SIST EN ISO 9015-2:2012

Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)

The document specifies micro hardness tests on transverse sections of arc welded joints of metallic materials with high hardness gradients. It covers Vickers hardness tests in accordance with ISO 6507-1 and/or ISO 6507-2, normally with test loads of 0, 98 N to 49 N (HV 0, 1 to HV 5). It does not cover the hardness test as described in ISO 9015-1.

Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003)

Dieser Teil von ISO 9015 legt die Mikrohärteprüfungen an Querschliffen von Schweißverbindungen an metallischen Werkstoffen mit großen Härtegradienten fest. Er enthält Härteprüfungen nach Vickers nach ISO 6507-1 im Normalfall für Prüfkräfte von 0,98 N bis weniger als 49 N (HV 0,1 bis weniger als HV 5).
ANMERKUNG   Die Prüfung sollte so ausgeführt werden, dass die Bestimmung der Höchst- und/oder der Niedrigstwerte der Härte sowohl im Grundwerkstoff (im Falle von unterschiedlichen Metallen beider Grundwerkstoffe) als auch im Schweißgut sichergestellt ist.
In diesem Teil von ISO 9015 sind Härteprüfungen von Schweißungen mit Belastungen von 49,03 N und darüber, die in ISO 9015-1 beschrieben werden, nicht enthalten.
Dieser Teil von ISO 9015 ist nicht anwendbar für Härteprüfungen von sehr engen Schweißnähten, z. B. solche, die nach ISO 22826 üblicherweise mit Laser- und Elektronenstrahlschweißen erzeugt werden.

Essais destructifs des soudures sur matériaux métalliques - Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)

L'ISO 9015-2:2003 spécifie les essais de microdureté sur les sections transversales des assemblages soudés de matériaux métalliques à forts gradients de dureté. Elle concerne les essais de dureté Vickers conformément à l'ISO 6507-1, normalement sous des charges d'essai de 0,98 N à moins de 49,03 N (HV 0,1 à moins de HV 5).

Porušitveni preskusi zvarov na kovinskih materialih - Preskušanje trdote - 2. del: Preskušanje mikrotrdote zvarnih spojev (ISO 9015-2:2003)

Dokument določa preskušanje mikrotrdote na prečnih prerezih obločno varjenih spojev kovinskih materialov z visokimi gradienti trdote. Zajema preskušanje trdote po Vickersu v skladu z ISO 6507-1 in/ali ISO 6507-2, običajno s preskusnimi obremenitvami 0, 49 N do 98 N (HV 0, 1 do HV 5). Ne zajema preskusa trdote, kot je opisan v ISO 9015-1.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 24-Nov-2010
• Publication Date: 30-Nov-2011
• Withdrawal Date: 02-Mar-2016
• ICS: 25.160.40 - Welded joints and welds
• Technical Committee: VAR - Welding
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 02-Mar-2016
• Due Date: 25-Mar-2016
• Completion Date: 03-Mar-2016
• Ref Project: EN ISO 9015-2:2011 - Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)

Relations

• Replaced By: SIST EN ISO 9015-2:2016 - Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2016)
• Effective Date: 01-Apr-2016
• Replaces: SIST EN 1043-2:1998 - Destructive tests on welds in metallic materials - Hardness test - Part 2: Micro hardness testing on welded joints
• Effective Date: 01-Jan-2012
• Replaces: SIST EN 1043-2:1998 - Destructive tests on welds in metallic materials - Hardness test - Part 2: Micro hardness testing on welded joints
• Effective Date: 08-Jun-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Porušitveni preskusi zvarov na kovinskih materialih - Preskušanje trdote - 2. del: Preskušanje mikrotrdote zvarnih spojev (ISO 9015-2:2003)Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003)Essais destructifs des soudures sur matériaux métalliques - Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:EN ISO 9015-2:2011SIST EN ISO 9015-2:2012en,fr,de01-januar-2012SIST EN ISO 9015-2:2012SLOVENSKI
STANDARDSIST EN 1043-2:19981DGRPHãþD



SIST EN ISO 9015-2:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 9015-2
March 2011 ICS 25.160.40 Supersedes EN 1043-2:1996English Version
Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)
Essais destructifs des soudures sur matériaux métalliques -Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)
Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003) This European Standard was approved by CEN on 13 February 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 9015-2:2011: ESIST EN ISO 9015-2:2012



EN ISO 9015-2:2011 (E) 2 Contents Page Foreword .3 SIST EN ISO 9015-2:2012



EN ISO 9015-2:2011 (E) 3 Foreword The text of ISO 9015-2:2003 has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 9015-2:2011 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1043-2:1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 9015-2:2003 has been approved by CEN as a EN ISO 9015-2:2011 without any modification.
SIST EN ISO 9015-2:2012



SIST EN ISO 9015-2:2012



Reference numberISO 9015-2:2003(E)© ISO 2003
INTERNATIONAL STANDARD ISO9015-2First edition2003-11-15Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness testing of welded joints Essais destructifs des soudures sur matériaux métalliques —Essais de dureté — Partie 2: Essai de microdureté des assemblages soudés
SIST EN ISO 9015-2:2012



ISO 9015-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2003 — All rights reserved
SIST EN ISO 9015-2:2012



ISO 9015-2:2003(E) © ISO 2003 — All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Principle.1 4 Symbols and abbreviated terms.2 5 Preparation of test specimens.2 6 Test procedure.2 6.1 Rows of indentations (R).2 6.2 Individual indentations (E).3 7 Test results.3 8 Test report.3 Annex A (informative)
Example of a test report for rows of hardness tests (R) on welded joints.7 Annex B (informative)
Example of a test report for individual hardness tests (E) on welded joints.8 Bibliography.9
SIST EN ISO 9015-2:2012



ISO 9015-2:2003(E) iv © ISO 2003 — All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9015-2 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds. ISO 9015 consists of the following parts, under the general title Destructive tests on welds in metallic materials — Hardness testing:  Part 1: Hardness test on arc welded joints  Part 2: Microhardness testing of welded joints
SIST EN ISO 9015-2:2012



INTERNATIONAL STANDARD ISO 9015-2:2003(E) © ISO 2003 — All rights reserved 1 Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness t
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Porušitveni preskusi zvarov na kovinskih materialih - Preskušanje trdote - 2. del: Preskušanje mikrotrdote zvarnih spojev (ISO 9015-2:2003)Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003)Essais destructifs des soudures sur matériaux métalliques - Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:FprEN ISO 9015-2kSIST FprEN ISO 9015-2:2010en,fr,de01-november-2010kSIST FprEN ISO 9015-2:2010SLOVENSKI
STANDARD



kSIST FprEN ISO 9015-2:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 9015-2
August 2010 ICS 25.160.40 Will supersede EN 1043-2:1996English Version
Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints (ISO 9015-2:2003)
Essais destructifs des soudures sur matériaux métalliques -Essais de dureté - Partie 2: Essai de microdureté des assemblages soudés (ISO 9015-2:2003)
Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Härteprüfung - Teil 2: Mikrohärteprüfung an Schweißverbindungen (ISO 9015-2:2003) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 121.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 9015-2:2010: EkSIST FprEN ISO 9015-2:2010



FprEN ISO 9015-2:2010 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 9015-2:2010



FprEN ISO 9015-2:2010 (E) 3 Foreword The text of ISO 9015-2:2003 has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 9015-2:2010 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 1043-2:1996. Endorsement notice The text of ISO 9015-2:2003 has been approved by CEN as a FprEN ISO 9015-2:2010 without any modification. kSIST FprEN ISO 9015-2:2010



kSIST FprEN ISO 9015-2:2010



Reference numberISO 9015-2:2003(E)© ISO 2003
INTERNATIONAL STANDARD ISO9015-2First edition2003-11-15Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness testing of welded joints Essais destructifs des soudures sur matériaux métalliques —Essais de dureté — Partie 2: Essai de microdureté des assemblages soudés
kSIST FprEN ISO 9015-2:2010



ISO 9015-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2003 — All rights reserved
kSIST FprEN ISO 9015-2:2010



ISO 9015-2:2003(E) © ISO 2003 — All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Principle.1 4 Symbols and abbreviated terms.2 5 Preparation of test specimens.2 6 Test procedure.2 6.1 Rows of indentations (R).2 6.2 Individual indentations (E).3 7 Test results.3 8 Test report.3 Annex A (informative)
Example of a test report for rows of hardness tests (R) on welded joints.7 Annex B (informative)
Example of a test report for individual hardness tests (E) on welded joints.8 Bibliography.9
kSIST FprEN ISO 9015-2:2010



ISO 9015-2:2003(E) iv © ISO 2003 — All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9015-2 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds. ISO 9015 consists of the following parts, under the general title Destructive tests on welds in metallic materials — Hardness testing:  Part 1: Hardness test on arc welded joints  Part 2: Microhardness testing of welded joints
kSIST FprEN ISO 9015-2:2010



INTERNATIONAL STANDARD ISO 9015-2:2003(E) © ISO 2003 — All rights reserved 1 Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness testing of welded joints 1 Scope This part of ISO 9015 specifies microhardness tests on transverse sections of welded joints of metallic materials with high hardness gradients. It covers Vickers hardness tests in accordance with ISO 6507-1, normally with test loads of 0,98 N to less than 49 N (HV 0,1 to less than HV 5). NOTE Testing should be
...