SIST EN ISO 19892:2018
(Main)Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of joints to pressure cycling (ISO 19892:2011)
Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of joints to pressure cycling (ISO 19892:2011)
ISO 19892:2011 specifies a method for testing the resistance of joints to pressure cycling. It is applicable to piping systems based on thermoplastics pipes intended to be used in hot and cold water applications.
Kunststoff-Rohrleitungssysteme - Rohre und Formstücke aus Thermoplasten für Warm- und Kaltwasser - Prüfverfahren für die Widerstandsfähigkeit von Verbindungen gegen Druckwechselbeanspruchung (ISO 19892:2011)
Systèmes de canalisations en plastiques - Tubes en matières thermoplastiques et raccords pour l'eau chaude et froide - Méthode d'essai de la résistance des assemblages aux cycles de pression (ISO 19892:2011)
L'ISO 19892:2011 spécifie une méthode permettant d'évaluer la résistance des assemblages à des cycles de pression. Elle s'applique aux systèmes de canalisations constitués de tubes thermoplastiques destinés à être utilisés pour des applications d'eau chaude et froide.
Cevni sistemi iz polimernih materialov - Plastomerne cevi in fitingi za hladno in toplo vodo - Preskusna metoda za ugotavljanje odpornosti spojev proti cikličnim spremembam tlaka (ISO 19892:2011)
Standard ISO 19892:2011 določa metodo za preskušanje odpornosti spojev proti cikličnim spremembam tlaka. Uporablja se za sisteme s termoplastičnimi cevmi, namenjene za uporabo s sistemi za toplo in hladno vodo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19892:2018
01-december-2018
1DGRPHãþD
SIST EN 12295:2000
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY3ODVWRPHUQHFHYLLQILWLQJL]DKODGQRLQ
WRSORYRGR3UHVNXVQDPHWRGD]DXJRWDYOMDQMHRGSRUQRVWLVSRMHYSURWLFLNOLþQLP
VSUHPHPEDPWODND ,62
Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test
method for the resistance of joints to pressure cycling (ISO 19892:2011)
Kunststoff-Rohrleitungssysteme - Rohre und Formstücke aus Thermoplasten für Warm-
und Kaltwasser - Prüfverfahren für die Widerstandsfähigkeit von Verbindungen gegen
Druckwechselbeanspruchung (ISO 19892:2011)
Systèmes de canalisations en plastiques - Tubes en matières thermoplastiques et
raccords pour l'eau chaude et froide - Méthode d'essai de la résistance des assemblages
aux cycles de pression (ISO 19892:2011)
Ta slovenski standard je istoveten z: EN ISO 19892:2018
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 19892:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19892:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 19892:2018
EN ISO 19892
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 23.040.60; 83.080.20 Supersedes EN 12295:1999
English Version
Plastics piping systems - Thermoplastics pipes and fittings
for hot and cold water - Test method for the resistance of
joints to pressure cycling (ISO 19892:2011)
Systèmes de canalisations en plastiques - Tubes en Kunststoff-Rohrleitungssysteme - Rohre und
matières thermoplastiques et raccords pour l'eau Formstücke aus Thermoplasten für Warm- und
chaude et froide - Méthode d'essai de la résistance des Kaltwasser - Prüfverfahren für die
assemblages aux cycles de pression (ISO 19892:2011) Widerstandsfähigkeit von Verbindungen gegen
Druckwechselbeanspruchung (ISO 19892:2011)
This European Standard was approved by CEN on 1 October 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19892:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19892:2018
EN ISO 19892:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19892:2018
EN ISO 19892:2018 (E)
European foreword
The text of ISO 19892:2011 has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids” of the International Organization for Standardization
(ISO) and has been taken over as EN ISO 19892:2018 by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12295:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19892:2011 has been approved by CEN as EN ISO 19892:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 19892:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 19892:2018
INTERNATIONAL ISO
STANDARD 19892
First edition
2011-11-01
Plastics piping systems —
Thermoplastics pipes and fittings for hot
and cold water — Test method for the
resistance of joints to pressure cycling
Systèmes de canalisations en plastiques — Tubes en matières
thermoplastiques et raccords pour l’eau chaude et froide — Méthode
d’essai de la résistance des assemblages aux cycles de pression
Reference number
ISO 19892:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 19892:2018
ISO 19892:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19892:2018
ISO 19892:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has be
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.