oSIST prEN 15383:2005
Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers
Plastics piping systems for drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and inspection chambers
This standard specifies the requirements for GRP manholes, inspection chambers and ancillary fittings, with circular chamber and shaft sections, for use within a drain or sewer system under gravity or at low head of pressure, limited by non-pressure classification as defined in clause 3.
This European standard covers components to be used in systems for the conveyance of one or more of the following fluids:
- domestic wastewater
- surface water and
- other waste waters (e.g. trade effluent).
Products covered by this standard are either complete manholes, inspection chambers and ancillary fittings or individual units for the construction of manholes, inspection chambers or ancillary fittings.
It specifies definitions, material specification and properties, types, characteristics, requirements, test methods, marking.
Kunststoff Rohrleitungssysteme für Abwasserleitungen und -kanäle - Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von Polyesterharz (UP) - Einsteigschächte und Kontrollschächte
Diese Norm legt werden die Anforderungen an Einsteig und Kontrollschächte aus GFK UP mit kreisförmigen Querschnitten für Schächte und Steigrohre in Abwasserkanälen und leitungen mit Schwerkraftentwässerung oder mit geringem Druckgefälle fest, wobei für die Leitungen die in Abschnitt 3 definierte Klassifikation für drucklose Leitungen zutrifft.
Diese Europäische Norm erfasst Zubehörteile, die in Systemen zur Beförderung von einem oder mehreren der folgenden strömenden Medien angewendet werden:
- Haushaltsabwässer;
- Oberflächenwässer;
- sonstige Abwässer (z. B. Industrieabwässer).
Die in dieser Norm erfassten Produkte sind entweder die kompletten Einsteig und Kontrollschächte oder die einzelnen Baueinheiten, aus denen die Schächte entsprechend der vorgesehenen Anwendungen in erdverlegten Systemen zusammengesetzt werden.
Es werden Definitionen, Spezifikationen und Eigenschaften der Werkstoffe, Arten und Eigenschaften der Schächte, Anforderungen, Prüfverfahren und Kennzeichnung festgelegt.
ANMERKUNG Sofern sie die entsprechenden zusätzlichen Anforderungen nach den jeweils zutreffenden Europäischen Normen erfüllen, können die kompletten Einsteigschächte oder die vorgefertigten Baueinheiten auch für andere Zwecke angewendet werden, z. B. in Pumpstationen, Schächten zur Einbringung von Rohrleitungs Ausrüstungen, Absturzschächten, Absturzbauwerken, kombinierten Überläufen für Abwasser und Niederschlagswasser, als Teile von Entwässerungssystemen, Gehäuse für Einrichtungen zur Abwasserbehandlung, Teile für die Abwasserbehandlung oder entsorgung. Bei der Anwendung in Trinkwassersystemen gelten für die entsprechenden Bauteile die Anforderungen der zutreffenden Normen an Produkte, die mit Trinkwasser in Kontakt kommen.
Systemes de canalisations en plastiques pour les branchements et collecteurs d'assainissement - Plastiques thermodurcissables renforcés de verre (PRV) a base de résine de polyester (UP) - Regards et boîtes d'inspection et de branchement
Cevni sistemi iz polimernih materialov za odpadno vodo – S steklenimi vlakni okrepljeni duromerni materiali (GRP), ki temeljijo na nenasičeni poliestrski smoli (UP) – Vstopni in revizijski jaški
General Information
Standards Content (Sample)
SLOVENSKI oSIST prEN 15383:2005
PREDSTANDARD
december 2005
Cevni sistemi iz polimernih materialov za odpadno vodo – S steklenimi vlakni
okrepljeni duromerni materiali (GRP), ki temeljijo na nenasičeni poliestrski
smoli (UP) – Vstopni in revizijski jaški
Plastics piping systems for drainage and sewerage - Glass-reinforced
thermosetting plastics (GRP) based on polyester resin (UP) - Manholes and
inspection chambers
ICS 23.040.20; 91.140.80 Referenčna številka
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2005
ICS
English Version
Plastics piping systems for drainage and sewerage - Glass-
reinforced thermosetting plastics (GRP) based on polyester
resin (UP) - Manholes and inspection chambers
Systèmes de canalisations en plastiques pour les
branchements et collecteurs d'assainissement - Plastiques
thermodurcissables renforcés de verre (PRV) à base de
résine de polyester (UP) - Regards et boîtes d'inspection et
de branchement
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15383:2005: E
worldwide for CEN national Members.
Contents
Foreword. 4
Introduction . 4
1 Scope. 5
2 Normative references . 5
3 Terms and definitions. 6
3.1 Manholes and inspection chambers . 6
3.2 Prefabricated unit. 8
3.3 Components of the base unit.10
3.4 Component of the side entry manhole or inspection chamber . 11
3.5 Units forming the capping structure . 11
3.6 Slabs and other elements used as reducing unit. 12
3.7 Sizes and nominal values . 12
3.8 Performance. 13
3.9 Other . 14
4 Symbols . 15
5 Classification. 17
6 Place of installation . 17
7 Material specification and properties . 18
7.1 Chamber and shaft units. 18
7.2 Pipes, fittings and supporting material. 19
7.3 Benching and invert . 19
7.4 Slabs and adjusting unit. 20
7.5 Manhole top . 20
7.6 Joints. 20
7.7 Manhole steps and ladders. 20
8 Types of manholes and inspection chambers. 20
9 General characteristics . 26
9.1 National design and safety regulations. 26
9.2 General composition . 26
9.3 Serviceability and durability . 26
9.4 Design service temperature . 26
9.5 General appearance and finish. 26
9.6 Flexible connection . 27
9.7 Test conditions. 27
10 Geometrical characteristics. 27
10.1 General . 27
10.2 Vertical cylindrical components. 27
10.3 Geometry of cylindrical components. 30
10.4 Slabs . 30
10.5 Connections . 31
10.6 Benching and inverts in base units . 31
10.7 Manhole steps and ladders. 32
11 Mechanical characteristic requirements .32
12 Performance requirements .34
13 Conformity evaluation.36
13.1 General .36
13.2 Product evaluation procedures.36
14 Marking .36
Annex A (informative) Guidance for the assessment of conformity.38
A.1 GRP components .38
A.2 Non-GRP components.41
Annex B (normative) Test method for connections to sewer.42
B.1 Scope.42
B.2 Connection using an integrated pipe element .42
B.3 Connections using an integrated pipe coupling.42
Annex C (normative) Negative pressure test on units .44
C.1 Scope.44
C.2 Principle .44
C.3 Apparatus .44
C.4 Test pieces .44
C.5 Procedure .45
Annex D (informative) Test method for gas-tightness of inspection chambers and manholes 46
D.1 Scope.46
D.2 Principle .46
D.3 Apparatus .46
D.4 Test pieces .46
D.5 Procedure .47
Annex E (normative) Initial specific longitudinal compressive strength – Test method.48
E.1 Scope.48
E.2 Number of the test pieces.48
E.3 Dimension of the test pieces .48
E.4 Test.49
E.5 Test report .49
Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU
Construction Products Directive .50
ZA.1 Scope and relevant characteristics.50
ZA.2 Procedure(s) for the attestation of conformity of GRP manholes and inspection chambers. .51
ZA.3 CE marking and labeling.53
Bibliography.55
Foreword
This document (prEN 15383:2005) has been prepared by Technical Committee CEN/TC 155 "Plastics piping
systems and ducting systems", the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This European Standard is a System Standard for manholes and inspection chambers made of plastics piping
systems using glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP), for
drainage and sewerage. This European Standard has been prepared under a mandate given to CEN by the
European Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.
This European Standard includes three informative and three norma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.