Electrostatics - Part 5-3: Protection of electronic devices from electrostatic phenomena - Properties and requirements classification for packaging intended for electrostatic discharge sensitive devices

This part of IEC 61340 defines the ESD protective packaging properties needed to protect
electrostatic discharge sensitive devices (ESDS) through all phases of production,
rework/maintenance, transport and storage. Test methods are referenced to evaluate
packaging and packaging materials for these product and material properties. Performance
limits are provided.
This standard does not address protection from electromagnetic interference (EMI),
electromagnetic pulsing (EMP) or protection of volatile materials.

Elektrostatik - Teil 5-3: Schutz von elektronischen Bauelementen gegen elektrostatische Phänomene - Eigenschaften und Anforderungen für die Klassifizierung von Verpackungen, welche für Bauelemente verwendet werden, die gegen elektrostatische Entladungen empfindlich sind

Électrostatique - Partie 5-3: Protection des dispositifs électroniques contre les phénomènes électrostatiques - Classification des propriétés et des exigences relatives à l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques

IEC 61340-5-3:2015 définit les propriétés des emballages de protection contre les ESD nécessaires pour protéger les dispositifs sensibles aux décharges électrostatiques (ESDS) pendant toutes les phases de production, réusinage/maintenance, de transport et de stockage. Les méthodes d'essai sont référencées pour évaluer les emballages et les matériaux d'emballages concernant les propriétés de ces produits et matériaux. Des limites de performance sont données. La présente norme ne traite pas de la protection contre le brouillage électromagnétique (EMI, Electromagnetic Interference), le brouillage radioélectrique (RFI, Radio Frequency Interference), les impulsions électromagnétiques (IEM) ni de la protection des matériaux volatils. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) suppression de toutes les références à l'ANSI/ESD STM11.13, remplacée par la référence normative IEC 61340-4-10;
b) notes supplémentaires ajoutées dans le Tableau 1;
c) ajout d'un Tableau supplémentaire 3 lié au "symbole de classification ESD" et au "code de fonction primaire".

Elektrostatika - 5-3. del: Zaščita elektronskih naprav pred elektrostatičnimi pojavi - Lastnosti in klasifikacija zahtev za embalažo naprav, ki so občutljive za elektrostatične razelektritve

Ta del standarda IEC 61340 opredeljuje lastnosti, ki jih mora imeti embalaža za zaščito pred elektrostatično razelektritvijo, da zaščiti naprave, občutljive za elektrostatično razelektritev (ESD), v vseh fazah izdelave, popravila/vzdrževanja, prevoza in skladiščenja. Preskusne metode so navedene za ocenjevanje embalaže in materialov za embalažo teh izdelkov ter lastnosti materialov. Podane so omejitve delovanja. Ta standard ne obravnava zaščite pred elektromagnetnimi motnjami (EMI) in elektromagnetnimi sunki (EMP) ali zaščite vnetljivih materialov.

General Information

Status
Published
Publication Date
09-Nov-2015
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
14-Oct-2015
Due Date
19-Dec-2015
Completion Date
10-Nov-2015

Relations

Buy Standard

Standard
EN 61340-5-3:2015
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61340-5-3:2015
01-december-2015
1DGRPHãþD
SIST EN 61340-5-3:2010
(OHNWURVWDWLNDGHO=DãþLWDHOHNWURQVNLKQDSUDYSUHGHOHNWURVWDWLþQLPLSRMDYL
/DVWQRVWLLQNODVLILNDFLMD]DKWHY]DHPEDODåRQDSUDYNLVRREþXWOMLYH]D
HOHNWURVWDWLþQHUD]HOHNWULWYH
Electrostatics - Part 5-3: Protection of electronic devices from electrostatic phenomena -
Properties and requirements classification for packaging intended for electrostatic
discharge sensitive devices
Électrostatique - Partie 5-3: Protection des dispositifs électroniques contre les
phénomènes électrostatiques - Classification des propriétés et des exigences relatives à
l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques
Ta slovenski standard je istoveten z: EN 61340-5-3:2015
ICS:
17.220.99 Drugi standardi v zvezi z Other standards related to
elektriko in magnetizmom electricity and magnetism
SIST EN 61340-5-3:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61340-5-3:2015

---------------------- Page: 2 ----------------------

SIST EN 61340-5-3:2015


EUROPEAN STANDARD EN 61340-5-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2015
ICS 17.220.99; 29.020 Supersedes EN 61340-5-3:2010
English Version
Electrostatics - Part 5-3: Protection of electronic devices from
electrostatic phenomena - Properties and requirements
classification for packaging intended for electrostatic discharge
sensitive devices
(IEC 61340-5-3:2015)
Électrostatique - Partie 5-3: Protection des dispositifs Elektrostatik - Teil 5-3: Schutz von elektronischen
électroniques contre les phénomènes électrostatiques - Bauelementen gegen elektrostatische Phänomene -
Classification des propriétés et des exigences relatives à Eigenschaften und Anforderungen für die Klassifizierung
l'emballage destiné aux dispositifs sensibles aux décharges von Verpackungen, welche für Bauelemente verwendet
électrostatiques werden, die gegen elektrostatische Entladungen
(IEC 61340-5-3:2015) empfindlich sind
(IEC 61340-5-3:2015)
This European Standard was approved by CENELEC on 2015-08-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61340-5-3:2015 E

---------------------- Page: 3 ----------------------

SIST EN 61340-5-3:2015
EN 61340-5-3:2015
European foreword
The text of document 101/428/CDV, future edition 2 of IEC 61340-5-3, prepared by IEC/TC 101
"Electrostatics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 61340-5-3:2015.
The following dates are fixed:
(dop) 2016-05-20
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2018-08-20
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 61340-5-3:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61340-5-3:2015 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61340-5-1 NOTE Harmonized as EN 61340-5-1.
IEC 60749-26 NOTE Harmonized as EN 60749-26.
2

---------------------- Page: 4 ----------------------

SIST EN 61340-5-3:2015
EN 61340-5-3:2015
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60417 -  Graphical symbols for use on equipment - -
IEC 61340-2-3 -  Electrostatics - EN 61340-2-3 -
Part 2-3: Methods of test for determining
the resistance and resistivity of solid planar
materials used to avoid electrostatic charge
accumulation
IEC 61340-4-8 -  Electrostatics - EN 61340-4-8 -
Part 4-8: Standard test methods for specific
applications - Electrostatic discharge
shielding - Bags
IEC 61340-4-10 -  Electrostatics - - -
Part 4-10: Standard test methods for
specific applications - Two-point resistance
measurement

3

---------------------- Page: 5 ----------------------

SIST EN 61340-5-3:2015

---------------------- Page: 6 ----------------------

SIST EN 61340-5-3:2015



IEC 61340-5-3

®


Edition 2.0 2015-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Electrostatics –

Part 5-3: Protection of electronic devices from electrostatic phenomena –

Properties and requirements classification for packaging intended for


electrostatic discharge sensitive devices



Électrostatique –


Partie 5-3: Protection des dispositifs électroniques contre les phénomènes

électrostatiques – Classification des propriétés et des exigences relatives à

l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 17.220.99; 29.020 ISBN 978-2-8322-2787-9



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61340-5-3:2015
– 2 – IEC 61340-5-3:2015  IEC 2015
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and abbreviations . 7
3.1 Terms and definitions . 7
3.2 Abbreviations . 9
4 Tailoring . 9
5 Packaging application requirement . 9
5.1 General . 9
5.2 Inside an EPA . 9
5.3 Outside an EPA . 9
6 Classification of ESD packaging material properties . 10
6.1 General . 10
6.2 Material resistance properties . 10
6.2.1 General . 10
6.2.2 Resistance of conductive materials . 10
6.2.3 Resistance of electrostatic field shielding materials . 10
6.2.4 Resistance of dissipative materials . 11
6.2.5 Resistance of insulating materials. 11
6.3 Material electrostatic shielding properties . 11
6.3.1 Electrostatic discharge shielding . 11
6.3.2 Electrostatic field shielding . 11
7 Technical requirements for ESD protective packaging . 11
7.1 Packaging and material properties . 11
7.2 Packaging marking . 13
7.2.1 Classification symbol . 13
7.2.2 Packaging classification. 13
7.2.3 Traceability . 14
Annex A (informative) ESD packaging material guidance . 15
A.1 Environment and device sensitivity . 15
A.1.1 General . 15
A.1.2 Environment . 15
A.1.3 Device sensitivity . 16
A.2 Equipotential bonding . 17
A.3 Dissipative material for intimate contact . 17
A.4 Packaging from incoming material to the point of use . 17
A.5 Periodic verification . 18
A.6 Examples of measurement procedures for qualification and verification of
packaging . 19
Annex B (informative) Device damage . 20
B.1 Damage from ESD . 20
B.2 Discharge to a device . 20
B.2.1 Human body model (HBM) [2] and isolated conductors . 20
B.2.2 Retained charge . 20

---------------------- Page: 8 ----------------------

SIST EN 61340-5-3:2015
IEC 61340-5-3:2015  IEC 2015 – 3 –
B.3 Discharge from a device . 20
B.3.1 Charged device model (CDM) . 20
B.3.2 Tribo-electrification . 20
Bibliography . 21

Figure 1 – Example of packaging label (*Primary function code) . 13
Figure A.1 – Examples of EPA configurations . 16
Figure A.2 – Application of ESD protective packaging . 18

Table 1 – Test methods for electrostatic protective packaging . 12
Table 2 – Test methods and requirements for electrostatic discharge shielding
packaging . 12
Table 3 – Primary function code/ESD classification symbol . 14
Table A.1 – Packaging characteristics for environmental consideration . 15
Table A.2 – Examples for qualification and verification of packaging . 19

---------------------- Page: 9 ----------------------

SIST EN 61340-5-3:2015
– 4 – IEC 61340-5-3:2015  IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTROSTATICS –

Part 5-3: Protection of electronic devices from electrostatic phenomena –
Properties and requirements classification for packaging intended for
electrostatic discharge sensitive devices

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61340-5-3 has been prepared by IEC technical committee 101:
Electrostatics.
This second edition cancels and replaces the first edition published in 2010. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) removal of all references to ANSI/ESD STM11.13, replaced by normative reference
IEC 61340-4-10;
b) additional notes added to Table 1;
c) addition of a new Table 3 related to the “ESD classification symbol” and the “primary
function code”.

---------------------- Page: 10 ----------------------

SIST EN 61340-5-3:2015
IEC 61340-5-3:2015  IEC 2015 – 5 –
The text of this standard is based on the following documents:
CDV Report on voting
101/428/CDV 101/457/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 61340 series, under the general title Electrostatics, can be found
on the IEC website
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------

SIST EN 61340-5-3:2015
– 6 – IEC 61340-5-3:2015  IEC 2015
INTRODUCTION
Packaging is necessary to protect electrostatic discharge sensitive devices (ESDS) from
physical and environmental damage during manufacture, transportation and storage.
Additionally, packaging for ESDS should also prevent damage from static electricity.

---------------------- Page: 12 ----------------------

SIST EN 61340-5-3:2015
IEC 61340-5-3:2015  IEC 2015 – 7 –
ELECTROSTATICS –

Part 5-3: Protection of electronic devices from electrostatic phenomena –
Properties and requirements classification for packaging intended for
electrostatic discharge sensitive devices



1 Scope
This part of IEC 61340 defines the ESD protective packaging properties needed to protect
electrostatic discharge sensitive devices (ESDS) through all phases of production,
rework/maintenance, transport and storage. Test methods are referenced to evaluate
packaging and packaging materials for these product and material properties. Performance
limits are provided.
This standard does not address protection from electromagnetic interference (EMI),
electromagnetic pulsing (EMP) or protection of volatile materials.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61340-2-3, Electrostatics – Part 2-3: Methods of test for determining the resistance and
resistivity of solid planar materials used to avoid electrostatic charge accumulation
IEC 61340-4-8, Electrostatics – Part 4-8: Standard test methods for specific applications –
Electrostatic discharge shielding − Bags
IEC 61340-4-10, Electrostatics – Part 4-10: Standard test methods for specific applications –
Two-point resistance measurement1
IEC 60417, Graphical symbols for use on equ
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.