SIST EN ISO 21003-5:2009
Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008)
Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008)
This part of ISO 21003 specifies the characteristics for the fitness for purpose of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1 of ISO 10508).
This standard covers a range of service conditions (application classes) and design pressure classes. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other parts of ISO 21003 it is applicable to multilayer pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations. For the purpose of this International Standard crosslinked polyethylene (PE-X) as well as adhesives are to be considered as thermoplastic materials.
Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation innerhalb von Gebäuden - Teil 5: Gebrauchstauglichkeit des Systems (ISO 21003-5:2008)
Dieser Teil der ISO 21003 legt die Eigenschaften für die Gebrauchstauglichkeit von Mehrschichtverbund-Rohrleitungssystemen fest, die in der Warm- und Kaltwasserinstallation innerhalb von Gebäuden für den Transport von Trink- oder Brauchwasser (Hausinstallation) sowie für Heizungsanlagen unter Berücksichtigung des betreffenden zulässigen Betriebsdruckes und der für die jeweilige Anwendungsklasse geltenden Temperaturen (siehe Tabelle 1, ISO 10508) eingesetzt werden.
Diese Norm enthält Festlegungen zu Anwendungsklassen, die sich auf Betriebsbedingungen beziehen, sowie Betriebsdruckklassen.
Es liegt in der Verantwortung des Käufers oder Auftraggebers, die geeignete Auswahl aus diesen Aspekten zu treffen unter Berücksichtigung der besonderen Anforderungen und aller zutreffenden nationalen Vorschriften sowie Verlegevorschriften und Regeln.
Diese Norm legt ebenfalls die Prüfparameter für die darin behandelten Prüfverfahren fest.
Nur bei gemeinsamer Anwendung aller Teile der ISO 21003 gelten diese für Mehrschichtverbund-Rohre, Formstücke, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Kunststoffen oder anderen Werkstoffen, die für die Warm- und Kaltwasserinstallationen vorgesehen sind.
ANMERKUNG Für die Anwendung dieser Internationalen Norm gelten sowohl vernetztes Polyethylen (PE-X) als auch Klebstoffe als thermoplastische Werkstoffe.
Systemes de canalisations multicouches pour installations d'eau chaude et froide a l'intérieur des bâtiments - Partie 5: Aptitude a l'emploi du systeme (ISO 21003-5:2008)
L'ISO 21003-5:2008 spécifie les caractéristiques d'aptitude à l'emploi des canalisations multicouches destinés aux installations d'eau chaude et froide à l'intérieur des bâtiments pour le transport de l'eau, destinée ou non à la consommation humaine (systèmes domestiques) et aux installations de chauffage, à des pressions et des températures correspondant à la classe d'application.
Elle spécifie aussi les paramètres d'essai pour les méthodes d'essai auxquelles il est fait référence dans la présente partie de l'ISO 21003.
L'ISO 21003 est une norme de produits de référence. Elle s'applique aux tubes, aux raccords, à leurs assemblages et aux assemblages avec des composants d'autres matières plastiques et non plastiques destinés aux installations d'eau chaude et froide. L'ISO 21003-5 est censée être utilisée uniquement conjointement avec toutes les autres parties de l'ISO 21003.
Večslojni cevni sistemi za napeljave z vročo in hladno vodo v stavbah - 5. del: Ustrezanje zahtevam za uporabnost sistema (ISO 21003-5:2008)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mehrschichtverbund-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation innerhalb von Gebäuden - Teil 5: Gebrauchstauglichkeit des Systems (ISO 21003-5:2008)Systemes de canalisations multicouches pour installations d'eau chaude et froide a l'intérieur des bâtiments - Partie 5: Aptitude a l'emploi du systeme (ISO 21003-5:2008)Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008)91.140.60Sistemi za oskrbo z vodoWater supply systems23.040.01Deli cevovodov in cevovodi na splošnoPipeline components and pipelines in generalICS:Ta slovenski standard je istoveten z:EN ISO 21003-5:2008SIST EN ISO 21003-5:2009en01-januar-2009SIST EN ISO 21003-5:2009SLOVENSKI
STANDARD
SIST EN ISO 21003-5:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 21003-5July 2008ICS 23.040.01; 91.140.60 English VersionMultilayer piping systems for hot and cold water installationsinside buildings - Part 5: Fitness for purpose of the system (ISO21003-5:2008)Systèmes de canalisations multicouches pour installationsd'eau chaude et froide à l'intérieur des bâtiments - Partie 5:Aptitude à l'emploi du système (ISO 21003-5:2008)Mehrschichtverbund-Rohrleitungssysteme für die Warm-und Kaltwasserinstallation innerhalb von Gebäuden - Teil 5:Gebrauchstauglichkeit des Systems (ISO 21003-5:2008)This European Standard was approved by CEN on 15 June 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 21003-5:2008: ESIST EN ISO 21003-5:2009
EN ISO 21003-5:2008 (E) 2 Contents Page Foreword.3
SIST EN ISO 21003-5:2009
EN ISO 21003-5:2008 (E) 3 Foreword This document (EN ISO 21003-5:2008) has been prepared by Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 21003-5:2008 has been approved by CEN as a EN ISO 21003-5:2008 without any modification.
SIST EN ISO 21003-5:2009
SIST EN ISO 21003-5:2009
Reference numberISO 21003-5:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO21003-5First edition2008-07-01Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system Systèmes de canalisations multicouches pour installations d'eau chaude et froide à l'intérieur des bâtiments — Partie 5: Aptitude à l'emploi du système
SIST EN ISO 21003-5:2009
ISO 21003-5:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
SIST EN ISO 21003-5:2009
ISO 21003-5:2008(E) © ISO 2008 – All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Symbols and abbreviated terms.2 5 Fitness for purpose of the joints and the piping system.3 5.1 General.3 5.2 Internal pressure test.3 5.3 Bending test.4 5.4 Pull-out test.5 5.5 Thermal cycling test.6 5.6 Pressure cycling test.6 5.7 Leaktightness under vacuum.7 Annex A (normative)
List of reference product standards.8 Bibliography.9
SIST EN ISO 21003-5:2009
ISO 21003-5:2008(E) iv © ISO 2008 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21003-5 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies. ISO 21003 consists of the following parts, under the general title Multilayer piping systems for hot and cold water installations inside buildings: ⎯ Part 1: General ⎯ Part 2: Pipes ⎯ Part 3: Fittings ⎯ Part 5: Fitness for purpose of the system ⎯ Part 7: Guidance for the assessment of conformity [Technical Specification] NOTE ISO 21003 does not include a Part 4: Ancillary equipment, or a Part 6: Guidance for installation. SIST EN ISO 21003-5:2009
ISO 21003-5:2008(E) © ISO 2008 – All rights reserved vIntroduction The system standard of which this is Part 5 specifies the requirements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside buildings. In respect of potential adverse effects on the quality of water intended for human consumption caused by the products covered by ISO 21003: ⎯ no information is provided as to whether the products may be used without restriction in any of the member states of the EU or EFTA; ⎯ it should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of these products remain in force. Requirements and test methods for components of the piping system are specified in ISO 21003-1, ISO 21003-2 and ISO 21003-3. ISO/TS 21003-7 gives guidance on the assessment of conformity. This part of ISO 21003 specifies the characteristics for fitness for purpose. For ancillary equipment, separate standards can apply. Guidance on installation of plastics piping systems made from various materials intended to be used for hot and cold water installations is given in ENV 12108. Other system standards which, at the date of publication of this part of ISO 21003, had been published for plastics piping systems used for the same application are listed in Annex A.
SIST EN ISO 21003-5:2009
SIST EN ISO 21003-5:2009
INTERNATIONAL STANDARD ISO 21003-5:2008(E) © ISO 2008 – All rights reserved 1Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system 1 Scope This part of ISO 21003 specifies the characteristics for the fitness for purpose of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 21003:2008). It also specifies the test parameters for the test methods referred to in this part of ISO 21003. ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. Th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.