SIST EN 266:2020
(Main)Wall coverings in roll form - Specification for textile wall coverings
Wall coverings in roll form - Specification for textile wall coverings
This European Standard specifies requirements for dimensions, adhesion of yarns and grades of
colour fastness to light, gives the symbols, to be used for marking purposes, for some of these
characteristics and also for matching, methods of application and removal, specifies
requirements for marking and gives the designation system. The marking requirements of this
standard are primarilyfor information of the consumer and to enable optimum use to be made of
the product.
The marking requirements of this standard are primarily for information of the consumer and to
enable optimum use to be made of the product.
This standard applies to textile wallcoverings supplied in rolls for hanging onto walls and ceilings
by means of an adhesive coverings the whole of the interface between the wallcovering and the
support. It does not apply to individual lengths of textile wallcovering cut at the retail point of
sale.
Excluded from this standard are rigid materials, materials not attached or not wholly attached by
adhesive, and non-decorative wallcoverings such as wall linings or those with special properties,
e.g. thermal or acoustic insulation.
Also excluded from this standard are wallpapers, wall vinyls and wallcoverings with a plastic
surface, which are dealt with in EN 233:1989.
Wandbekleidungen in Rollen - Festlegungen für Textilwandbekleidungen
Dieses Dokument:
- legt Anforderungen an die Maße, die Haftfestigkeit von Garnen und die Grade der Farbechtheit gegen Licht fest;
- enthält die Symbole, die zur Kennzeichnung einiger dieser Merkmale sowie des Ansatzes, der Verfahren für die Verarbeitung und das Entfernen zu verwenden sind;
- legt die Anforderungen an die Kennzeichnung fest;
- enthält das Bezeichnungssystem.
Die in diesem Dokument festgelegten Kennzeichnungen dienen in erster Linie der Verbraucherinformation und sollen die bestmögliche Anwendung des Produktes sicherstellen.
Dieses Dokument gilt für Textilwandbekleidungen in Rollen, die an Wänden und Decken mit einem Kleber angebracht werden, der die Fläche zwischen Wandbekleidung und Untergrund vollständig bedeckt.
Nicht Gegenstand dieses Dokuments sind harte Materialien, Materialien, die nicht oder nicht vollständig angeklebt werden, und Wandbekleidungen, die keine dekorative Funktion haben, z. B. Makulatur, oder Wandbekleidungen mit besonderen Eigenschaften, z. B. Wärme oder Schalldämmung.
Revêtements muraux en rouleaux - Spécification pour revêtements muraux textiles
Le présent document :
- spécifie les exigences relatives aux dimensions, à l’adhérence des fils et aux degrés de solidité des coloris à la lumière ;
- fournit les symboles, utilisés à des fins d’étiquetage, indiquant certaines de ces caractéristiques, ainsi que les raccords, méthodes de pose et de dépose ;
- spécifie les exigences relatives à l’étiquetage ;
- donne le système de désignation.
Les exigences relatives à l’étiquetage énoncées par le présent document sont principalement fournies à des fins d’information de l’utilisateur et pour permettre une utilisation optimale du produit.
Le présent document s’applique aux revêtements muraux textiles vendus en rouleaux destinés à être posés sur des murs et plafonds à l’aide d’une colle couvrant l’ensemble de l’interface entre le revêtement mural et le support.
Le présent document ne s’applique pas aux matériaux rigides, aux matériaux qui ne sont pas fixés - ou du moins entièrement - par une colle et aux revêtements muraux non décoratifs, tels que les revêtements d’apprêt ou des revêtements aux propriétés particulières, d’isolation thermique ou acoustique par exemple.
Stenske obloge v obliki zvitkov - Specifikacija za tekstilne stenske obloge
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 266:2020
01-december-2020
Nadomešča:
SIST EN 266:2000
Stenske obloge v obliki zvitkov - Specifikacija za tekstilne stenske obloge
Wall coverings in roll form - Specification for textile wall coverings
Wandbekleidungen in Rollen - Festlegungen für Textilwandbekleidungen
Revêtements muraux en rouleaux - Spécification pour revêtements muraux textiles
Ta slovenski standard je istoveten z: EN 266:2020
ICS:
91.180 Notranja zaključna dela Interior finishing
SIST EN 266:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 266:2020
---------------------- Page: 2 ----------------------
SIST EN 266:2020
EN 266
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2020
EUROPÄISCHE NORM
ICS 91.180 Supersedes EN 266:1991
English Version
Wall coverings in roll form - Specification for textile wall
coverings
Revêtements muraux en rouleaux - Spécification pour Wandbekleidungen in Rollen - Festlegungen für
revêtements muraux textiles Textilwandbekleidungen
This European Standard was approved by CEN on 5 February 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 266:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 266:2020
EN 266:2020 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensions . 5
4.1 General . 5
4.2 Usable dimensions . 6
4.3 Straightness and parallelity of the edges . 6
5 Adhesion of attached yarns . 6
6 Cleanability . 6
7 Colour fastness to light . 6
8 Matching, application, removal and miscellaneous symbols . 6
9 Marking . 7
9.1 Visible markings . 7
9.2 Additional markings . 7
9.3 Marking as heavy duty . 7
Annex A (normative) Sampling for testing . 8
Annex B (normative) Method of test for adhesion of attached yarns . 9
B.1 Principle . 9
B.2 Materials . 9
B.3 Apparatus . 9
B.3.1 Base machine . 9
B.3.2 Rubbing head . 9
B.4 Test pieces . 9
B.5 Procedure. 9
B.6 Assessment . 10
B.7 Expression of results . 10
Bibliography . 11
2
---------------------- Page: 4 ----------------------
SIST EN 266:2020
EN 266:2020 (E)
European foreword
This document (EN 266:2020) has been prepared by Technical Committee CEN/TC 99 “Wallcoverings”,
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2021, and conflicting national standards shall be
withdrawn at the latest by March 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 266:1991.
The main changes compared to the previous edition are listed below:
— update of normative references;
— modifications to Clause 4 Dimensions;
— update of the references in Clause 5;
— the references to Table 1 and the latter have been replaced by a global reference to the table of
EN 235 in Clauses 7 Colour fastness to light and 8 Matching, application, removal and miscellaneous
symbols;
— consistency of Clause 9 Marking has been improved;
— deletion of the former Annex B Method of measuring dimensions, while this is now referred to in
EN 12956:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 266:2020
EN 266:2020 (E)
Introduction
A textile wallcovering is a wallcovering, the front face of which consists of natural or synthetic fibrous or
filament materials such as yarns, woven fabrics, knitted fabrics, threads, ropes, braids, felts, etc., which
can be attached to a base web. A textile wallcovering is expected to have adequate strength such that it
can be hung satisfactorily in accordance with the instructions given by the supplier and using the
recommended adhesive.
There are many types of wallcovering and varied processes used in their manufacture. To ensure
satisfactory performance, it is important that installers follow the manufacturer's recommended hanging
instructions for each particular product.
Various grades of colour fastness to light of textile wallcoverings are permitted and symbols to indicate
these grades are given in this document, as well as symbols to indicate pattern matching, means of
application and methods of subsequent removal from the support. This will facilitate the selection by the
consumer of an appropriate wallcoverings. Other European standards on the vocabulary and symbols
used in the wallcovering industry, for finished wallpapers, wall vinyls and plastics wallcoverings, for
wallcoverings for subsequent decoration and for heavy duty wallcoverings are also published.
4
---------------------- Page: 6 ----------------------
SIST EN 266:2020
EN 266:2020 (E)
1 Scope
This document:
— specifi
...
SLOVENSKI STANDARD
oSIST prEN 266:2019
01-december-2019
Stenske obloge v obliki zvitkov - Specifikacija za tekstilne stenske obloge
Wall coverings in roll form - Specification for textile wall coverings
Wandbekleidungen in Rollen - Festlegungen für Textilwandbekleidungen
Revêtements muraux en rouleaux - Spécification pour revêtements muraux textiles
Ta slovenski standard je istoveten z: prEN 266
ICS:
91.180 Notranja zaključna dela Interior finishing
oSIST prEN 266:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 266:2019
---------------------- Page: 2 ----------------------
oSIST prEN 266:2019
DRAFT
EUROPEAN STANDARD
prEN 266
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2019
ICS 91.180 Will supersede EN 266:1991
English Version
Wall coverings in roll form - Specification for textile wall
coverings
Revêtements muraux en rouleaux - Spécification pour Wandbekleidungen in Rollen - Festlegungen für
revêtements muraux textiles Textilwandbekleidungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 99.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 266:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 266:2019
prEN 266:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensions . 5
4.1 General . 5
4.2 Dimensions . 6
4.3 Straightness and parallelity of the edges . 6
5 Adhesion of attached yarns . 6
6 Cleanability . 6
7 Colour fastness to light . 6
7.1 Grades of colour fastness to light of wallcoverings shall be determined in accordance
with definitions given in EN 235 . 6
7.2 The numerical rating for colour fastness to light shall be determined in accordance
with the requirements of EN ISO 105-B02 method A1. A wallcovering to this
document shall not have a rating of less than 4 (satisfactory). . 6
7.3 The symbols to be used for indicating the grade of colour fastness to light shall be as
given in EN235. 6
8 Matching, application, removal and miscellaneous symbols . 6
8.1 The symbols indicating pattern matching shall be as given in EN 235 . 6
8.2 The symbols indicating means of application of the adhesive shall be as given in EN
235 . 6
8.3 The symbols indicating the method of removal shall be as given in EN 235 . 6
8.4 The symbol indicating overlapping joins and double cutting shall be as given in
EN235 . 6
9 Marking . 7
9.1 Visible markings . 7
9.2 Additional markings . 7
9.3 Marking as heavy duty . 7
Annex A (normative) Sampling for testing . 8
Annex B (normative) Method of test for adhesion of attached yarns . 9
B.1 Principle . 9
B.2 Materials . 9
B.3 Apparatus . 9
B.3.1 Base Machine . 9
B.3.2 Rubbing head . 9
B.4 Test pieces . 9
B.5 Procedure. 9
B.6 Assessment . 10
B.7 Expression of results . 10
Biblography . 11
2
---------------------- Page: 4 ----------------------
oSIST prEN 266:2019
prEN 266:2019 (E)
European foreword
This document (prEN 266:2019) has been prepared by Technical Committee CEN/TC 99 “Wallcoverings”,
the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
3
---------------------- Page: 5 ----------------------
oSIST prEN 266:2019
prEN 266:2019 (E)
Introduction
A textile wallcovering is a wallcovering, the front face of which consists of natural or synthetic fibrous or
filament materials such as yarns, woven fabrics, knitted fabrics, threads, ropes, braids, felts, etc., which
can be attached to a base web. A textile wallcovering is expected to have adequate strength such that it
can be hung satisfactorily in accordance with the instructions given by the supplier and using the
recommended adhesive.
There are many types of wallcovering and varied processes used in their manufacture. To ensure
satisfactory performance, it is important that installers follow the manufacturer's recommended hanging
instructions for each particular product.
Various grades of colour fastness to light of textile wallcoverings are permitted and symbols to indicate
these grades are given in this document, as well as symbols to indicate pattern matching, means of
application and methods of subsequent removal from the support. This will facilitate the selection by the
consumer of an appropriate wallcoverings. Other European standards on the vocabulary and symbols
used in the wallcovering industry, for finished wallpapers, wall vinyls and plastics wallcoverings, for
wallcoverings for
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.