SIST EN ISO 10156-2:2005
(Main)Gas cylinders - Gases and gas mixtures - Part 2: Determination of oxidizing ability of toxic and corrosive gases and gas mixtures (ISO 10156-2:2005)
Gas cylinders - Gases and gas mixtures - Part 2: Determination of oxidizing ability of toxic and corrosive gases and gas mixtures (ISO 10156-2:2005)
20060524 - Withdrawal of EN 720-2:1996 cancelled by EN ISO 10156-2:2005/AC:2006
Gasflaschen - Gase und Gasgemische - Teil 2: Bestimmung des Oxidationsvermögens von giftigen und korrosiven Gasen und Gasgemischen (ISO 10156-2:2005)
Dieser Teil von ISO 10156 beinhaltet ein Prüf- und Berechnungsverfahren zur Bestimmung darüber, ob ein Gas oder Gasgemisch ein höheres Oxidationsvermögen als Luft hat. Diese Norm gilt nur für toxische und korrosive Gase und Gasgemische.
Bouteilles a gaz - Gaz et mélanges de gaz - Partie 2: Détermination du pouvoir oxydant des gaz et mélanges de gaz toxiques et corrosifs (ISO 10156-2:2005)
Plinske jeklenke – Plini in plinske mešanice – 2. del: Določitev stopnje oksidativnosti strupenih in korozivnih plinov in plinskih mešanic (ISO 10156-2:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10156-2:2005
01-november-2005
1DGRPHãþD
SIST EN 720-2:1999
3OLQVNHMHNOHQNH±3OLQLLQSOLQVNHPHãDQLFH±GHO 'RORþLWHYVWRSQMH
RNVLGDWLYQRVWLVWUXSHQLKLQNRUR]LYQLKSOLQRYLQSOLQVNLKPHãDQLF ,62
Gas cylinders - Gases and gas mixtures - Part 2: Determination of oxidizing ability of
toxic and corrosive gases and gas mixtures (ISO 10156-2:2005)
Gasflaschen - Gase und Gasgemische - Teil 2: Bestimmung des Oxidationsvermögens
von giftigen und korrosiven Gasen und Gasgemischen (ISO 10156-2:2005)
Bouteilles a gaz - Gaz et mélanges de gaz - Partie 2: Détermination du pouvoir oxydant
des gaz et mélanges de gaz toxiques et corrosifs (ISO 10156-2:2005)
Ta slovenski standard je istoveten z: EN ISO 10156-2:2005
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
71.100.20 Industrijski plini Gases for industrial
application
SIST EN ISO 10156-2:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10156-2:2005
---------------------- Page: 2 ----------------------
SIST EN ISO 10156-2:2005
EUROPEAN STANDARD
EN ISO 10156-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2005
ICS 23.020.30; 71.100.20 Supersedes EN 720-2:1996
English Version
Gas cylinders - Gases and gas mixtures - Part 2: Determination
of oxidizing ability of toxic and corrosive gases and gas mixtures
(ISO 10156-2:2005)
Bouteilles à gaz - Gaz et mélanges de gaz - Partie 2: Gasflaschen - Gase und Gasgemische - Teil 2:
Détermination du pouvoir oxydant des gaz et mélanges de Bestimmung des Oxidationsverhaltens von giftigen und
gaz toxiques et corrosifs (ISO 10156-2:2005) korrosiven Gasen und Gasgemischen (ISO 10156-2:2005)
This European Standard was approved by CEN on 31 July 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10156-2:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10156-2:2005
EN ISO 10156-2:2005 (E)
Foreword
This document (EN ISO 10156-2:2005) has been prepared by Technical Committee ISO/TC 58
"Gas cylinders" in collaboration with Technical Committee CEN/TC 23 "Transportable gas
cylinders", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by February 2006, and conflicting national
standards shall be withdrawn at the latest by February 2006.
This document supersedes EN 720-2:1996.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 10156-2:2005 has been approved by CEN as EN ISO 10156-2:2005 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10156-2:2005
INTERNATIONAL ISO
STANDARD 10156-2
First edition
2005-08-01
Gas cylinders — Gases and gas
mixtures —
Part 2:
Determination of oxidizing ability of toxic
and corrosive gases and gas mixtures
Bouteilles à gaz — Gaz et mélanges de gaz —
Partie 2: Détermination du pouvoir oxydant des gaz et mélanges de gaz
toxiques et corrosifs
Reference number
ISO 10156-2:2005(E)
©
ISO 2005
---------------------- Page: 5 ----------------------
SIST EN ISO 10156-2:2005
ISO 10156-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 10156-2:2005
ISO 10156-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10156-2 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2, Cylinder
fittings.
This first edition of ISO 10156-2, together with the future ISO 10156-1 (under preparation), will cancel and
replace ISO 10156:1996, which has been technically revised.
ISO 10156 consists of the following parts, under the general title Gas cylinders — Gases and gas mixtures:
Part 2: Determination of oxidizing ability of toxic and corrosive gases and gas mixtures
© ISO 2005 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 10156-2:2005
---------------------- Page: 8 ----------------------
SIST EN ISO 10156-2:2005
INTERNATIONAL STANDARD ISO 10156-2:2005(E)
Gas cylinders — Gases and gas mixtures —
Part 2:
Determination of oxidizing ability of toxic and corrosive gases
and gas mixtures
WARNING 1 — There may be a risk of explosion when carrying out the test specified in this part of
ISO 10156. Special care is to be taken when dealing with toxic and corrosive gases. Personnel shall be
made aware of the potential hazards and shall take the necessary precautions. The test apparatus
should be installed in a laboratory fume cupboard.
WARNING 2 — Fuel gas and oxidants to be tested shall not be mixed together under pressure in gas
cylinders, except by competent persons to a well proven procedure. This part of ISO 10156 does not
attempt to clarify which oxidizing gas mixtures can be manufactured safely and successfully; this is
the responsibility of the mixture manufacturer using established practices and procedures to ensu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.