SIST EN ISO 15527:2019
(Main)Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2018)
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2018)
This document specifies the requirements and test methods for solid flat compression-moulded sheets
of polyethylene (PE-UHMW and PE-HD, see ISO 1043-1) without fillers or reinforcing materials. It
applies only to thicknesses from 10 mm to 200 mm.
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen und Prüfverfahren (ISO 15527:2018)
Dieses Dokument legt die Anforderungen und Prüfverfahren an massive ebene gepresste Tafeln aus Polyethylen (PE UHMW und PE HD, siehe ISO 1043 1) ohne Füll- oder Verstärkungsstoffe fest. Sie gilt nur für Tafeldicken von 10 mm bis 200 mm.
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) - Exigences et méthodes d'essai (ISO 15527:2018)
Le présent document spécifie les exigences et les méthodes d'essai pour les plaques moulées par compression, compactes et planes, en polyéthylène (PE-UHMW et PE-HD, voir l'ISO 1043-1) sans charges ou matériaux de renforcement. Il s'applique uniquement aux plaques de 10 mm à 200 mm d'épaisseur.
Polimerni materiali - Kompresijsko brizgane polietilenske plošče (PE-UHMW, PE-HD) - Zahteve in preskusne metode (ISO 15527:2018)
Ta dokument določa zahteve in preskusne metode za masivne ravne kompresijsko brizgane polietilenske plošče (PE-UHMW in PE-HD, glej standard ISO 1043-1) brez polnil ali materialov za ojačanje. Uporablja se le za debeline od 10 mm do 200 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15527:2019
01-februar-2019
1DGRPHãþD
SIST EN ISO 15527:2013
3ROLPHUQLPDWHULDOL.RPSUHVLMVNREUL]JDQHSROLHWLOHQVNHSORãþH 3(8+0:3(
+' =DKWHYHLQSUHVNXVQHPHWRGH ,62
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -
Requirements and test methods (ISO 15527:2018)
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen
und Prüfverfahren (ISO 15527:2018)
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) -
Exigences et méthodes d'essai (ISO 15527:2018)
Ta slovenski standard je istoveten z: EN ISO 15527:2018
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 15527:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15527:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 15527:2019
EN ISO 15527
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 15527:2013
English Version
Plastics - Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) - Requirements and test methods (ISO
15527:2018)
Plastiques - Plaques moulées par compression en Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-
polyéthylène (PE-UHMW, PE-HD) - Exigences et UHMW, PE-HD) - Anforderungen und Prüfverfahren
méthodes d'essai (ISO 15527:2018) (ISO 15527:2018)
This European Standard was approved by CEN on 4 November 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15527:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15527:2019
EN ISO 15527:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15527:2019
EN ISO 15527:2018 (E)
European foreword
This document (EN ISO 15527:2018) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15527:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 15527:2018 has been approved by CEN as EN ISO 15527:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15527:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 15527:2019
INTERNATIONAL ISO
STANDARD 15527
Third edition
2018-11
Plastics — Compression-moulded
sheets of polyethylene (PE-UHMW, PE-
HD) — Requirements and test methods
Plastiques — Plaques moulées par compression en polyéthylène (PE-
UHMW, PE-HD) — Exigences et méthodes d'essai
Reference number
ISO 15527:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 15527:2019
ISO 15527:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15527:2019
ISO 15527:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material . 1
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . 2
5.2.3 Rectangularity . 2
5.3 Properties . 3
5.3.1 Physical properties . 3
5.3.2 Physiological behaviour . . 3
6 Test methods . 3
6.1 Test specimens . 3
6.1.1 Preparation of test specimens . 3
6.1.2 Conditioning . 4
6.1.3 Testing . 5
6.2 Delivery condition . 5
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness, h .5
6.4.2 Length, l, and width, b .5
6.4.3 Rectangularity . 5
6.5 Density . 5
6.6 Determination of abrasion properties . 5
6.7 Tensile stress at yield, σ , and tensile strain at yield, ε .
y y 5
6.8 Modulus of elasticity in tension, E .
t 5
6.9 Impact strength of notched specimens . 6
6.9.1 Charpy impact strength of double-notched specimens . 6
6.9.2 Charpy impact strength of single-notched specimens, a .
cN 6
6.10 Melt mass-flow rate (MFR) . 6
7 Designation . 6
8 Marking . 6
Annex A (normative) Requirements for rectangularity . 7
Annex B (normative) Determination of abrasion properties . 8
Annex C (informative) Example of apparatus for the determination of abrasion properties .10
Bibliography .11
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 15527:2019
ISO 15527:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introducti
...
SLOVENSKI STANDARD
oSIST prEN ISO 15527:2018
01-september-2018
3ROLPHUQLPDWHULDOL.RPSUHVLMVNREUL]JDQHSROLHWLOHQVNHSORãþH 3(8+0:3(
+' =DKWHYHLQSUHVNXVQHPHWRGH ,62)',6
Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) -
Requirements and test methods (ISO/FDIS 15527:2018)
Kunststoffe - Gepresste Tafeln aus Polyethylen (PE-UHMW, PE-HD) - Anforderungen
und Prüfverfahren (ISO/FDIS 15527:2018)
Plastiques - Plaques moulées par compression en polyéthylène (PE-UHMW, PE-HD) -
Exigences et méthodes d'essai (ISO/FDIS 15527:2018)
Ta slovenski standard je istoveten z: prEN ISO 15527
ICS:
83.140.10 Filmi in folije Films and sheets
oSIST prEN ISO 15527:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 15527:2018
---------------------- Page: 2 ----------------------
oSIST prEN ISO 15527:2018
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 15527
ISO/TC 61/SC 11
Plastics — Compression-moulded
Secretariat: JISC
sheets of polyethylene (PE-UHMW, PE-
Voting begins on:
20180710 HD) — Requirements and test methods
Voting terminates on:
Plastiques — Plaques moulées par compression en polyéthylène (PE-
20181002
UHMW, PE-HD) — Exigences et méthodes d'essai
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 15527:2018(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2018
---------------------- Page: 3 ----------------------
oSIST prEN ISO 15527:2018
ISO/FDIS 15527:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 15527:2018
ISO/FDIS 15527:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material . 1
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . 2
5.2.3 Rectangularity . 2
5.3 Properties . 3
5.3.1 Physical properties . 3
5.3.2 Physiological behaviour . . 3
6 Test methods . 3
6.1 Test specimens . 3
6.1.1 Preparation of test specimens . 3
6.1.2 Conditioning . 4
6.1.3 Testing . 5
6.2 Delivery condition . 5
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness, h .5
6.4.2 Length, l, and width, b .5
6.4.3 Rectangularity . 5
6.5 Density . 5
6.6 Determination of abrasion properties . 5
6.7 Tensile stress at yield, σ , and tensile strain at yield, ε .
y y 5
6.8 Modulus of elasticity in tension, E .
t 5
6.9 Impact strength of notched specimens . 6
6.9.1 Charpy impact strength of double-notched specimens . 6
6.9.2 Charpy impact strength of single-notched specimens, a .
cN 6
6.10 Melt mass-flow rate (MFR) . 6
7 Designation . 6
8 Marking . 6
Annex A (normative) Requirements for rectangularity . 7
Annex B (normative) Determination of abrasion properties . 8
Annex C (informative) Example of apparatus for the determination of abrasion properties .10
Bibliography .11
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 15527:2018
ISO/FDIS 15527:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This third edition cancels and replaces the second edition (ISO 15527:2010), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
— Clause 2 has been revised (in 6.9.2, ISO 1791, rather than ISO 115422, is now used to determine the
Charpy impact strength);
— the requirements given in Table 2 for the abrasion properties have been modified;
— Clause 3, Terms and definitions, has been added and the succeding clauses have been renumbered;
— the document has been editorially revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 15527:2018
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 15527:2018(E)
Plastics — Compression-moulded sheets of polyethylene
(PE-UHMW, PE-HD) — Requirements and test methods
1 Scope
This document specifies the requirements and test methods
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.