SIST EN 13480-5:2024
(Main)Metallic industrial piping - Part 5: Inspection and testing
Metallic industrial piping - Part 5: Inspection and testing
This document specifies the requirements for inspection and testing of industrial piping as specified in EN 13480-1:2024 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480-3:2024 and EN 13480-6:2024 (if applicable), and fabricated and installed in accordance with EN 13480-4:2024.
Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Dieses Dokument legt die Anforderungen an die Prüfungen von metallischen industriellen Rohrleitungen fest nach den Festlegungen in EN 13480-1:2024, die bei Fertigung und Verlegung nach EN 13480-4:2024 an einzelnen, nach EN 13480-3:2024 und EN 13480-6:2024 (falls anwendbar) ausgelegten vorgefertigten Baugruppen (Spools) oder Rohrleitungssystemen einschließlich Halterungen, durchzuführen sind.
Tuyauteries industrielles métalliques - Partie 5: Inspection et contrôle
Le présent document spécifie les exigences relatives à l'inspection et au contrôle des tuyauteries industrielles telles que spécifiées dans l’EN 13480-1:2024, à exécuter sur les éléments de tuyauteries préfabriqués ou sur les réseaux de tuyauteries, supports compris, conçus conformément à l’EN 13480-3:2024 et à l’EN 13480-6:2024 (le cas échéant), et fabriqués et installés conformément à l’EN 13480-4:2024.
Kovinski industrijski cevovodi - 5. del: Pregled in preskušanje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Nadomešča:
SIST EN 13480-5:2018
SIST EN 13480-5:2018/A1:2019
SIST EN 13480-5:2018/A2:2021
Kovinski industrijski cevovodi - 5. del: Pregled in preskušanje
Metallic industrial piping - Part 5: Inspection and testing
Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Tuyauteries industrielles métalliques - Partie 5: Inspection et contrôle
Ta slovenski standard je istoveten z: EN 13480-5:2024
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13480-5
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2024
EUROPÄISCHE NORM
ICS 23.040.01 Supersedes EN 13480-5:2017
English Version
Metallic industrial piping - Part 5: Inspection and testing
Tuyauteries industrielles métalliques - Partie 5: Metallische industrielle Rohrleitungen - Teil 5: Prüfung
Inspection et contrôle
This European Standard was approved by CEN on 9 July 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-5:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 6
3 Terms and definitions . 7
4 Symbols and abbreviations . 7
5 Determination of inspection and testing requirements . 7
5.1 General . 7
5.2 Classification of piping . 7
6 Design review . 7
7 In-process inspection and testing . 8
7.1 General . 8
7.2 Materials and formed pressure retaining parts. 8
7.2.1 General . 8
7.2.2 Verification of material . 8
7.2.3 Verification of formed pressure retaining parts . 8
7.2.4 Non-destructive testing of formed parts . 8
7.2.5 Destructive testing of formed parts. 12
7.3 Welding . 12
7.3.1 Review of welding documents . 12
7.3.2 Inspection before welding . 12
7.3.3 Testing and inspection during welding . 13
7.3.4 Inspection after welding . 13
7.3.5 Inspection of built up pipe ends. 13
7.4 Heat treatment . 13
8 Non-destructive testing of welds . 13
8.1 Application of NDT . 13
8.1.1 General . 13
8.1.2 Examination of weld quality by sample inspection . 14
8.1.3 Imperfections revealed by sample inspection. 14
8.2 Circumferential butt, branch, fillet and seal welds . 15
8.2.1 Extent of testing . 15
8.2.2 Dissimilar metal joints . 17
8.2.3 Transverse cracks . 17
8.3 Longitudinal welds . 17
8.4 Testing methods . 17
8.4.1 General . 17
8.4.2 Quality level . 17
8.4.3 Personnel qualification . 18
8.4.4 Selection of NDT methods and testing techniques . 18
8.4.5 Testing techniques and acceptance levels . 19
8.5 Reports . 19
8.6 Weld repairs. 19
9 Final assessment and documentation . 19
9.1 General . 19
9.2 Final inspection . 19
9.2.1 General . 19
9.2.2 Visual inspection before the proof test . 19
9.2.3 Visual inspection after the proof test . 20
9.2.4 Review of the manufacturing documents . 20
9.3 Proof test. 20
9.3.1 General . 20
9.3.2 Hydrostatic pressure test . 20
9.3.3 Pneumatic pressure test . 23
9.3.4 Other tests . 25
9.3.5 Documentation of the proof test . 25
9.4 Documentation . 25
9.4.1 Final documentation package . 25
9.4.2 Design and manufacturing documentation package . 27
9.4.3 Operating instructions . 27
9.4.4 Documentation for the purchaser . 27
10 Declaration. 27
Annex A (informative) Declaration of compliance with EN 13480 . 28
A.1 Declaration for design . 28
A.2 Declaration for fabrication, installation and testing . 29
A.3 Declaration for compliance for piping with EN 13480 . 30
Annex B (informative) Initial Leak Test . 31
B.1 Initial Service Leak Test . 31
B.1.1 General . 31
B.1.2 Examination Procedure for service fluid gas or vapor . 31
B.1.3 Examination Procedure for service fluid liquid . 31
B.2 Initial Leak Test . 31
Annex Y (informative) History of EN 13480-5 . 32
Y.1 Differences between EN 13480-5:2017 and EN 13480-5:2024 . 32
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2014/68/EU aimed to be covered . 33
Bibliography . 34
European foreword
This document (EN 13480-5:2024) has been prepared by Technical Committee CEN/TC 267 “Industrial piping
and pipelines”, the secretariat of which is
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.