SIST EN 10169:2022
(Main)Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
Continuously organic coated (coil coated) steel flat products - Technical delivery conditions
This document specifies requirements for continuously organic coated (coil coated) steel flat products. It particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less than 600 mm and cut lengths (from sheet or strip).
NOTE National provisions can set up relationships between the performances of the coatings as required in this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
- tin mill products;
- electrical steels.
Kontinuierlich organisch beschichtete (bandbeschichtete) Flacherzeugnisse aus Stahl - Technische Lieferbedingungen
Dieses Dokument legt die Anforderungen an kontinuierlich organisch beschichtete (bandbeschichtete) Flacherzeugnisse aus Stahl fest, besonders im Hinblick auf die Gebrauchseigenschaften.
Bei den betroffenen Erzeugnissen handelt es sich um Breitband, aus Breitband geschnittenes Blech, längs geteiltes Breitband, gewalztes Band kleiner 600 mm Breite sowie (aus Band oder Blech) abgelängte Stäbe.
ANMERKUNG Diese Europäische Norm gilt nicht für kontinuierlich beschichtete Flacherzeugnisse aus:
- Verpackungsblech;
- Elektroband und -blech.
Produits plats en acier revêtus en continu de matières organiques (prélaqués) - Conditions techniques de livraison
Le présent document spécifie les exigences relatives aux produits plats en acier revêtus en continu de matières organiques (prélaqués) et, en particulier, les exigences de performance.
Les produits concernés sont des larges bandes, des tôles découpées dans les larges bandes, des larges bandes refendues, des bandes laminées en largeurs inférieures à 600 mm et des feuilles et bandes coupées à longueur.
NOTE Des réglementations nationales peuvent définir les relations entre les performances des revêtements telles qu’exigées dans le présent document et les atmosphères et ambiances extérieures requises pour un bâtiment étudié.
Le présent document n'est pas applicable aux produits plats revêtus en continu de matières organiques, fabriqués à l'aide de :
- produits étamés ;
- aciers pour applications électriques.
Z organskimi materiali kontinuirno prevlečeni ploščati jekleni izdelki v svitkih - Tehnični dobavni pogoji
Ta dokument določa zahteve za z organskimi materiali kontinuirno prevlečene ploščate jeklene izdelke v svitkih. Določa zlasti zahteve glede zmogljivosti.
Izdelki, ki jih zajema, so široki trakovi, plošče, rezane iz širokih trakov, rezani široki trakovi, trakovi v svitkih s širino manj kot 600 mm in rezane dolžine (iz plošč ali trakov).
OPOMBA: Nacionalne zahteve lahko vzpostavijo razmerja med učinkovitostjo premazov, kot je zahtevano v tem dokumentu, ter zunanjo atmosfero in okoljem, ki se zahteva za obravnavano zgradbo.
Ta dokument se ne uporablja za z organskimi materiali kontinuirno prevlečene ploščate izdelke v svitkih, izdelane iz:
– izdelkov iz bele pločevine;
– elektropločevine.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 10169:2022
01-maj-2022
Nadomešča:
SIST EN 10169:2011+A1:2012
Z organskimi materiali kontinuirno prevlečeni ploščati jekleni izdelki v svitkih -
Tehnični dobavni pogoji
Continuously organic coated (coil coated) steel flat products - Technical delivery
conditions
Kontinuierlich organisch beschichtete (bandbeschichtete) Flacherzeugnisse aus Stahl -
Technische Lieferbedingungen
Produits plats en acier revêtus en continu de matières organiques (prélaqués) -
Conditions techniques de livraison
Ta slovenski standard je istoveten z: EN 10169:2022
ICS:
25.220.60 Organske prevleke Organic coatings
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
SIST EN 10169:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 10169:2022
---------------------- Page: 2 ----------------------
SIST EN 10169:2022
EN 10169
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 25.220.60; 77.140.50 Supersedes EN 10169:2010+A1:2012
English Version
Continuously organic coated (coil coated) steel flat
products - Technical delivery conditions
Produits plats en acier revêtus en continu de matières Kontinuierlich organisch beschichtete
organiques (prélaqués) - Conditions techniques de (bandbeschichtete) Flacherzeugnisse aus Stahl -
livraison Technische Lieferbedingungen
This European Standard was approved by CEN on 24 January 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10169:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Designation . 12
5 Information to be supplied by the purchaser . 14
5.1 Mandatory information . 14
5.2 Options . 14
6 Requirements . 15
6.1 General. 15
6.2 General coating properties. 17
6.3 Special coating properties . 20
6.4 Freedom of defects . 25
7 Inspection . 25
7.1 Types of inspection and inspection documents . 25
7.2 Test units . 26
7.3 Type and number of tests . 26
7.4 Sampling . 26
7.5 Test methods . 26
7.6 Retests . 31
8 Marking . 31
9 Packing and dispatch . 31
10 Storage . 31
Annex A (informative) Types of ambience. 32
Annex B (informative) Coating materials. 35
Annex C (informative) Outdoor exposure sites . 37
Annex D (informative) Storage . 39
Bibliography . 40
2
---------------------- Page: 4 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
European foreword
This document (EN 10169:2022) has been prepared by Technical Committee CEN/TC 459/SC 9 “Coated
and uncoated flat products to be used for cold forming”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards shall
be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10169:2010+A1:2012.
In comparison with the previous edition, the following technical modifications have been made:
— addition of the requirement about a maximum six-month duration between production and
processing of the coil coated product;
— addition of the corrosion resistance category RC5+ corresponding to very high corrosivity
category C5 combining RC5-I and RC5-M that have been removed from this document;
— addition of the UV resistance category R ;
uv5
— addition of third party supervision for natural weathering tests if a certificate is required by the
purchaser;
— definition of a four-year test duration for corrosion resistance category RC5+;
— definition of requirements for natural outdoor UV radiation resistance tests;
— removal of Geleen from the list of natural outdoor corrosivity exposure sites;
— editorial improvements and updating of normative references.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
1 Scope
This document specifies requirements for continuously organic coated (coil coated) steel flat products. It
particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less
than 600 mm and cut lengths (from sheet or strip).
NOTE National provisions can set up relationships between the performances of the coatings as required in
this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
— tin mill products;
— electrical steels.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10020, Definition and classification of grades of steel
EN 10021, General technical delivery conditions for steel products
EN 10025-1, Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy
structural steels
EN 10048, Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels -
Tolerances on dimensions and shape
EN 10079, Definition of steel products
EN 10111, Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery
conditions
EN 10130, Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions
EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield
strength steel flat products for cold forming - Tolerances on dimensions and shape
EN 10139, Cold rolled uncoated mild steel narrow strip for cold forming - Technical delivery conditions
EN 10140, Cold rolled narrow steel strip - Tolerances on dimensions and shape
EN 10143, Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
EN 10152, Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery
conditions
EN 10204, Metallic products - Types of inspection documents
4
---------------------- Page: 6 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
EN 10268, Cold rolled steel flat products with high yield strength for cold forming - Technical delivery
conditions
EN 10338, Hot rolled and cold rolled non-coated products of multiphase steels for cold forming - Technical
delivery conditions
EN 10346, Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
EN 13523-1, Coil coated metals - Test methods - Part 1: Film thickness
EN 13523-2, Coil coated metals - Test methods - Part 2: Gloss
EN 13523-3, Coil coated metals - Test methods - Part 3: Colour difference and metamerism - Instrumental
comparison
EN 13523-4, Coil coated metals - Test methods - Part 4: Pencil hardness
EN 13523-5, Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
EN 13523-6, Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)
EN 13523-7, Coil coated metals - Test methods - Part 7: Resistance to cracking on bending (T-bend test)
EN 13523-8, Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)
EN 13523-10, Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water
condensation
EN 13523-12, Coil coated metals - Test methods - Part 12: Resistance to scratching
EN 13523-19, Coil coated metals - Test methods - Part 19: Panel design and method of atmospheric exposure
testing
EN 13523-21, Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels
EN 13523-26, Coil coated metals - Test methods - Part 26: Resistance to condensation of water
EN ISO 2815, Paints and varnishes - Buchholz indentation test (ISO 2815)
EN ISO 4618, Paints and varnishes - Terms and definitions (ISO 4618)
EN ISO 4628-2, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and
size of defects, and of intensity of uniform changes in appearance - Part 2: Assessment of degree of blistering
(ISO 4628-2)
EN ISO 4628-4, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and
size of defects, and of intensity of uniform changes in appearance - Part 4: Assessment of degree of cracking
(ISO 4628-4)
EN ISO 4628-5, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and
size of defects, and of intensity of uniform changes in appearance - Part 5: Assessment of degree of flaking
(ISO 4628-5)
EN ISO 8044, Corrosion of metals and alloys - Vocabulary (ISO 8044)
5
---------------------- Page: 7 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
EN ISO 12944-2, Paints and varnishes - Corrosion protection of steel structures by protective paint systems
- Part 2: Classification of environments (ISO 12944-2)
ISO 4997, Cold-reduced carbon steel sheet of structural quality
3 Terms and definitions
For the purpose of this document, the terms and definitions given in EN 10020, EN 10021, EN 10079,
EN 10204, EN ISO 4618, EN ISO 8044, EN ISO 12944-2 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
accessibility
ease of access to the steel components for the purpose of inspection and maintenance without any work
over and above that concerned with routine inspection
3.2
ambience
environmental conditions which prevail in the interior of the building
Note 1 to entry: These conditions determine the corrosivity category of the ambience and include different
parameters such as the air temperature, the relative humidity, the operating conditions in the building (e.g. use of
aggressive chemical products, refrigerated areas).
Note 2 to entry: The atmosphere surrounding the building can influence the ambience.
Note 3 to entry: Annex A gives an example of classification of types of ambience.
3.3
building interior application
application in buildings for which the concerned construction products (i.e. components of the building
fabric) are submitted to the influence of interior ambiences without significant exposure of any side of
the product to the influence of exterior atmospheres
Note 1 to entry: Building products include, for example: liner trays, ribbed profiles for roofing and cladding, curved
profiles, brake-pressed profiles, interior wall panels for partitions, ceiling panels, suspended frames (for suspended
ceilings), factory foamed (or with mineral wool) sandwich panels for cold rooms or rooms with controlled
ambience, interior door frames, interior metal doors, interior metal windows and for ceilings.
Note 2 to entry: Some coil coated products can be used for interior applications having special performance
requirements, e.g. lighting. In such cases, these particular requirements should also be considered in consultation
with the manufacturer.
Note 3 to entry: For interior building elements, it is important to consider the risk of corrosive attack on the reverse
side of the element. This can be especially important in double-skin assemblies (e.g. built up insulated cladding)
where the reverse side of the interior element is not easily accessible for maintenance and/or in situations where
the interior element is expected to provide long-term durability.
Note 4 to entry: Besides the requirements written in this document, there can be other international or national
requirements or regulations regarding fire, safety, food contact etc. that can be considered at the time of enquiry
and order.
6
---------------------- Page: 8 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
3.4
building exterior application
application in buildings for which the concerned products are submitted to the influence of exterior
atmospheres
Note 1 to entry: Building products include, for example, ribbed profiles for roofing and cladding, curved profiles,
brake-pressed profiles, concealed fix roofing and cladding, standing seam roofing, corrugated sheeting, cladding
goods, sandwich panels for roofing and cladding, roof tiles, accessories (flashings, trims), rainwater goods (gutters,
down pipes), metal doors and garage doors.
Note 2 to entry: For exterior building elements, it is important to consider the risk of corrosive attack on internal,
i.e. reverse side surfaces. In particular, buildings with wet or chemically polluted internal environments can require
a reverse side organic coating selected to provide enhanced corrosion protection.
Note 3 to entry: This can be especially important in double-skin assemblies (e.g. built-up insulated cladding) where
the reverse side of the exterior element is not easily accessible for maintenance and/or in situations where the
exterior element is expected to provide long-term durability.
Note 4 to entry: Besides the requirements written in this document, other international or national requirements
regarding reaction to fire, safety etc. can be agreed on at the time of enquiry and order.
3.5
coating flexibility
ability of a coating to follow without damaging the deformation of the substrate to which it is applied
Note 1 to entry: The flexibility is determined during cold forming of the coated product by the T-bend test.
Note 2 to entry: Cold forming is the process where the main forming is done without heating the working piece.
3.6
coating material
material comprising organic polymers, i.e. synthetic resin or plastics, to which pigments, additives and
solvents (if required) have generally been added, suitable for coil coating
Note 1 to entry: These can be paints (in liquid or powder form) that when applied form an opaque film or plastic
film providing protective, decorative and/or specific properties.
3.7
coating systems
3.7.1
coating system
combination of the coatings applied on either the top side or the reverse side consisting of one or more
coats of one or more coating materials, the designation of which is derived from the relevant coating
material
3.7.2
multiple-coat system
system comprising a priming coat, possibly intermediate coat(s) and a top coat with particular
requirements on appearance, corrosion protection, formability, etc.
3.8
nominal organic coating thickness
thickness of the organic coating system either on top side or on reverse side
7
---------------------- Page: 9 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
3.9
nominal thickness of an organic coated product
thickness of the metal substrate including metallic coating and excluding thickness of organic coating
system
3.10
coating types
3.10.1
backing coat
coating of any type on reverse side with no particular requirements on appearance, corrosion protection,
formability, etc.
Note 1 to entry: In the case of particular requirements, see 3.7.2.
3.10.2
film coating
plastic film applied to the substrate to which generally an adhesive and, if appropriate, a priming coat has
been applied beforehand
3.10.3
temporary film coating
strippable plastic film applied to the coated surface in order to afford a temporary protection against
mechanical damage (see also 6.1.2.3)
3.10.4
intermediate coat
coat between the priming coat and the top coat
3.10.5
priming coat
first coat of a multiple-coat system
Note 1 to entry: In the case of particular requirements, see 3.7.2.
3.10.6
top coat
finishing coat
final (uppermost) coat of a multiple-coat system
3.11
coil coating
process in which an (organic) coating material is applied on rolled metal strip in a continuous process
which includes cleaning, if necessary, and chemical pre-treatment of the metal surface and either: 1) one-
side or two-side, single or multiple application of (liquid) paints or coating powders which are
subsequently cured and/or 2) laminating with permanent plastic films
Note 1 to entry: Curing processes include those by convective or inductive heating or by radiation.
Note 2 to entry: Laminating with metal strip resulting in a sandwich system is possible.
Note 3 to entry: A single chemical pre-treatment and primer coat is possible.
8
---------------------- Page: 10 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
3.12
colour
sensation resulting from the visual perception of radiation of a given composition (related to
EN 13523-22)
Note 1 to entry: A colour is uniquely characterized for a defined observer and a defined light source as well as
illuminating and viewing geometry by the coordinates of a point in a space (colorimetric specification with
tristimulous values).
3.13
colour difference
magnitude and character of the visually perceived, i.e. qualitative, difference between two colours under
daylight and artificial light respectively, or the magnitude and direction of the (instrumentally) measured
and calculated difference of two colours (related to EN 13523-3)
3.14
corrosion protection (interior) category
CPI
category of coating which presents a certain level of corrosion protection, the choice of which depends
on the corrosivity category, the period of protection and the accessibility
3.15
corrosion resistance (outdoor) category
RC
category of product which presents a certain level of corrosion resistance, the choice of which depends
on the corrosivity category, the period of resistance and the accessibility
Note 1 to entry: Different categories of organic coil coated products for outdoor application are classified based on
their level of corrosion resistance. Criteria of classification are related to the level of their artificial (accelerated)
and natural outdoor corrosion resistance
Note 2 to entry: These conditions determine the corrosivity category and include both meteorological and
pollution parameters (EN ISO 12944-2).
Note 3 to entry: Environmental conditions can apply which are not typical of the region as a whole, e.g. in a rural
atmosphere close to a fossil fuel burning power generation plant, areas immediately downwind of the prevailing
wind direction can be subjected to an environment closer to urban or even industrial atmospheres. Such special
cases should be considered when organic coatings are chosen.
3.16
corrosivity category
C
category which indicates the corrosivity of the environment taking into account both atmospheric
conditions prevailing around a constituent element of a structure, and micro-environmental effects and
shall be used for the selection of the appropriate product (related to EN ISO 12944-2)
Note 1 to entry: The relationship between corrosivity categories and types of atmospheres is given in Table 6.
3.17
gloss
optical property of a surface, characterized by its ability to reflect light (related to EN 13523-2)
Note 1 to entry: For qualitative purposes, gloss ranges are often described by the terms “matt”, “low gloss” or
“semi-matt”, “satin”, “semi-gloss”, “gloss” and “high gloss”.
9
---------------------- Page: 11 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
3.18
specular gloss
ratio of the luminous flux from an object in the specular direction for a specified source and receptor
angle to the luminous flux from polished black glass (related to EN 13523-2)
3.19
master coil
coil from which sheets, cut lengths or two or more smaller coils are produced
3.20
organic coating
dry paint film of the coated product or the plastic film of the film/metal laminate
3.21
period of protection
time between the first exposure of the steel component and the moment at which maintenance works
need to be carried out to restore corrosion protection
Note 1 to entry: The need to restore corrosion protection is deemed to arise when failure of the coating has
occurred to the point where a significant amount (for example 5 %) of the component surface exhibits corrosion of
the substrate.
3.22
reverse side
opposite side of the top side (see 3.26)
3.23
saturated colour
colour with Chroma C* ≥ 40
Note 1 to entry: Chroma C* is defined by CIE 15:2004.
3.24
substrate
base material from rolled steel flat products, with or without metallic coating
3.25
time of wetness
period during which a coated surface is covered by a film of electrolyte that is capable of causing
atmospheric corrosion (see EN ISO 12944-2)
Note 1 to entry: Guidance value for time of wetness can be calculated from the temperature and relative humidity
by summing the hours where the relative humidity is above 80 % and, at the same time, the temperature is above
0 °C.
3.26
top side
side of the strip with the highest decorative demand and/or corrosion protection and which, in normal
production, is uppermost, respectively the exterior side of a coil
3.27
uncoated
condition in which parts of the surface of the substrate (e.g. one side of the strip) remain uncoated
10
---------------------- Page: 12 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
3.28
UV resistance category
R
uv
category of coating which presents a certain level of resistance to degradation by UV radiation
Note 1 to entry: Different categories of organic coil coated products for outdoor application are classified based on
their level of UV resistance. Criteria of classification are related to their level of artificial (accelerated) and natural
outdoor UV resistance according to the cumulative solar energy of the outdoor exposure site.
3.29
test specimen
sample produced on a full scale production line with the complete paint system
3.30
rural atmosphere
atmosphere prevailing in rural areas and small towns, without significant contamination by corrosive
agents such as sulphur dioxide and/or chlorides
Note 1 to entry: See also EN ISO 12944-2.
3.31
urban atmosphere
contaminated atmosphere prevailing in densely populated areas without significant industry
Note 1 to entry: See also EN ISO 12944-2.
Note 2 to entry: It has moderate concentrations of pollutants such as sulphur dioxide and/or chlorides.
3.32
industrial atmosphere
atmosphere contaminated by corrosive pollutants from local and regional industry (mainly sulphur
dioxide)
Note 1 to entry: See also EN ISO 12944-2.
3.33
marine atmosphere
atmosphere over and near the sea
Note 1 to entry: See also EN ISO 12944-2.
Note 2 to entry: A marine atmosphere will extend along a certain distance inland, depending on topography and
prevailing wind direction. It has a high content of sea-salt aerosols (mainly chlorides).
Note 3 to entry: The following explanations can be used for guidance:
— Low salinity is typical of areas located between 10 km and 20 km from the seashore.
— Moderate salinity is typical of areas located between 3 km and 10 km from the seashore.
— High salinity is typical of areas located from the seashore to 3 km inland.
Note 4 to entry: A distinction can be made between seashore and seafront. Seafront is defined as the place which is
submitted to direct attack by seawater and sea-salt aerosols.
11
---------------------- Page: 13 ----------------------
SIST EN 10169:2022
EN 10169:2022 (E)
3.34
industrial and marine atmosphere
atmosphere which combines industrial atmosphere (3.32) and marine atmosphere (3.33) conditions
Note 1 to entry: See also EN ISO 12944-2.
Note 2 to entry: In a given type of atmospheric environment, various corrosivity categories can be registered
depending on the location, i.e.:
— open air: both climatic influences and corrosive agents ca
...
SLOVENSKI STANDARD
oSIST prEN 10169:2021
01-maj-2021
Z organskimi materiali kontinuirno prevlečeni ploščati jekleni izdelki v svitkih -
Tehnični dobavni pogoji
Continuously organic coated (coil coated) steel flat products - Technical delivery
conditions
Kontinuierlich organisch beschichtete (bandbeschichtete) Flacherzeugnisse aus Stahl -
Technische Lieferbedingungen
Produits plats en acier revêtus en continu de matières organiques (prélaqués) -
Conditions techniques de livraison
Ta slovenski standard je istoveten z: prEN 10169
ICS:
25.220.60 Organske prevleke Organic coatings
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
oSIST prEN 10169:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10169:2021
---------------------- Page: 2 ----------------------
oSIST prEN 10169:2021
DRAFT
EUROPEAN STANDARD
prEN 10169
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2021
ICS 25.220.60; 77.140.50 Will supersede EN 10169:2010+A1:2012
English Version
Continuously organic coated (coil coated) steel flat
products - Technical delivery conditions
Produits plats en acier revêtus en continu de matières Kontinuierlich organisch beschichtete
organiques (prélaqués) - Conditions techniques de (bandbeschichtete) Flacherzeugnisse aus Stahl -
livraison Technische Lieferbedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 9.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10169:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Designation . 12
5 Information to be supplied by the purchaser . 14
5.1 Mandatory information . 14
5.2 Options . 15
6 Requirements . 15
6.1 General. 15
6.2 General coating properties. 17
6.3 Special coating properties . 20
6.4 Freedom of defects . 24
7 Inspection . 24
7.1 Types of inspection and inspection documents . 24
7.2 Test units . 25
7.3 Type and number of tests . 25
7.4 Sampling . 25
7.5 Test methods . 25
7.6 Retests . 29
8 Marking . 30
9 Packing and dispatch . 30
10 Storage . 30
Annex A (informative) Types of ambience. 31
Annex B (informative) Coating materials. 34
Annex C (informative) Outdoor exposure sites . 36
Annex D (informative) Storage . 38
Bibliography . 39
2
---------------------- Page: 4 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
European foreword
This document (prEN 10169:2021) has been prepared by Technical Committee CEN/TC 459/SC 9
“Coated and uncoated flat products to be used for cold forming”, the secretariat of which is held by
AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10169:2010+A1:2012.
This document is currently submitted to the CEN Enquiry.
In comparison with the previous edition, the following technical modifications have been made:
— addition of the requirement about a maximum six-month duration between production and
processing of the coil coated product;
— addition of the corrosion resistance category RC5+ corresponding to very high corrosivity
category C5 combining RC5-I and RC5-M that have been removed from this document;
— addition of the UV resistance category Ruv5;
— addition of third party supervision for natural weathering tests if a certificate is required by the
purchaser;
— definition of a four-year test duration for corrosion resistance category RC5+;
— definition of requirements for natural outdoor UV radiation resistance tests;
— removal of Geleen from the list of corrosivity natural outdoor exposure sites;
— editorial improvements and updating of normative references.
3
---------------------- Page: 5 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
1 Scope
This document specifies requirements for continuously organic coated (coil coated) steel flat products. It
particularly specifies the performance requirements.
The products covered are wide strip, sheet cut from wide strip, slit wide strip, strip rolled in widths less
than 600 mm and cut lengths (from sheet or strip).
NOTE National provisions can set up relationships between the performances of the coatings as required in
this document and the outdoor atmospheres and ambiances required for a relevant building under study.
This document is not applicable to continuously organic coated flat products made of:
— tin mill products;
— electrical steels.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10020, Definition and classification of grades of steel
EN 10021, General technical delivery conditions for steel products
EN 10025-1, Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy
structural steels
EN 10048, Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels -
Tolerances on dimensions and shape
EN 10079, Definition of steel products
EN 10111, Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery
conditions
EN 10130, Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions
EN 10131, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield
strength steel flat products for cold forming - Tolerances on dimensions and shape
EN 10139, Cold rolled uncoated mild steel narrow strip for cold forming — Technical delivery conditions
EN 10140, Cold rolled narrow steel strip - Tolerances on dimensions and shape
EN 10143, Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
EN 10152, Electrolytically zinc coated cold rolled steel flat products for cold forming - Technical delivery
conditions
4
---------------------- Page: 6 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
EN 10204, Metallic products - Types of inspection documents
EN 10268, Cold rolled steel flat products with high yield strength for cold forming — Technical delivery
conditions
EN 10338, Hot rolled and cold rolled non-coated products of multiphase steels for cold forming - Technical
delivery conditions
EN 10346, Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions
EN 13523-1, Coil coated metals - Test methods - Part 1: Film thickness
EN 13523-2, Coil coated metals - Test methods - Part 2: Gloss
EN 13523-3, Coil coated metals - Test methods - Part 3: Colour difference - Instrumental comparison
EN 13523-4, Coil coated metals - Test methods - Part 4: Pencil hardness
EN 13523-5, Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)
EN 13523-6, Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)
EN 13523-7, Coil coated metals - Test methods - Part 7: Resistance to cracking on bending (T-bend test)
EN 13523-8, Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)
EN 13523-10, Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water
condensation
EN 13523-12, Coil coated metals - Test methods - Part 12: Resistance to scratching
EN 13523-19, Coil coated metals - Test methods - Part 19: Panel design and method of atmospheric exposure
testing
EN 13523-21, Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels
EN 13523-26, Coil coated metals - Test methods - Part 26: Resistance to condensation of water
EN ISO 2815, Paints and varnishes - Buchholz indentation test (ISO 2815)
EN ISO 4618, Paints and varnishes - Terms and definitions (ISO 4618)
EN ISO 4628-2, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and
size of defects, and of intensity of uniform changes in appearance - Part 2: Assessment of degree of blistering
(ISO 4628-2)
EN ISO 4628-4, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and
size of defects, and of intensity of uniform changes in appearance - Part 4: Assessment of degree of cracking
(ISO 4628-4)
EN ISO 4628-5, Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and
size of defects, and of intensity of uniform changes in appearance - Part 5: Assessment of degree of flaking
(ISO 4628-5)
5
---------------------- Page: 7 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
EN ISO 8044, Corrosion of metals and alloys - Vocabulary (ISO 8044)
EN ISO 12944-2, Paints and varnishes - Corrosion protection of steel structures by protective paint systems
- Part 2: Classification of environments (ISO 12944-2)
ISO 4997, Cold-reduced carbon steel sheet of structural quality
3 Terms and definitions
For the purpose of this document, the terms and definitions given in EN 10020, EN 10021, EN 10079,
EN 10204, EN ISO 4618, EN ISO 8044, EN ISO 12944-2 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
accessibility
ease of access to the steel components for the purpose of inspection and maintenance without any work
over and above that concerned with routine inspection
3.2
ambience
environmental conditions which prevail in the interior of the building
Note 1 to entry: These conditions determine the corrosivity category of the ambience and include different
parameters such as the air temperature, the relative humidity, the operating conditions in the building (e.g. use of
aggressive chemical products, refrigerated areas).
Note 2 to entry: The atmosphere surrounding the building can influence the ambience.
Note 3 to entry: Annex A gives an example of classification of types of ambience.
3.3
building interior application
application in buildings for which the concerned construction products (i.e. components of the building
fabric) are submitted to the influence of interior ambiences without significant exposure of any side of
the product to the influence of exterior atmospheres
Note 1 to entry: Building products include, for example: liner trays, ribbed profiles for roofing and cladding, curved
profiles, brake-pressed profiles, interior wall panels for partitions, ceiling panels, suspended frames (for suspended
ceilings), factory foamed (or mineral wool) sandwich panels for cold rooms or rooms with controlled ambience,
interior door frames, interior metal doors, interior metal windows and for ceilings.
Note 2 to entry: Some coil coated products can be used for interior applications having special performance
requirements, e.g. lighting. In such cases, these particular requirements should also be considered in consultation
with the manufacturer.
Note 3 to entry: For interior building elements, it is important to consider the risk of corrosive attack on the reverse
side of the element. This can be especially important in double-skin assemblies (e.g. built up insulated cladding)
where the reverse side of the interior element is not easily accessible for maintenance and/or in situations where
the interior element is expected to provide long-term durability.
6
---------------------- Page: 8 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
Note 4 to entry: Besides the requirements written in this document, there can be other international or national
requirements or regulations regarding fire, safety, food contact etc. that can be considered at the time of enquiry
and order.
3.4
building exterior application
application in buildings for which the concerned products are submitted to the influence of exterior
atmospheres
Note 1 to entry: Building products include, for example, ribbed profiles for roofing and cladding, curved profiles,
brake-pressed profiles, concealed fix roofing and cladding, standing seam roofing, corrugated sheeting, cladding
goods, sandwich panels for roofing and cladding, roof tiles, accessories (flashings, trims), rainwater goods (gutters,
down pipes), metal doors and garage doors.
Note 2 to entry: For exterior building elements, it is important to consider the risk of corrosive attack on internal,
i.e. reverse side surfaces. In particular, buildings with wet or chemically polluted internal environments can require
a reverse side organic coating selected to provide enhanced corrosion protection.
Note 3 to entry: This can be especially important in double-skin assemblies (e.g. built-up insulated cladding) where
the reverse side of the exterior element is not easily accessible for maintenance and/or in situations where the
exterior element is expected to provide long-term durability.
Note 4 to entry: Besides the requirements written in this document, other international or national requirements
regarding reaction to fire, safety etc. can be agreed on at the time of enquiry and order.
3.5
coating flexibility
ability of a coating to follow without damaging the deformation of the substrate to which it is applied
Note 1 to entry: The flexibility is determined during cold forming of the coated product by the T-bend test.
Note 2 to entry: Cold forming is the process where the main forming is done without heating the working piece.
3.6
coating material
material comprising organic polymers, i.e. synthetic resin or plastics, to which pigments, additives and
solvents (if required) have generally been added, suitable for coil coating
Note 1 to entry: These can be paints (in liquid or powder form) that when applied form an opaque film or plastic
film providing protective, decorative and/or specific properties.
3.7
coating systems
3.7.1
coating system
combination of the coatings applied on either the top side or the reverse side consisting of one or more
coats of one or more coating materials, the designation of which is derived from the relevant coating
material
3.7.2
multiple-coat system
system comprising a priming coat, possibly intermediate coat(s) and a top coat with particular
requirements on appearance, corrosion protection, formability, etc
7
---------------------- Page: 9 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
3.8
nominal organic coating thickness
thickness of the organic coating system either on top side or on reverse side
3.9
coil coated product
metal substrate including metallic coating and excluding thickness of organic coating system
3.10
coating types
3.10.1
backing coat
coating of any type on reverse side with no particular requirements on appearance, corrosion protection,
formability, etc
Note 1 to entry In the case of particular requirements, see 3.7.2.
3.10.2
film coating
plastic film applied to the substrate to which generally an adhesive and, if appropriate, a priming coat has
been applied beforehand
3.10.3
temporary film coating
strippable plastic film applied to the coated surface in order to afford a temporary protection against
mechanical damage (see also 6.1.2.3)
3.10.4
intermediate coat
coat between the priming coat and the top coat
3.10.5
priming coat
first coat of a multiple-coat system
Note 1 to entry In the case of particular requirements, see 3.7.2 and 3.7.3.
3.10.6
top coat
finishing coat
final (uppermost) coat of a multiple-coat system
3.11
coil coating
process in which an (organic) coating material is applied on rolled metal strip in a continuous process
which includes cleaning, if necessary, and chemical pre-treatment of the metal surface and either:
— one-side or two-side, single or multiple application of (liquid) paints or coating powders which are
subsequently cured or/and
— laminating with permanent plastic films
Note 1 to entry: Curing processes include those by convective or inductive heating or by radiation.
8
---------------------- Page: 10 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
Note 2 to entry: Laminating with metal strip resulting in a sandwich system is possible.
Note 3 to entry: A one-coat chemical pre-treatment and priming coat is possible.
3.12
colour
sensation resulting from the visual perception of radiation of a given composition (related to
EN 13523-22)
Note 1 to entry: A colour is uniquely characterized for a defined observer and a defined light source as well as
illuminating and viewing geometry by the coordinates of a point in a space (colorimetric specification with
tristimulous values).
3.13
colour difference
magnitude and character of the visually perceived, i.e. qualitative, difference between two colours under
daylight and artificial light respectively, or the magnitude and direction of the (instrumentally) measured
and calculated difference of two colours (related to EN 13523-3)
3.14
corrosion protection (interior) category
CPI
category of coating which presents a certain level of corrosion protection, the choice of which depends
on the corrosivity category, the period of protection and the accessibility
3.15
corrosion resistance (outdoor) category
RC
category of product which presents a certain level of corrosion resistance, the choice of which depends
on the corrosivity category, the period of resistance and the accessibility
Note 1 to entry: Different categories of organic coil coated products for outdoor application classified following
their level of corrosion resistance are defined. Criteria of classification are related to their level of natural and
artificial outdoor corrosion resistance
Note 2 to entry: These conditions determine the corrosivity category and include both meteorological and
pollution parameters [EN ISO 12944-2]
Note 3 to entry: Environmental conditions can apply which are not typical of the region as a whole, e.g. in a rural
atmosphere close to a fossil fuel burning power generation plant, areas immediately downwind of the prevailing
wind direction can be subjected to an environment closer to urban or even industrial atmospheres. Such special
cases should be considered when organic coatings are chosen
3.16
corrosivity category
C
category which indicates the corrosivity of the environment taking into account both atmospheric
conditions prevailing around a constituent element of a structure, and micro-environmental effects and
shall be used for the selection of the appropriate product (related to EN ISO 12944-2)
Note 1 to entry: The relationship between corrosivity categories and types of atmospheres is given in Table 6.
9
---------------------- Page: 11 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
3.17
gloss
optical property of a surface, characterized by its ability to reflect light (related to EN 13523-2)
Note 1 to entry: For qualitative purposes, gloss ranges are often described by the terms “matt”, “low gloss” or
“semi-matt”, “satin”, “semi-gloss”, “gloss” and “high gloss”.
3.18
specular gloss
ratio of the luminous flux from an object in the specular direction for a specified source and receptor
angle to the luminous flux from polished black glass (related to EN 13523-2)
3.19
master coil
coil from which sheets, cut lengths or two or more smaller coils are produced
3.20
organic coating
dry paint film of the coated product or the plastic film of the film/metal laminate
3.21
period of protection
time between the first exposure of the steel component and the moment at which maintenance works
need to be carried out to restore corrosion protection
Note 1 to entry: The need to restore corrosion protection is deemed to arise when failure of the coating has
occurred to the point where a significant amount (for example 5 %) of the component surface exhibits corrosion of
the substrate.
3.22
reverse side
opposite side of the top side (see 3.26)
3.23
saturated colour
colour with Chroma C* ≥ 40
Note 1 to entry: Chroma C* is defined by CIE 15:2004.
3.24
substrate
base material from rolled steel flat products, with or without metallic coating
3.25
time of wetness
period during which a coated surface is covered by a film of electrolyte that is capable of causing
atmospheric corrosion (see EN ISO 12944-2)
Note 1 to entry: Guidance value for time of wetness can be calculated from the temperature and humidity relative
by summing the hours where the humidity relative is above 80 % and, at the same time, the temperature is above
0 °C.
10
---------------------- Page: 12 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
3.26
top side
side of the strip with the highest decorative demand and/or corrosion protection and which, in normal
production, is uppermost, respectively the exterior side of a coil
3.27
uncoated
condition in which parts of the surface of the substrate (e.g. one side of the strip) remain uncoated
3.28
UV resistance category
R
uv
category of coating which presents a certain level of resistance to degradation by UV radiation
Note 1 to entry: Different categories of organic coil coated products for outdoor application classified following
their level of UV resistance are defined. Criteria of classification are related to their level of natural and artificial
outdoor UV resistance with relation to the cumulative solar energy of the outdoor exposure site.
3.29
test specimen
sample produced on a full scale production line with the complete paint system
3.30
rural atmosphere
atmosphere prevailing in rural areas and small towns, without significant contamination by corrosive
agents such as sulphur dioxide and/or chlorides
Note 1 to entry: See also EN ISO 12944-2.
3.31
urban atmosphere
contaminated atmosphere prevailing in densely populated areas without significant industry
Note 1 to entry: See also EN ISO 12944-2.
Note 2 to entry: It has moderate concentrations of pollutants such as sulphur dioxide and/or chlorides.
3.32
industrial atmosphere
atmosphere contaminated by corrosive pollutants from local and regional industry (mainly sulphur
dioxide)
Note 1 to entry: See also EN ISO 12944-2.
11
---------------------- Page: 13 ----------------------
oSIST prEN 10169:2021
prEN 10169:2021 (E)
3.33
marine atmosphere
atmosphere over and near the sea
Note 1 to entry: See also EN ISO 12944-2.
Note 2 to entry: A marine atmosphere will extend along a certain distance inland, depending on topography and
prevailing wind direction. It has a high content of sea-salt aerosols (mainly chlorides).
Note 3 to entry: The following explanations can be used for guidance:
— Low salinity is typical of areas located between 10 km and 20 km from the seashore.
— Moderate salinity is typical of areas located between 3 km and 10 km from the seashore.
— High salinity is typical of areas located from the seashore to 3 km inland.
Note 4 to entry: A distinction can be made between seashore and seafront. Seafront is defined as the place which is
submitted to direct attack by seawater and sea-salt aerosols
3.34
industrial and marine atmosphere
atmosphere which combines industrial atmosphere (3.32) and marine atmosphere (3.33) conditions
Note 1 to entry: See also EN ISO 12944-2.
Note 2 to entry: In a given type of atmospheric environment, various corrosivity categories can be registered
depending on the location, i.e.:
— open air: both climatic influences and corrosive agents can act on metallic materials,
— under shelter: except rain, sunlight irradiation and solar gain, other climatic influences and corrosive
agents can act on metallic materials.
4 Designation
For the steel substrates covered by this document (see 6.1.1), the steel names are allocated in accordance
with EN 10027-1, the steel numbers are allocated in accordance with EN 10027-2.
The products covered by this document shall be designated as follows in the order given:
a) type of product (e.g. strip, sheet or cut length, see EN 10079);
b) reference to this document (prEN 10169:2021);
c) complete designation of the substrate, i.e.:
1) steel name or number,
2) type and nominal mass of the metal coating,
3) n
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.