SIST EN ISO 11296-2:2018

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)

This Part 2 of EN 13566, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of non-pressure drainage and sewerage networks. It covers;
-   homogeneous-wall (HW) pipes made of polyethylene (PE) or polypropylene (PP),
-   structured-wall (SW) pipes of the corrugated double-wall type of construction as defined in Annex B, whose structural layer(s) is (are) made of PE or PP,
-   jointing of pipe lengths by means of butt fusion (HW)  ) or electrofusion (SW),
-   fabricated and injection-moulded fittings made of PE, PP and poly(vinyl chloride) (PVC-U).
NOTE    The grouting procedure is outside the scope of this standard.

Kunststoff-Rohrleitungssysteme zur Renovierung von erdverlegten drucklosen Entwässerungsnetzen (Freispiegelleitungen) - Teil 2: Rohrstrang-Lining (ISO 11296-2:2018)

Diese Internationale Norm legt in Verbindung mit Teil 1 die Anforderungen und Prüfverfahren für Rohre und Formstücke fest, die Teil eines Kunststoff-Rohrleitungssystems sind und die als Rohrstrang-Lining bei der Renovierung erdverlegter druckloser Entwässerungsnetze eingebaut werden. Drei verschiedenen Arten von PE-Rohren können dafür angewendet werden:
   einschichtige PE-Vollwandrohre (Nenn-Außendurchmesser, dn), mit Kennzeichnungsstreifen;
   PE-Rohre mit koextrudierten Schichten auf der Innen- oder Außenseite des Rohres oder beides (Gesamt-Außendurchmesser, dn), wie in Anhang A festgelegt, worin alle Schichten den gleichen MRS-Wert haben;
   beschichtete PE-Rohre (Außendurchmesser, dn) mit einer abziehbaren, zusammenhängenden, thermoplastischen Zusatzschicht auf der Rohr-Außenseite („beschichtetes Rohr“), siehe Anhang A.
Zusätzlich wird betrachtet:
   Verbindung von Rohrlängen durch Stumpfschweißen;
   vorgefertigte und Spritzguss-Formstücke aus PE.

Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression - Partie 2: Tubage par tuyau continu avec espace annulaire (ISO 11296-2:2018)

ISO 11296-2:2018, lu conjointement avec l'ISO 11296‑1, spécifie les exigences et les méthodes d'essai pour des tuyaux et raccords intégrés aux systèmes de canalisations en plastique installés sous forme de tuyaux continus et utilisés pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression. Il s'applique aux tuyaux en PE de trois types différents:
-      tuyaux en PE monocouches à paroi compacte (diamètre extérieur nominal, dn), y compris les bandes d'identification éventuelles;
-      tuyaux en PE avec des couches co-extrudées à l'extérieur et/ou à l'intérieur du tuyau (diamètre extérieur total, dn), tels que spécifiés dans l'Annexe A, toutes les couches ayant la même classification MRS;
-      tuyaux revêtus de PE (diamètre extérieur, dn) comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau («tuyau revêtu»), voir l'Annexe A.
ISO 11296-2:2018 couvre également:
-      l'assemblage des longueurs de tuyau par soudage bout à bout;
-      les raccords en PE façonnés et moulés par injection.

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 2. del: Oblaganje z neprekinjenimi cevmi (ISO 11296-2:2018)

Ta 2. del standarda EN 13566, bran v povezavi s 1. delom, določa zahteve in preskusne metode za cevi in fitinge, ki so del plastičnih cevnih sistemov, nameščenih kot neprekinjene cevi pri obnovi omrežij za odvodnjavanje in kanalizacijo, ki obratujejo brez tlaka. Zajema:
– homogene stenske cevi (HW), izdelane iz polietilena (PE) ali polipropilena (PP);
– konstrukcijske stenske cevi (SW) valovitega dvojno-stenskega tipa konstrukcije, kot je določen v dodatku B, katerih konstrukcijske plasti so izdelane iz PE ali PP;
– spajanje dolžin cevi s soležnim taljenjem (HW) ali elektrofuzijo (SW);
– oblikovane in brizgano lite fitinge iz PE, PP in poli(vinilklorida) (PVC-U).
OPOMBA: Postopek nanašanja malte ne spada na področje uporabe tega standarda.

General Information

• Status: Published
• Public Enquiry End Date: 19-Sep-2016
• Publication Date: 19-Mar-2018
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 91.140.80 - Drainage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Mar-2018
• Due Date: 06-May-2018
• Completion Date: 20-Mar-2018
• Ref Project: EN ISO 11296-2:2018 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)

Relations

• Replaces: SIST EN 13566-2:2006 - Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes
• Effective Date: 01-Apr-2018

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11296-2:2018
01-april-2018
1DGRPHãþD
SIST EN 13566-2:2006
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo za obratovanje brez tlaka (vodi s prosto gladino) - 2.
del: Oblaganje z neprekinjenimi cevmi (ISO 11296-2:2018)
Plastics piping systems for renovation of underground non-pressure drainage and
sewerage networks - Part 2: Lining with continuous pipes (ISO 11296-2:2018)
Kunststoff-Rohrleitungssysteme zur Renovierung von erdverlegten drucklosen
Entwässerungsnetzen (Freispiegelleitungen) - Teil 2: Rohrstrang-Lining (ISO 11296-
2:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sans pression - Partie 2:
Tubage par tuyau continu avec espace annulaire (ISO 11296-2:2018)
Ta slovenski standard je istoveten z: EN ISO 11296-2:2018
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 11296-2:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11296-2:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 11296-2:2018


EN ISO 11296-2
EUROPEAN STANDARD

NORME EUROPÉENNE

February 2018
EUROPÄISCHE NORM
ICS 23.040.45; 23.040.20; 91.140.80; 93.030 Supersedes EN 13566-2:2005
English Version

Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks - Part 2:
Lining with continuous pipes (ISO 11296-2:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme zur Renovierung von
rénovation des réseaux de branchements et de erdverlegten drucklosen Entwässerungsnetzen
collecteurs d'assainissement enterrés sans pression - (Freispiegelleitungen) - Teil 2: Rohrstrang-Lining (ISO
Partie 2: Tubage par tuyau continu avec espace 11296-2:2018)
annulaire (ISO 11296-2:2018)
This European Standard was approved by CEN on 10 September 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11296-2:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11296-2:2018
EN ISO 11296-2:2018 (E)
Contents Page
European foreword . 3


2

---------------------- Page: 4 ----------------------

SIST EN ISO 11296-2:2018
EN ISO 11296-2:2018 (E)
European foreword
This document (EN ISO 11296-2:2018) has been prepared by Technical Committee ISO/TC 138
“Rehabilitation of pipeline systems” in collaboration with Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall
be withdrawn at the latest by August 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13566-2:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11296-2:2018 has been approved by CEN as EN ISO 11296-2:2018 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 11296-2:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 11296-2:2018
INTERNATIONAL ISO
STANDARD 11296-2
First edition
2018-02
Plastics piping systems for renovation
of underground non-pressure
drainage and sewerage networks —
Part 2:
Lining with continuous pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
de branchements et de collecteurs d'assainissement enterrés sans
pression —
Partie 2: Tubage par tuyau continu avec espace annulaire
Reference number
ISO 11296-2:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 11296-2:2018
ISO 11296-2:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11296-2:2018
ISO 11296-2:2018(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 2
4.1 Symbols . 2
4.2 Abbreviated terms . 2
5 Pipes at the “M” stage . 2
5.1 Material . 2
5.2 General characteristics . 2
5.3 Material characteristics . 3
5.4 Geometrical characteristics . 3
5.5 Mechanical characteristics. 3
5.6 Physical characteristics . 3
5.7 Jointing . 3
5.8 Marking . 3
5.9 Regional requirements for pipes . 3
6 Fittings at the “M” stage . 3
6.1 Requirements . 3
6.2 Marking . 3
6.3 Regional requirements for fittings . 3
7 Ancillary components . 3
8 Fitness for purpose of the system for pipes and fittings at the “I” stage .4
9 Installation practice . 4
9.1 Preparatory work . 4
9.2 Storage, handling and transport . 4
9.3 Equipment . 4
9.3.1 Butt fusion equipment and de-beading equipment. 4
9.3.2 Pipe rollers . 5
9.3.3 Winching and rod-pulling equipment . 5
9.3.4 Pipe entry guides . 5
9.3.5 Electrofusion equipment . 5
9.3.6 Inspection equipment . 5
9.3.7 Lifting equipment . 5
9.4 Installation . 5
9.5 Process-related inspection and testing . 6
9.6 Lining termination . 6
9.7 Reconnection to the existing pipeline system . 6
9.8 Final inspection and testing . 6
9.9 Documentation . 6
Annex A (normative) Layered pipes . 7
Bibliography . 8
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11296-2:2018
ISO 11296-2:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, Subcommittee SC 8, Rehabilitation of pipeline systems.
A list of all parts in the ISO 11296 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 11296-2:2018
ISO 11296-2:2018(E)

Introduction
This document is part of a system standard for plastics piping systems of various materials used for
renovation of existing pipelines in a specified application area. System standards for renovation dealing
with the following applications are either available or in preparation:
— ISO 11296, Plastics piping systems for renovation of underground non-pressure drainage and sewerage
networks (this application);
— ISO 11297, Plastics piping systems for renovation of underground drainage and sewerage networks
under pressure;
— ISO 11298, Plastics piping systems for renovation of underground water supply networks;
— ISO 11299, Plastics piping systems for renovation of underground gas supply networks.
These system standards are distinguished from system standards for conventionally installed plastics
piping systems by the requirement to verify certain characteristics in the “as installed” condition,
after site processing. This is in addition to verification of characteristics of
...