SIST EN 10292:2001/A1:2003
(Amendment)Continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming - Technical delivery conditions
Continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming - Technical delivery conditions
Correction of the max. carbon content for several grades.
Kontinuierlich schmelztauchveredeltes Band und Blech aus Stählen mit hoher Streckgrenze zum Kaltumformen - Technische Lieferbedingungen
Bandes et tôles en aciers a haute limite d'élasticité revetues en continu par immersion a chaud pour formage a froid - Conditions techniques de livraison
Jekleni trakovi in tanka pločevina s povečano napetostjo tečenja s površino, zaščiteno po postopkih vročega omakanja – Tehnični dobavni pogoji – Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 10292:2001/A1:2003
01-november-2003
-HNOHQLWUDNRYLLQWDQNDSORþHYLQDVSRYHþDQRQDSHWRVWMRWHþHQMDVSRYUãLQR
]DãþLWHQRSRSRVWRSNLKYURþHJDRPDNDQMD±7HKQLþQLGREDYQLSRJRML±'RSROQLOR
$
Continuously hot-dip coated strip and sheet of steels with higher yield strength for cold
forming - Technical delivery conditions
Kontinuierlich schmelztauchveredeltes Band und Blech aus Stählen mit hoher
Streckgrenze zum Kaltumformen - Technische Lieferbedingungen
Bandes et tôles en aciers a haute limite d'élasticité revetues en continu par immersion a
chaud pour formage a froid - Conditions techniques de livraison
Ta slovenski standard je istoveten z: EN 10292:2000/A1:2003
ICS:
77.140.50 3ORãþDWLMHNOHQLL]GHONLLQ Flat steel products and semi-
SROL]GHONL products
SIST EN 10292:2001/A1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 10292:2000/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2003
ICS 77.140.50
English version
Continuously hot-dip coated strip and sheet of steels with higher
yield strength for cold forming - Technical delivery conditions
Bandes et tôles en aciers à haute limite d'élasticité Kontinuierlich schmelztauchveredeltes Band und Blech aus
revêtues en continu par immersion à chaud pour formage à Stählen mit hoher Streckgrenze zum Kaltumformen -
froid - Conditions techniques de livraison Technische Lieferbedingungen
This amendment A1 modifies the European Standard EN 10292:2000; it was approved by CEN on 20 February 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10292:2000/A1:2003 E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 10292:2000/A1:2003 (E)
Contents
page
Foreword.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.