SIST EN 3879:2023
(Main)Aerospace series - Metallic materials - Filler metal for welding - Technical specification
Aerospace series - Metallic materials - Filler metal for welding - Technical specification
This document defines the requirements for the ordering, manufacture, testing, inspection and delivery of all forms of filler metal. It shall be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.
Luft- und Raumfahrt - Metallische Werkstoffe - Schweisszusatz - Technische Lieferbedingungen
Dieses Dokument legt die Anforderungen an die Bestellung, Herstellung, Prüfung und Lieferung aller Formen von Schweißzusätzen fest. Es ist in Verbindung mit der entsprechenden EN Werkstoffnorm anzuwenden, sofern in der Zeichnung, Bestellung oder der Prüfanweisung nichts anderes angegeben ist.
Série aérospatiale - Matériaux métalliques - Métal d'apport de soudage - Spécification technique
Le présent document définit les exigences relatives aux commandes, à la fabrication, aux essais, aux contrôles et à la livraison de toutes les formes de métal d’apport. Il est applicable lorsqu'il est cité et conjointement avec la norme de matériaux EN sauf spécification contraire figurant sur le dessin, la commande ou la fiche d'essais.
Aeronavtika - Kovinski materiali - Kovinsko polnilo za varjenje - Tehnična specifikacija
Ta dokument opredeljuje zahteve za naročanje, proizvodnjo, preskušanje, pregled ter dobavo vseh vrst kovinskega polnila. Uporablja se, kadar se nanj sklicuje, in v povezavi s standardom za materiale EN, razen če je na skici, naročilu ali programu pregledov navedeno drugače.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 3879:2023
01-april-2023
Aeronavtika - Kovinski materiali - Kovinsko polnilo za varjenje - Tehnična
specifikacija
Aerospace series - Metallic materials - Filler metal for welding - Technical specification
Luft- und Raumfahrt - Metallische Werkstoffe - Schweisszusatz - Technische
Lieferbedingungen
Série aérospatiale - Matériaux métalliques - Métal d'apport de soudage - Spécification
technique
Ta slovenski standard je istoveten z: EN 3879:2023
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
49.025.05 Železove zlitine na splošno Ferrous alloys in general
SIST EN 3879:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 3879:2023
---------------------- Page: 2 ----------------------
SIST EN 3879:2023
EN 3879
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2023
EUROPÄISCHE NORM
ICS 25.160.20; 49.025.05; 49.025.15
English Version
Aerospace series - Metallic materials - Filler metal for
welding - Technical specification
Série aérospatiale - Matériaux métalliques - Métal Luft- und Raumfahrt - Metallische Werkstoffe -
d'apport de soudage - Spécification technique Schweisszusatz - Technische Lieferbedingungen
This European Standard was approved by CEN on 24 February 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3879:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Wording of order . 6
5 Health and safety . 6
6 Technical requirements . 6
6.1 General. 6
6.2 Qualification requirements . 7
6.3 Release requirements . 7
6.3.1 Release tests . 7
6.3.2 Retests . 7
6.3.3 Rejection . 8
6.3.4 Special tests . 8
6.3.5 Capability clause . 8
6.3.6 Statistical process control. 8
6.3.7 Inspection and test report . 8
6.4 Traceability . 8
Bibliography . 19
2
---------------------- Page: 4 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
European foreword
This document (EN 3879:2023) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this
document has received the approval of the National Associations and the Official Services of the
member countries of ASD, prior to its presentation to CEN.
This document shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2023, and conflicting national standards shall be
withdrawn at the latest by August 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject
of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such
patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Türkiye and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
Introduction
This document is part of the series of EN metallic material standards for aerospace applications.
The general organisation of this series is described in EN 4258.
4
---------------------- Page: 6 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
1 Scope
This document defines the requirements for the ordering, manufacture, testing, inspection and delivery
of all forms of filler metal. It shall be applied when referred to and in conjunction with the EN material
standard unless otherwise specified on the drawing, order or inspection schedule.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2032-001, Aerospace series — Metallic materials — Part 001: Conventional designation
EN 2032-2, Aerospace series — Metallic materials — Part 2: Coding of metallurgical condition in delivery
condition
EN 2078, Aerospace series — Metallic materials — Manufacturing schedule, inspection schedule,
inspection and test report — Definition, general principles, preparation and approval
EN 4058, Aerospace series — Filler rods and filler wires for welding in titanium and titanium alloys —
Diameter 0,5 mm ≤ D ≤ 5,0 mm — Dimensions
EN 4059, Aerospace series — Filler rods and filler wires for welding in steel —
Diameter 0,5 mm ≤ D ≤ 5,0 mm — Dimensions
EN 4060, Aerospace series — Filler rods and filler wires for welding in heat resisting alloys —
Diameter 0,5 mm ≤ D ≤ 5,0 mm — Dimensions
EN 4259, Aerospace series — Metallic materials — Definition of general terms
EN 4268, Aerospace series — Metallic materials — Heat treatment facilities — General requirements
ISO 544, Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of
1)
product, dimensions, tolerances and markings
2)
TR 4607, Aerospace series — Weldability test for weld filler metal wire
1)
Published by: ISO International Organization for Standardization http://www.iso.ch/.
2)
This project has been cancelled in July 2017.
5
---------------------- Page: 7 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 4259 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
filler metal for welding
is supplied in the form of:
— wire
wrought product of uniform solid section supplied in coil or on spools;
— rod
wire supplied in straight cut lengths
4 Wording of order
The order shall clearly indicate:
— quantities to be supplied;
— dates of delivery;
— material standard number;
— marking method;
— delivery condition;
— dimensions and tolerances or reference to an appropriate dimensional standard;
— forwarding address;
— nature and type of packing, if required;
— definition and frequency of any special tests and their retest procedures, if required.
5 Health and safety
The product in the delivery condition shall fulfil the health and safety laws of the area of the country
when and where it is to be delivered.
A product safety data sheet shall be available.
6 Technical requirements
6.1 General
The product shall be manufactured in accordance with the requirements of the relevant material
standard and the applicable requirements of this specification. A manufacturing schedule shall be
established and applied in accordance with EN 2078.
Product shall satisfy the requirements of the material standard and/or order and shall be free from
irregularities prejudicial to the subsequent manufacture or use of this product.
6
---------------------- Page: 8 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
Notwithstanding previous acceptance complying with this material standard, any product that is found,
at a later stage, to contain such defects shall be rejected. Instructions for the use of the material
standard are contained in EN 4258.
Unless otherwise specified, the requirements in Table 1 and in Table 2 shall apply in conjunction with
those of the relevant material standard. Table 1 relates to lines 1 to 29 (inclusive) of the material
standard and Table 2 relates to lines 30 onwards in which the sub-line format is also used. Lines 2 to 98
may also be opened in line 100 if the material standard details specific qualification requirements. If a
specific line number is not shown in Table 1 and Table 2, the requirement is stated in the material
standard and/or order.
6.2 Qualification requirements
Qualification requirements when invoked by the material standard and/or order are detailed in Table 1
and Table 2. Unless otherwise agreed between the manufacturer and purchaser the qualification phase
shall be run on the first 3 (three) batches.
6.3 Release requirements
6.3.1 Release tests
Release testing shall be the responsibility of the manufacturer.
The purchaser reserves the right to perform any of the inspections and/or tests required by the
material standard and/or order.
The test samples shall be representative of the product.
When required the manufacturer shall inform the purchaser of the planned dates for extraction of
samples and release testing in order that these operations may be witnessed.
Table 1 and Table 2 detail the requirements for each line of the material standard. Unless otherwise
specifically requested by the purchaser, a particular inspection and/or test for release shall be carried
out if corresponding acceptance criteria and/or values are stated in the applicable material standard
but see also 6.3.5 “Capability clause”.
6.3.2 Retests
If the test procedure or test piece preparation is faulty, testing shall be re-applied at the original
frequency after rectification of the original cause of failure.
When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall
be selected at twice the original frequency from the product, one of which shall be that on which the
original results were obtained unless already withdrawn by the manufacturer after suitable
identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted. If
one or more tests are unsatisfactory, the batch shall be:
— rejected; or
— 100 % retested and the conforming lengths accepted; or
— partially or fully re-heat treated if heat treatment can rectify the cause of the failure and tested as a
completely new batch except for chemical composition. No product or test sample shall be re-heat
treated more than twice.
7
---------------------- Page: 9 ----------------------
SIST EN 3879:2023
EN 3879:2023 (E)
6.3.3 Rejection
Any failure to meet the requirements of the material standard shall be cause for rejection.
6.3.4 Special tests
Special tests may be required by the purchaser. In such cases, the nature of the test, method, frequency
and technical requirements shall be specified on the order or inspection schedule and shall be mutually
agreed by the manufacturer and the purchaser.
6.3.5 Capability clause
Where the capability clause is invoked and where sufficient statistical evidence exists, the test need not
be carried out (unless specifically requested by the purchaser). However, this in no way reduces the
obligations of the manufacturer to fulfil the requirements. If subsequent testing indicates that the
product does not comply with the requirements, the batch shall be rejected.
If sufficient statistical evidence does not exist, the test shall be carried out at a frequency agreed
between the manufacturer and purchaser.
6.3.6 Statistical pro
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.