-Jan-2023
• Revised: SIST EN 60598-2-5:1999 - Luminaires - Part 2-5: Particular requirements - Floodlights
• Effective Date: 06-May-2014

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60598-2-5:2016
01-april-2016
1DGRPHãþD
SIST EN 60598-2-5:1999
Svetilke - 2-5. del: Posebne zahteve - Žarometi in sojniki (IEC 60598-2-5:2015)
Luminaires - Part 2-5: Particular requirements - Floodlights (IEC 60598-2-5:2015)
Ta slovenski standard je istoveten z: EN 60598-2-5:2015
ICS:
29.140.40 Svetila Luminaires
SIST EN 60598-2-5:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60598-2-5:2016

---------------------- Page: 2 ----------------------

SIST EN 60598-2-5:2016


EUROPEAN STANDARD EN 60598-2-5

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2015
ICS 29.140.40 Supersedes EN 60598-2-5:1998
English Version
Luminaires - Part 2-5: Particular requirements - Floodlights
(IEC 60598-2-5:2015)
Luminaires - Partie 2-5: Exigences particulières - Leuchten - Teil 2: Besondere Anforderungen -
Projecteurs Hauptabschnitt 5: Scheinwerfer
(IEC 60598-2-5:2015) (IEC 60598-2-5:2015)
This European Standard was approved by CENELEC on 2015-09-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60598-2-5:2015 E

---------------------- Page: 3 ----------------------

SIST EN 60598-2-5:2016
EN 60598-2-5:2015
European foreword
The text of document 34D/1172/FDIS, future edition 3 of IEC 60598-2-5, prepared by IEC/SC 34D
"Luminaires" of IEC/TC 34 "Lamps and related equipment" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN 60598-2-5:2015.
The following dates are fixed:
• latest date by which the document has (dop) 2016-06-10
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-09-10
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60598-2-5:1999 + corr. Dec. 1998.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).
Endorsement notice
The text of the International Standard IEC 60598-2-5:2015 was approved by CENELEC as a
European Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 60598-2-5:2016
EN 60598-2-5:2015

Annex ZA
(normative)


Normative references to international publications
with their corresponding European publications


The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.


NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.


Publication Year Title EN/HD Year
IEC 60068-2-75 -  Environmental testing - Part 2-75: Tests - EN 60068-2-75 -
Test Eh: Hammer tests
IEC 60598-1 -  Luminaires -- Part 1: General requirements EN 60598-1 -
and tests
IEC 62262 -  Degrees of protection provided by EN 62262 -
enclosures for electrical equipment against
external mechanical impacts (IK code)

3

---------------------- Page: 5 ----------------------

SIST EN 60598-2-5:2016

---------------------- Page: 6 ----------------------

SIST EN 60598-2-5:2016



IEC 60598-2-5

®


Edition 3.0 2015-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Luminaires –

Part 2-5: Particular requirements – Floodlights




Luminaires –

Partie 2-5: Exigences particulières – Projecteurs
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.140.40 ISBN 978-2-8322-2821-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60598-2-5:2016
– 2 – IEC 60598-2-5:2015 © IEC 2015
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
5.1 Scope . 6
5.2 Normative references . 6
5.3 Terms and definitions . 6
5.4 Classification of Iuminaires . 6
5.5 Marking . 7
5.6 Construction . 7
5.7 Creepage distances and clearances . 10
5.8 Provision for earthing . 10
5.9 Terminals . 10
5.10 External and internal wiring . 10
5.11 Protection against electric shock . 10
5.12 Endurance tests and thermal tests . 10
5.13 Resistance to dust and moisture . 11
5.14 Insulation resistance and electric strength . 11
5.15 Resistance to heat, fire and tracking . 11
Annex A (informative) Schedule of amended clauses containing more serious/critical

requirements which require products to be retested . 12

Figure 1 – Counting particles at the edge of the square . 9

---------------------- Page: 8 ----------------------

SIST EN 60598-2-5:2016
IEC 60598-2-5:2015 © IEC 2015 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

LUMINAIRES –

Part 2-5: Particular requirements – Floodlights

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60598-2-5 has been prepared by subcommittee 34D: Luminaires, of
IEC technical committee 34: Lamps and related equipment.
This third edition cancels and replaces the second edition published in 1998, and constitutes a
technical revision.
This edition includes the following significant technical changes with respect to the previous
edition: it introduces requirements for the glass breaking test.

---------------------- Page: 9 ----------------------

SIST EN 60598-2-5:2016
– 4 – IEC 60598-2-5:2015 © IEC 2015
The text of this standard is based on the following documents:
FDIS Report on voting
34D/1172/FDIS 34D/1180/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This standard is to be read in conjunction with IEC 60598-1: Luminaires – Part 1: General
requirements and tests.
A list of all the parts in the IEC 60598 series, published under the general title Luminaires can
be found on the IEC website.
NOTE In this standard, the following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------

SIST EN 60598-2-5:2016
IEC 60598-2-5:2015 © IEC 2015 – 5 –
INTRODUCTION
The mechanical stress on floodlights is similar to the mechanical stress on
...