Lamp controlgear - Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)

This part of IEC 61347 specifies particular safety requirements for battery supplied electronic
controlgear for maintained and non-maintained emergency lighting purposes.
It includes specific requirements for electronic controlgear and control units for self-contained
luminaires for emergency lighting as specified by IEC 60598-2-22.
It is intended for controlgear for fluorescent lamps, but it is also applicable to other lamp types
e.g. incandescent, high pressure discharge lamps and LEDs.
This standard covers the emergency mode operation of a controlgear. For controlgear with a
combination of normal and emergency lighting operation, the normal lighting operation
aspects are covered by the appropriate part 2 of IEC 61347.
DC supplied electronic controlgear for emergency lighting may or may not include batteries.
This standard also includes operational requirements for electronic controlgear, which, in the
case of d.c. supplied electronic controlgear, are regarded as performance requirements. This
is because non-operational emergency lighting equipment presents a safety hazard. It does
not apply to d.c. supplied electronic controlgear for emergency lighting, which are intended for
connection to a centralised emergency power supply system. A centralised emergency power
system could be a central battery system.
NOTE Annex J of IEC 61347-2-3 applies to a.c., a.c./d.c. or d.c. supplied electronic controlgear for connection to
centralised emergency power supply systems that are also intended for emergency lighting operations from
a.c./d.c. supplies.

Geräte für Lampen - Teil 2-7: Besondere Anforderungen an batterieversorgte elektronische Betriebsgeräte für die Notbeleuchtung (mit Einzelbatterie)

Appareillages de lampes - Partie 2-7: Règles particulières relatives aux appareillages électroniques alimentés par batterie pour l'éclairage de secours (autonome)

La CEI 61347-2-7:2011 spécifie les exigences particulières de sécurité pour les appareillages électroniques alimentés par batterie prévus pour l'éclairage de secours permanent ou non permanent. Elle comprend des exigences particulières relatives aux appareillages électroniques et aux blocs de commande pour les blocs autonomes d'éclairage de secours spécifiés dans la CEI 60598-2-22. Cette troisième édition annule et remplace la deuxième édition parue en 2006. Elle constitue une révision technique. Les changements significatifs introduits dans cette troisième édition incluent: - des modifications de la CEI 61347-2-7 en vue de devenir une norme exclusivement relative aux appareillages électroniques alimentés par batterie en courant continu pour l'éclairage de secours (autonome). La CEI 61347-2-3, Annexe J, est destinée à couvrir les appareillages de secours à alimentation centrale; - la mise à jour de l'Article 22 - Dispositifs de recharge; - la modification de l'Article 20, caractérisation de la tension de la batterie pour étayer la mesure de l'EBLF. Il s'agit de simplifier et d'accroître la reproductibilité des essais; - la rationalisation des exigences de la CEI 61347-2-7 avec la CEI 60598-2-22, les exigences de la CEI 60598-2-2 étant transférées à la CEI 61347-2-7. Cette publication doit être lue conjointement avec la .>

Stikalne naprave za sijalke - 2-7. del: Posebne zahteve za enosmerno napajane elektronske predstikalne naprave za nujnostno razsvetljavo

Ta del standarda IEC 61347 določa posebne varnostne zahteve za enosmerno napajane elektronske predstikalne naprave za vzdrževano in nevzdrževano nujnostno razsvetljavo. Zajema posebne zahteve za elektronske predstikalne naprave in nadzorne enote za samostojne svetilke za nujnostno razsvetljavo iz standarda IEC 60598-2-22. Standard je namenjen stikalnim napravam za fluorescenčne sijalke, vendar se uporablja tudi za druge vrste sijalk, npr. visokotlačne sijalke z žarilno nitko in svetleče diode. Ta standard zajema nujnostno delovanje stikalnih naprav. Vidiki običajne razsvetljave za stikalne naprave s kombinacijo običajne in nujnostne razsvetljave so zajeti v ustreznem 2. delu standarda IEC 61347. Enosmerno napajane elektronske predstikalne naprave za nujnostno razsvetljavo lahko vključujejo akumulatorje ali ne. Ta standard zajema tudi operativne zahteve za elektronske predstikalne naprave, ki se v primeru enosmerno napajanih elektronskih predstikalnih naprav štejejo za zahteve glede zmogljivosti. Razlog za to je, da nedelujoča oprema za nujnostno razsvetljavo pomeni varnostno tveganje. Standard se ne uporablja za enosmerno napajane elektronske predstikalne naprave za nujnostno razsvetljavo, ki so namenjene za povezavo s centraliziranim zasilnim napajalnim sistemom. Centralizirani zasilni napajalni sistem je lahko osrednji akumulatorski sistem.

General Information

Status
Published
Publication Date
10-Apr-2012
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
27-Mar-2012
Due Date
01-Jun-2012
Completion Date
11-Apr-2012

RELATIONS

Buy Standard

Standard
SIST EN 61347-2-7:2012 - BARVE na pdf strani 40
English language
39 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 61347-2-7:2012
01-maj-2012
Stikalne naprave za sijalke - 2-7. del: Posebne zahteve za enosmerno napajane
elektronske predstikalne naprave za nujnostno razsvetljavo

Lamp controlgear - Part 2-7: Particular requirements for battery supplied electronic

controlgear for emergency lighting (self-contained)
Geräte für Lampen - Teil 2-7: Besondere Anforderungen an batterieversorgte
elektronische Betriebsgeräte für die Notbeleuchtung (mit Einzelbatterie)

Appareillages de lampes - Partie 2-7: Règles particulières relatives aux appareillages

électroniques alimentés par batterie pour l'éclairage de secours (autonome)
Ta slovenski standard je istoveten z: EN 61347-2-7:2012
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
SIST EN 61347-2-7:2012 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 61347-2-7:2012
---------------------- Page: 2 ----------------------
SIST EN 61347-2-7:2012
EUROPEAN STANDARD
EN 61347-2-7
NORME EUROPÉENNE
March 2012
EUROPÄISCHE NORM
ICS 29.140.99 Supersedes EN 61347-2-7:2006
English version
Lamp controlgear -
Part 2-7: Particular requirements for battery supplied electronic
controlgear for emergency lighting (self-contained)
(IEC 61347-2-7:2011)
Appareillages de lampes - Geräte für Lampen -
Partie 2-7: Règles particulières relatives Teil 2-7: Besondere Anforderungen an
aux appareillages électroniques alimentés batterieversorgte elektronische

par batterie pour l'éclairage de secours Betriebsgeräte für die Notbeleuchtung (mit

(autonome) Einzelbatterie)
(CEI 61347-2-7:2011) (IEC 61347-2-7:2011)

This European Standard was approved by CENELEC on 2012-01-11. CENELEC members are bound to comply

with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and notified

to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,

the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61347-2-7:2012 E
---------------------- Page: 3 ----------------------
SIST EN 61347-2-7:2012
EN 61347-2-7:2012 - 2 -
Foreword

The text of document 34C/995/FDIS, future edition 3 of IEC 61347-2-7, prepared by SC 34C, "Auxiliaries

for lamps", of IEC/TC 34, "Lamps and related equipment" was submitted to the IEC-CENELEC parallel

vote and approved by CENELEC as EN 61347-2-7:2012.
The following dates are fixed:
(dop) 2012-10-11
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-01-11
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61347-2-7:2006.

EN 61347-2-7:2012 includes the following significant technical changes with respect to EN 61347-2-

7:2006:

 modification of EN 61347-2-7 to become a standard exclusively for d.c. battery supplied electronic

controlgear for emergency lighting (self-contained). EN 61347-2-3:2011, Annex J, is intended to cover

centrally supplied emergency controlgear;
 update of Clause 22 – Recharging devices;

 modification of Clause 20 battery voltage characterisation to support EBLF measurement. This to

simplify and increase reproducibility of testing;

 rationalisation of requirements between EN 61347-2-7 and EN 60598-2-22, requirements of

EN 60598-2-22 being transferred to EN 61347-2-7.

This standard shall be used in conjunction with EN 61347-1:2008 + A1:2011 + A2:200X .

This part 2 supplements or modifies the corresponding clauses in EN 61347-1.
NOTE In this standard, the following print types are used:
– requirements: in roman type.
– test specifications: in italic type.
– notes: in small roman type.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent

rights.
Endorsement notice

The text of the International Standard IEC 61347-2-7:2011 was approved by CENELEC as a European

Standard without any modification.
To be published.
---------------------- Page: 4 ----------------------
SIST EN 61347-2-7:2012
- 3 - EN 61347-2-7:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD

applies.
Publication Year Title EN/HD Year
IEC 60081 - Double-capped fluorescent lamps - EN 60081 -
Performance specifications
IEC 60598-2-22 - Luminaires - EN 60598-2-22 -
Part 2-22: Particular requirements -
Luminaires for emergency lighting
IEC 60901 - Single-capped fluorescent lamps - EN 60901 -
Performance specifications
IEC 60921 - Ballasts for tubular fluorescent lamps - EN 60921 -
Performance requirements
IEC 60929 - AC and/or DC-supplied electronic control gear EN 60929 -
for tubular fluorescent lamps - Performance
requirements
IEC 61347-1 - Lamp controlgear - EN 61347-1 -
Part 1: General and safety requirements
IEC 61347-2-3 - Lamp controlgear - EN 61347-2-3 -
Part 2-3: Particular requirements for a.c.
and/or d.c. supplied electronic control gear for
fluorescent lamps
IEC 61558-1 2005 Safety of power transformers, power supplies, EN 61558-1 2005
+ corr. March 2010 reactors and similar products - + corr. August 2006
+ corr. March 2008 Part 1: General requirements and tests + A1 2009
+ A1 2009

IEC 61558-2-1 2007 Safety of power transformers, power supplies, EN 61558-2-1 2007

reactors and similar products -
Part 2-1: Particular requirements and tests for
separating transformers and power supplies
incorporating separating transformers for
general applications

IEC 61558-2-6 2009 Safety of transformers, reactors, power supply EN 61558-2-6 2009

units and similar products for supply voltages
up to 1 100 V -
Part 2-6: Particular requirements and tests for
safety isolating transformers and power
supply units incorporating safety isolating
transformers

IEC 61558-2-16 2009 Safety of transformers, reactors, power supply EN 61558-2-16 2009

units and similar products for voltages up to
1 100 V -
Part 2-16: Particular requirements and tests
for switch mode power supply units and
transformers for switch mode power supply
units
---------------------- Page: 5 ----------------------
SIST EN 61347-2-7:2012
EN 61347-2-7:2012 - 4 -
Publication Year Title EN/HD Year
IEC 62034 - Automatic test system for battery powered EN 62034 -
emergency escape lighting
---------------------- Page: 6 ----------------------
SIST EN 61347-2-7:2012
IEC 61347-2-7
Edition 3.0 2011-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Lamp controlgear –

Part 2-7: Particular requirements for battery supplied electronic controlgear for

emergency lighting (self-contained)
Appareillages de lampes –
Partie 2-7: Règles particulières relatives aux appareillages électroniques
alimentés par batterie pour l’éclairage de secours (autonome)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX V
ICS 29.140.99 ISBN 978-2-88912-830-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 61347-2-7:2012
– 2 – 61347-2-7 © IEC:2011
CONTENTS

FOREWORD ........................................................................................................................... 4

INTRODUCTION ..................................................................................................................... 6

1 Scope ............................................................................................................................... 7

2 Normative references ....................................................................................................... 7

3 Terms and definitions ....................................................................................................... 8

4 General requirements ....................................................................................................... 9

5 General notes on tests ................................................................................................... 10

6 Classification .................................................................................................................. 10

7 Marking .......................................................................................................................... 10

8 Protection against accidental contact with live parts ....................................................... 12

9 Terminals ....................................................................................................................... 12

10 Provisions for protective earthing ................................................................................... 12

11 Moisture resistance and insulation .................................................................................. 12

12 Electric strength ............................................................................................................. 12

13 Thermal endurance test for windings of ballasts ............................................................. 12

14 Fault conditions .............................................................................................................. 12

15 Starting conditions .......................................................................................................... 12

16 Lamp current .................................................................................................................. 13

17 Supply current ................................................................................................................ 13

18 Maximum current in any lead (with cathode preheating) ................................................. 13

19 Lamp operating current waveforms ................................................................................. 13

20 Functional safety (EBLF) ................................................................................................ 14

21 Changeover operation .................................................................................................... 15

22 Recharging device .......................................................................................................... 16

23 Protection against excessive discharge .......................................................................... 18

24 Indicator ......................................................................................................................... 19

25 Remote control, rest mode, inhibition mode .................................................................... 19

26 Temperature cycling test and endurance test ................................................................. 20

27 Polarity reversal ............................................................................................................. 20

28 Fault conditions .............................................................................................................. 21

29 Construction ................................................................................................................... 21

30 Creepage distances and clearances ............................................................................... 21

31 Screws, current-carrying parts and connections .............................................................. 21

32 Resistance to heat, fire and tracking ............................................................................... 21

33 Resistance to corrosion .................................................................................................. 21

34 Abnormal lamp conditions .............................................................................................. 21

35 Protection of associated components ............................................................................. 26

Annex A (normative) Test to establish whether a conductive part is a live part, which

may cause an electric shock ................................................................................................. 28

Annex B (normative) Particular requirements for thermally protected lamp controlgear ........ 28

Annex C (normative) Particular requirements for electronic lamp controlgear with

means of protection against overheating ............................................................................... 28

---------------------- Page: 8 ----------------------
SIST EN 61347-2-7:2012
61347-2-7 © IEC:2011 – 3 –

Annex D (normative) Requirements for carrying out the heating test of thermally

protected lamp controlgear ................................................................................................... 28

Annex E (normative) Use of constant S other than 4 500 in t tests ..................................... 28

Annex F (normative) Draught-proof enclosure ...................................................................... 28

Annex G (normative) Explanation of the derivation of the values of pulse voltages .............. 29

Annex H (normative) Tests .................................................................................................. 29

Annex I (normative) Batteries for emergency lighting luminaires .......................................... 29

Annex J (informative) Rest mode and inhibition mode facilities ............................................ 29

Annex K (normative) Ballasts incorporating an automatic testing function for

emergency lighting operation ................................................................................................ 30

Annex L (informative) Compatibility between normal mains operation electronic

controlgear and battery-powered emergency operation controlgear ..................................... 33

Figure 1 – Suitable circuit for the measurement of lamp current and luminous flux ............... 15

Figure 2 – Rectifying effect test ............................................................................................ 23

Figure 3 – Circuit to test whether a controlgear can withstand a leaking burner .................... 24

Figure 4 – Circuit to test whether a ballast can withstand rectification ................................... 26

Figure L.1 – Timing diagram: changeover operation .............................................................. 34

Figure L.2 – Supply voltage for the function test ................................................................... 35

Table 1 – Voltage per cell to which the battery is discharged ................................................ 16

Table 2 – Relation between r.m.s. working voltage and maximum peak voltage .................... 26

Table K.1 – Relevant requirements of IEC 62034 .................................................................. 30

---------------------- Page: 9 ----------------------
SIST EN 61347-2-7:2012
– 4 – 61347-2-7 © IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LAMP CONTROLGEAR –
Part 2-7: Particular requirements for battery supplied electronic
controlgear for emergency lighting (self-contained)
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 61347-2-7 has been prepared by subcommittee 34C: Auxiliaries

for lamps, of IEC technical committee 34: Lamps and related equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
34C/995/FDIS 34C/1002/RVD

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.

This third edition cancels and replaces the second edition published in 2006. It constitutes a

technical revision. Significant changes introduced into this third edition include:

---------------------- Page: 10 ----------------------
SIST EN 61347-2-7:2012
61347-2-7 © IEC:2011 – 5 –

• modification of IEC 61347-2-7 to become a standard exclusively for d.c. battery

supplied electronic controlgear for emergency lighting (self-contained).

IEC 61347-2-3 Annex J is intended to cover centrally supplied emergency controlgear;

• update of Clause 22 – Recharging devices;
• modification of Clause 20 battery voltage characterisation to support EBLF
measurement. This to simplify and increase reproducibility of testing;
• rationalisation of requirements between IEC 61347-2-7 and IEC 60598-2-22
requirements of IEC 60598-2-22 being transferred to IEC 61347-2-7.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

This standard shall be used in conjunction with IEC 61347-1. This part 2 supplements or

modifies the corresponding clauses in IEC 61347-1.
NOTE In this standard, the following print types are used:
− requirements: in roman type;
− test specifications: in italic type;
− notes: in small roman type.

A list of all parts of the IEC 61347 series, published under the general title Lamp controlgear,

can be found on the IEC website.

The committee has decided that the contents of this publication will remain unchanged until

the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data

related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates

that it contains colours which are considered to be useful for the correct

understanding of its contents. Users should therefore print this document using a

colour printer.
---------------------- Page: 11 ----------------------
SIST EN 61347-2-7:2012
– 6 – 61347-2-7 © IEC:2011
INTRODUCTION

The formatting into separately published parts provides for ease of future amendments and

revisions. Additional requirements will be added as and when a need for them is recognized.

This standard, and the parts which make up IEC 61347-2, in referring to any of the clauses of

IEC 61347-1, specify the extent to which such a clause is applicable and the order in which

the tests are to be performed; they also include additional requirements, as necessary. All

parts which make up IEC 61347-2 are self-contained and, therefore, do not include reference

to each other.

Where the requirements of any of the clauses of IEC 61347-1 are referred to in this standard

by the phrase “The requirements of Clause n of IEC 61347-1 apply", this phrase is interpreted

as meaning that all requirements of the clause in question of Part 1 apply, except any which

are clearly inapplicable to the specific type of lamp controlgear covered by this particular part

of IEC 61347-2.
---------------------- Page: 12 ----------------------
SIST EN 61347-2-7:2012
61347-2-7 © IEC:2011 – 7 –
LAMP CONTROLGEAR –
Part 2-7: Particular requirements for battery supplied electronic
controlgear for emergency lighting (self-contained)
1 Scope

This part of IEC 61347 specifies particular safety requirements for battery supplied electronic

controlgear for maintained and non-maintained emergency lighting purposes.

It includes specific requirements for electronic controlgear and control units for self-contained

luminaires for emergency lighting as specified by IEC 60598-2-22.

It is intended for controlgear for fluorescent lamps, but it is also applicable to other lamp types

e.g. incandescent, high pressure discharge lamps and LEDs.

This standard covers the emergency mode operation of a controlgear. For controlgear with a

combination of normal and emergency lighting operation, the normal lighting operation

aspects are covered by the appropriate part 2 of IEC 61347.

DC supplied electronic controlgear for emergency lighting may or may not include batteries.

This standard also includes operational requirements for electronic controlgear, which, in the

case of d.c. supplied electronic controlgear, are regarded as performance requirements. This

is because non-operational emergency lighting equipment presents a safety hazard. It does

not apply to d.c. supplied electronic controlgear for emergency lighting, which are intended for

connection to a centralised emergency power supply system. A centralised emergency power

system could be a central battery system.

NOTE Annex J of IEC 61347-2-3 applies to a.c., a.c./d.c. or d.c. supplied electronic controlgear for connection to

centralised emergency power supply systems that are also intended for emergency lighting operations from

a.c./d.c. supplies.
2 Normative references

For the purpose of this part of IEC 61347, the normative references given in Clause 2 of

IEC 61347-1, which are mentioned in this standard, apply, together with the following

normative references.
IEC 60081, Double-capped fluorescent lamps – Performance specifications

IEC 60598-2-22, Luminaires – Part 2: Particular requirements – Luminaires for emergency

lighting
IEC 60901, Single-capped fluorescent lamps – Performance specifications
IEC 60921, Ballasts for tubular fluorescent lamps – Performance requirements

IEC 60929, AC and/or DC-supplied electronic control gear for tubular fluorescent lamps –

Performance requirements
IEC 61347-1, Lamp controlgear – Part 1: General and safety requirements
---------------------- Page: 13 ----------------------
SIST EN 61347-2-7:2012
– 8 – 61347-2-7 © IEC:2011

IEC 61347-2-3, Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c.

supplied electronic control gear for fluorescent lamps

IEC 61558-1:2005, Safety of power transformers, power supplies, reactors and similar

products – Part 1: General requirements and tests
Amendment 1 (2009)

IEC 61558-2-1:2007, Safety of power transformers, power supply units and similar products–

Part 2-1: Particular requirements and tests for separating transformers and power supplies

incorporating separating transformers for general applications

IEC 61558-2-6:2009, Safety of transformers, reactors, power supply units and similar products

for supply voltages up to 1 100 V – Part 2-6: Particular requirements and tests for safety

isolating transformers and power supply units incorporating safety isolating transformers

IEC 61558-2-16:2009, Safety of transformers, reactors, power supply units and similar

products for supply voltages up to 1 100 V – Part 2-16: Particular requirements and tests for

switch mode power supply units and transformers for switch mode power supply units

IEC 62034, Automatic test systems for battery powered emergency escape lighting
3 Terms and definitions

For the purposes of this part of IEC 61347, the terms and definitions of Clause 3 of

IEC 61347-1 and Clause 22.3 in IEC 60598-2-22 apply, together with the following:

3.1
emergency lighting
lighting provided for use when the supply to the normal lighting fails
3.2
changeover operation

automatic connection of the lamp to emergency lighting supply when failure of the normal

lighting supply occurs, and connecting automatically back to the normal lighting supply when

it is restored
3.3
recharging device

device to maintain the battery charge and to recharge the battery within a specified time

3.4
protection device against extensive discharge

automatic device to disconnect the ballast from the battery when the battery voltage drops

below a certain value
3.5
rated duration of emergency operation

time, as claimed by the manufacturer, for which the rated emergency ballast lumen factor is

achieved
3.6
maximum d.c. operating voltage
maximum supply voltage declared by the controlgear manufacturer
—————————

There exists a consolidated edition 2.1 (2009) comprising IEC 61558-1 (2005) and its Amendment 1 (2009).

---------------------- Page: 14 ----------------------
SIST EN 61347-2-7:2012
61347-2-7 © IEC:2011 – 9 –

For battery supplied controlgear, this is the maximum battery voltage available in the fully

charged condition.
3.7
rated d.c. operating voltage
nominal supply voltage declared by the controlgear manufacturer

For battery supplied controlgear, this is the nominal battery voltage declared by the battery

manufacturer.
3.8
d.c. voltage range
voltage range between minimum and maximum rated d.c. operating voltages
3.9
rated a.c. operating voltage

nominal supply voltage declared by the controlgear manufacturer for battery charger or

maintained controlgear operation
3.10
a.c. voltage range
voltage range between minimum and maximum rated a.c.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.