SIST EN 60317-69:2017

Specifications for particular types of winding wires - Part 69: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular aluminium wire, class 220 (IEC 60317-69:2017)

IEC 60317-69:2017(E) specifies the requirements of enamelled rectangular aluminium winding wire of class 220 with a dual coating. The underlying coating is based on polyester or polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide-imide resin. The range of nominal conductor dimensions covered by this standard is:

   
      
         
         
         
      
      
         
         
         
      
      
         
         
         
      
   

	Minimum	Maximum
Width	2,0 mm	16,0 mm
Thickness	0,80 mm	5,60 mm

    

Wires of grade 1 and grade 2 are included in this part of IEC 60317 and apply to the complete range of conductors. The specified combinations of width and thickness as well as the specific ratio width/thickness are given in IEC 60317.
This publication is to be read in conjunction with IEC 60317-0-9:2015
Keywords: insulated wires used for windings in electrical equipment,  class 220

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 69: Mit Polyester oder Polyesterimid beschichteter, mit Polyamidimid lackierter Flachdraht aus Aluminium der Klasse 220

Spécifications pour types particuliers de fils de bobinage - Partie 69: Fil d’aluminium de section rectangulaire émaillé avec polyester ou polyestérimide et avec surcouche polyamide-imide, classe 220

IEC 60317-69:2017 spécifie les exigences relatives au fil de bobinage d’aluminium de section rectangulaire émaillé de classe 220 avec un double revêtement. Le revêtement sous-jacent est à base de résine polyester ou polyestérimide, qui peut être modifiée à condition de conserver la dénomination chimique de la résine d'origine et satisfaire à toutes les exigences spécifiées du fil. Le revêtement superposé est à base de résine polyamide-imide. La plage de dimensions nominales du conducteur couverte par la présente norme est la suivante:

   
      
         
         
         
      
      
         
         
         
      
      
         
         
         
      
   

	Minimal	Maximal
Largeur	2,0 mm	16,0 mm
Epaisseur	0,80 mm	5,60 mm

Les fils de grade 1 et de grade 2 sont inclus dans la présente partie de l'IEC 60317 et s’appliquent à la plage complète de conducteurs. Les combinaisons spécifiées de largeurs et d’épaisseurs ainsi que le rapport spécifique largeur/épaisseur sont donnés dans IEC IEC 60317-0-9:2015.
Mots clés: fils isolés utilisés dans les enroulements des appareils électriques, classe 220

Specifikacije za posebne vrste navijalnih žic - 69. del: Aluminijasta žica s pravokotnim prerezom, emajlirana s poliamidimidom, prekrita s poliestrom ali poliesterimidom, razred 220 (IEC 60317-69:2017)

V ta del standarda IEC 60317 so vključene žice razreda 1 in 2 ter se uporabljajo za celoten nabor prevodnikov.
Navedene kombinacije širine in debeline ter določena razmerja med širino in debelino so podani v standardu IEC 60317-0-9.

General Information

• Status: Published
• Publication Date: 14-May-2017
• ICS: 29.060.10 - Wires
• ICS: 77.150.10 - Aluminium products
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 26-Apr-2017
• Due Date: 01-Jul-2017
• Completion Date: 15-May-2017
• Ref Project: EN 60317-69:2017 - Specifications for particular types of winding wires - Part 69: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular aluminium wire, class 220

Relations

• Amended By: SIST EN 60317-69:2017/A1:2024 - Specifications for particular types of winding wires - Part 69: Polyester or polyesterimide overcoated with polyamide-imide enamelled rectangular aluminium wire, class 220 (IEC 60317-69:2017/AMD1:2024)
• Effective Date: 01-Sep-2024

Overview

SIST EN 60317-69:2017 is a European standard that specifies the requirements for a particular type of winding wire used in electrical equipment. It details specifications for polyester or polyesterimide enamelled rectangular aluminium wire that is overcoated with a polyamide-imide layer, classified as thermal class 220. This dual-coated aluminium wire supports advanced insulation and thermal endurance, making it suitable for demanding electrical applications.

The standard is harmonized with the international IEC 60317-69:2017 and forms part of a larger body of standards related to winding wires. It ensures uniformity in material properties, dimensions, and performance, providing critical guidelines for manufacturers and users of insulated aluminium wires. The scope covers conductor dimensions from 2.0 mm to 16.0 mm in width and 0.8 mm to 5.6 mm in thickness, addressing both grade 1 and grade 2 wires.

Key Topics

• Dual Coating Composition: The wire features an underlying coating of polyester or polyesterimide resin, which can be chemically modified to enhance performance while retaining its base properties. A top coating of polyamide-imide resin is applied to improve insulation and heat resistance.
• Thermal Class 220: The wire meets the class 220 requirements, including a minimum temperature index of 220°C and heat shock resistance of at least 240°C, essential for high-temperature electrical environments.
• Dimensional Specifications: Standardized conductor dimensions ensure consistent electrical resistance and mechanical properties. Width ranges from 2 mm to 16 mm, thickness from 0.8 mm to 5.6 mm.
• Performance Tests: The standard references test methods related to electrical resistance, elongation, flexibility, heat shock, solvent resistance, breakdown voltage, and temperature index following IEC 60317-0-9:2015 and IEC 60851-4:2016.
• Exclusions: Certain tests such as cut-through resistance, abrasion resistance, and continuity of insulation are marked as not applicable for this particular wire type.
• Compliance and Certification: EN 60317-69 aligns with IEC requirements and is intended for adoption by national electrotechnical committees, ensuring compatibility across European and international markets.

Applications

EN 60317-69 certified rectangular aluminium winding wires with polyester or polyesterimide and polyamide-imide coatings are used predominantly in the manufacture of electrical equipment requiring reliable insulated conductors. Practical applications include:

• Electrical Motors and Generators: Ensuring high thermal stability and electrical insulation under operational stress.
• Transformers and Inductors: Benefiting from precise conductor dimensions and reliable insulation for efficient electromagnetic performance.
• Power Electronics: High-class insulation supports components operating at elevated temperatures and in harsh conditions.
• Automotive and Industrial Wiring: Durable insulation layers and thermal ratings make these wires suitable for demanding environments.
• Specialized Electrical Equipment: Applications requiring lightweight aluminium conductors with superior heat and chemical resistance.

This standard facilitates product development, quality control, and regulatory compliance for manufacturers and designers in the electrical and electronics sectors.

Related Standards

SIST EN 60317-69:2017 should be used in conjunction with the following standards to ensure comprehensive understanding and compliance:

• IEC 60317-0-9:2015 – General requirements for enamelled rectangular aluminium wires, including dimensional and electrical properties.
• IEC 60851-4:2016 – Chemical test methods for winding wires, crucial for verifying coating composition and resistance.
• IEC 60264 Series – Packaging standards for winding wires, ensuring proper handling and transportation.
• Other parts of the IEC 60317 Series – Covering specifications for different types of winding wires.
• National and regional adoptions of these standards via CENELEC and other bodies ensure harmonized electrotechnical regulations across markets.

---

Keywords: EN 60317-69, IEC 60317-69, polyesterimide, polyamide-imide, enamelled rectangular aluminium wire, class 220, winding wires, electrical insulation, thermal class 220, aluminium conductor, electrical equipment, coated winding wire standards, CENELEC standards, IEC winding wire specifications.

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2017
Specifikacije za posebne vrste navijalnih žic - 69. del: Aluminijasta žica s
pravokotnim prerezom, emajlirana s poliamidimidom, prekrita s poliestrom ali
poliesterimidom, razred 220 (IEC 60317-69:2017)
Specifications for particular types of winding wires - Part 69: Polyester or polyesterimide
overcoated with polyamide-imide enamelled rectangular aluminium wire, class 220 (IEC
60317-69:2017)
Ta slovenski standard je istoveten z: EN 60317-69:2017
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60317-69

NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2017
ICS 29.060.10
English Version
Specifications for particular types of winding wires -
Part 69: Polyester or polyesterimide overcoated with polyamide-
imide enamelled rectangular aluminium wire, class 220
(IEC 60317-69:2017)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 69: Fil d'aluminium de section rectangulaire émaillé Wickeldrähten - Teil 69: Mit Polyester oder Polyesterimid
de polyester ou polyestérimide et avec surcouche beschichteter, mit Polyamidimid lackierter Flachdraht aus
polyamide-imide, classe 220 Aluminium der Klasse 220
(IEC 60317-69:2017) (IEC 60317-69:2017)
This European Standard was approved by CENELEC on 2017-02-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-69:2017 E
European foreword
The text of document 55/1571/CDV, future edition 1 of IEC 60317-69, prepared by
IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60317-69:2017.
The following dates are fixed:
(dop) 2017-11-24
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-02-24
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60317-69:2017 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60264 Series NOTE Harmonized as EN 60264 Series.
IEC 60317 Series NOTE Harmonized as EN 60317 Series.
IEC 60851 Series NOTE Harmonized as EN 60851 Series.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
Publication Year Title EN/HD Year

IEC 60317-0-9 2015 Specifications for particular types EN 60317-0-9 2015
of winding wires -
Part 0-9: General requirements -
Enamelled rectangular aluminium wire
IEC 60851-4 2016 Winding wires - Test methods - EN 60851-4 2016
Part 4: Chemical properties
IEC 60317-69 ®
Edition 1.0 2017-01
INTERNATIONAL
STANDARD
Specifications for particular types of winding wires –

Part 69: Polyester or polyesterimide overcoated with polyamide-imide enamelled

rectangular aluminium wire, class 220

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.060.10 ISBN 978-2-8322-3842-4

– 2 – IEC 60317-69:2017 © IEC 2017
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 7
11 Resistance to abrasion . 7
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil . 8
21 Loss of mass . 8
23 Pin hole test . 8
30 Packaging .
...