SIST EN IEC 60317-60-1:2020

Specifications for particular types of winding wires - Part 60-1: Polyester glass-fibre wound fused, unvarnished, bare or enamelled rectangular copper wire, temperature index 155 (IEC 60317-60-1:2020)

IEC 60317-60-1: 2020 specifies the requirements of polyester glass-fibre wound fused, unvarnished, bare or grade 1 or grade 2 enamelled rectangular copper winding wires, temperature index 155.
NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requirements for temperature index and heat shock temperature cannot be specified.
The range of nominal conductor dimensions covered by this document is:
width: min. 2,0 mm max. 16,0 mm;
thickness: min. 0,80 mm max. 5,60 mm.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten – Teil 60-1:Flachdrähte aus Kupfer, mit Polyesterglasfasern umsponnen und verschmolzen, nicht lackiert, blank oder lackisoliert, Temperaturindex 155 (IEC 60317-60-1:2020)

Spécifications pour types particuliers de fils de bobinage - Partie 60-1: Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues non vernies, d'indice de température 155 (IEC 60317-60-1:2020)

IEC 60317-60-1:2020 spécifie les exigences relatives aux fils de bobinage de section rectangulaire en cuivre nus ou émaillés de grade 1 ou de grade 2, guipés de fibres de verre polyester fondues non vernies, d'indice de température 155.
NOTE Pour ce type de fil, l'essai de choc thermique ne s'applique pas et la température de choc thermique ne peut donc pas être définie. Par conséquent, il n'est pas possible de spécifier une classe fondée sur les exigences d'indice de température et de température de choc thermique.
La gamme des dimensions nominales des conducteurs couvertes par le présent document est:
– largeur: min. 2,0 mm max. 16,0 mm;
– épaisseur: min. 0,80 mm max. 5,60 mm.

Specifikacije za posebne vrste navijalnih žic - 60-1. del: S poliestrskim steklenim vlaknom prevlečena, nelakirana, gola ali emajlirana pravokotna bakrena žica, temperaturni indeks 155 (IEC 60317-60-1:2020)

General Information

• Status: Published
• Publication Date: 01-Sep-2020
• ICS: 29.060.10 - Wires
• ICS: 77.150.30 - Copper products
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 28-Aug-2020
• Due Date: 02-Nov-2020
• Completion Date: 02-Sep-2020
• Ref Project: EN IEC 60317-60-1:2020 - Specifications for particular types of winding wires - Part 60-1: Polyester glass-fibre wound fused, unvarnished, bare or enamelled rectangular copper wire, temperature index 155

Relations

• Replaces: SIST EN 60317-60:2012 - Specifications for particular types of winding wires - Part 60: Polyester glass fibres wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire, temperature index 155
• Effective Date: 03-Aug-2020

Overview

EN IEC 60317-60-1:2020 (CLC adoption of IEC 60317-60-1:2020) is a technical standard that specifies requirements for polyester glass‑fibre wound fused, unvarnished, bare or enamelled rectangular copper winding wire with a temperature index of 155. It defines acceptable conductor dimensions, materials, and test requirements for this specific type of rectangular copper wire used in electrical windings. The standard was approved by CENELEC in 2020 and replaces earlier parts of EN 60317-60.

Key topics and technical requirements

The standard sets out characteristic and test requirements relevant to production, inspection and use of these winding wires. Major topics include:

• Material and construction: polyester and electrical‑grade continuous filament glass yarn covering (polyester ≤ 50% by weight).
• Temperature rating: enamelled wire with a minimum temperature index 155; note that the heat shock test is inappropriate for this wire type (no heat shock temperature class can be established).
• Permitted conductor dimensions: width 2.0 mm – 16.0 mm, thickness 0.80 mm – 5.60 mm (nominal).
• Electrical and mechanical tests: electrical resistance, elongation, springiness, flexibility and adherence.
• Durability and reliability tests: cut‑through, resistance to abrasion, solvents, refrigerants, transformer oil, pin‑hole test and continuity of insulation.
• Electrical properties: breakdown voltage, dielectric dissipation factor.
• Processing properties: solderability, heat or solvent bonding.
• Packaging and marking: requirements for delivery and traceability.

These topics reference general methods in IEC 60317‑0‑8:2019 and test methods in the IEC 60851 series.

Applications

EN IEC 60317-60-1:2020 is intended for manufacturers, suppliers and users of flat rectangular copper winding wires used in:

• Transformers, motors and generators
• Power inductors and chokes
• Industrial coils and solenoids
• Any electrical equipment requiring high‑reliability rectangular conductors with a polyester/glass fibre covering and temperature index 155

Using this standard helps ensure consistent material quality, reliable electrical performance and compatibility with industry test procedures.

Who should use this standard

• Winding wire manufacturers and quality engineers
• Component and motor designers specifying winding materials
• Procurement and compliance teams buying enamelled rectangular wire
• Testing laboratories and certification bodies

Related standards

• IEC 60317 series (other specific winding wire specifications)
• IEC 60317‑0‑8:2019 (general requirements for polyester glass‑fibre wound rectangular wire)
• IEC 60851 series (winding wire test methods)
• IEC 60264 series (packaging of winding wires)

Keywords: EN IEC 60317-60-1:2020, polyester glass-fibre wound, rectangular copper wire, winding wires, temperature index 155, enamelled rectangular wire, winding wire specifications.

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2020
Nadomešča:
SIST EN 60317-60:2012
Specifikacije za posebne vrste navijalnih žic - 60-1. del: S poliestrskim steklenim
vlaknom prevlečena, nelakirana, gola ali emajlirana pravokotna bakrena žica,
temperaturni indeks 155 (IEC 60317-60-1:2020)
Specifications for particular types of winding wires - Part 60-1: Polyester glass-fibre
wound fused, unvarnished, bare or enamelled rectangular copper wire, temperature
index 155 (IEC 60317-60-1:2020)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten – Teil 60-
1:Flachdrähte aus Kupfer, mit Polyesterglasfasern umsponnen und verschmolzen, nicht
lackiert, blank oder lackisoliert, Temperaturindex 155 (IEC 60317-60-1:2020)
Spécifications pour types particuliers de fils de bobinage - Partie 60-1: Fil de section
rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre polyester fondues non
vernies, d'indice de température 155 (IEC 60317-60-1:2020)
Ta slovenski standard je istoveten z: EN IEC 60317-60-1:2020
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60317-60-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2020
ICS 29.060.10 Supersedes EN 60317-60:2012 (partially) and all of
its amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 60-1:
Polyester glass-fibre wound fused, unvarnished, bare or
enamelled rectangular copper wire, temperature index 155
(IEC 60317-60-1:2020)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 60-1: Fil de section rectangulaire en cuivre nu ou Wickeldrähten - Teil 60-1:Flachdrähte aus Kupfer, mit
émaillé, guipé de fibres de verre polyester fondues non Polyesterglasfasern umsponnen und verschmolzen, nicht
vernies, d'indice de température 155 lackiert, blank oder lackisoliert, Temperaturindex 155
(IEC 60317-60-1:2020) (IEC 60317-60-1:2020)
This European Standard was approved by CENELEC on 2020-07-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-60-1:2020 E

European foreword
The text of document 55/1850/FDIS, future edition 1 of IEC 60317-60-1, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-27
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-27
document have to be withdrawn
This document (partially) supersedes EN 60317-60:2012 and all of its amendments and corrigenda (if
any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-60-1:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60317-0-8 2019 Specifications for particular types of winding EN IEC 60317-0-8 2019
wires - Part 0-8: General requirements -
Polyester glass-fibre wound unvarnished and
fused, or resin or varnish impregnated, bare or
enamelled rectangular copper wire

IEC 60317-60-1 ®
Edition 1.0 2020-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 60-1: Polyester glass-fibre wound fused, unvarnished, bare or enamelled

rectangular copper wire, temperature index 155

Spécifications pour types particuliers de fils de bobinage –

Partie 60-1: Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres

de verre polyester fondues non vernies, d'indice de température 155

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10 ISBN 978-2-8322-8418-6

– 2 – IEC 60317-60-1:2020 © IEC 2020
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 6
3.2.1 Methods of test . 6
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 8
11 Resistance to abrasion . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 8
18 Heat or solvent bonding . 8
19 Dielectric dissipation factor . 8
20 Resistance to transformer oil .
...