iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 50160:2023/A1:2025

(Amendment)

Voltage characteristics of electricity supplied by public electricity networks

Voltage characteristics of electricity supplied by public electricity networks

This document specifies the main characteristics of the voltage at a network user's supply terminals in public low voltage, medium, high, and extra-high voltage AC electricity networks under normal operating conditions. This document specifies the limits or values within which the voltage characteristics can be expected to remain at any supply terminal in public European electricity networks, only. Industrial networks are excluded from the scope of EN 50160. NOTE 1 If non-public networks (e.g. residential quarters, energy communities, office centres, shopping centres) have similar end-users as public networks, it is strongly advised to apply the same requirements as for public networks. This document does not apply under abnormal operating conditions, including the following: a) a temporary supply arrangement to keep network users supplied during conditions arising as a result of a fault, maintenance and construction work, or to minimize the extent and duration of a loss of supply; b) in the case of non-compliance of a network user's installation or equipment with the relevant standards or with the technical requirements for connection, established either by the public authorities or the network operator, including the limits for the emission of conducted disturbances; NOTE 2 A network user’s installation can include load and generation. c) in exceptional situations, in particular: 1) exceptional weather conditions and other natural disasters; 2) third party interference; 3) acts by public authorities, 4) industrial actions (subject to legal requirements); 5) force majeure; 6) power shortages resulting from external events. The voltage characteristics given in this document refer to conducted disturbances in public electric power networks. They are not intended to be used as electromagnetic compatibility (EMC) levels or product emission limits. Power quality is related to EMC in several ways – especially because compliance with power quality requirements depends on the control of cumulative effect of electromagnetic emissions from all/multiple equipment and/or installations. Therefore, the voltage characteristics given in this document gives guidance for specifying requirements in equipment product standards and in installation standards. NOTE 3 The performance of equipment might be impaired if it is subjected to supply conditions which are not specified in the equipment product standard. NOTE 4 This document can be superseded in total or in part by the terms of a contract between the individual network user and the network operator. The sharing of complaint management and problem mitigation costs between the involved parties is outside the scope of EN 50160.

Merkmale der Spannung in öffentlichen Energieversorgungsnetzen

Caractéristiques de la tension fournie par les réseaux publics d'electricité

Značilnosti napetosti v javnih razdelilnih omrežjih - Dopolnilo A1

General Information

Status
Published
Public Enquiry End Date
09-Sep-2024
Publication Date
17-Mar-2025
ICS
29.020 - Electrical engineering in general
29.240.01 - Power transmission and distribution networks in general
Technical Committee
NTF - Electricity energy supply systems
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Jan-2025
Due Date
22-Mar-2025
Completion Date
18-Mar-2025
Ref Project
EN 50160:2022/A1:2025 - Voltage characteristics of electricity supplied by public electricity networks

Relations

Amends
SIST EN 50160:2023 - Voltage characteristics of electricity supplied by public distribution networks
Effective Date
15-Aug-2023

Buy Standard

EN 50160:2023/A1:2025EN 50160:2023/A1:2025
PreviousNext
Amendment
EN 50160:2023/A1:2025
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2025
Značilnosti napetosti v javnih razdelilnih omrežjih - Dopolnilo A1
Voltage characteristics of electricity supplied by public electricity networks
Merkmale der Spannung in öffentlichen Energieversorgungsnetzen
Caractéristiques de la tension fournie par les réseaux publics d'electricité
Ta slovenski standard je istoveten z: EN 50160:2022/A1:2025
ICS:
29.240.01 Omrežja za prenos in Power transmission and
distribucijo električne energije distribution networks in
na splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50160:2022/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM January 2025
ICS 29.020
English Version
Voltage characteristics of electricity supplied by public electricity
networks
Caractéristiques de la tension fournie par les réseaux Merkmale der Spannung in öffentlichen
publics d'electricité Energieversorgungsnetzen
This amendment A1 modifies the European Standard EN 50160:2022; it was approved by CENELEC on 2023-12-29. CENELEC members
are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the status of a
national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50160:2022/A1:2025 E

Contents Page
European foreword . 3
1 Modifications to Clause 3 . 4
1.1 Modification to 3.2.2 . 4
1.2 Modification to 3.2.11 . 4
1.3 Modification to 3.3.5 . 4
1.4 Modification to 3.3.6 . 4
2 Modifications to Clause 4 . 4
2.1 Modification to 4.1 . 4
2.2 Modification to 4.2.2.2 . 5
2.3 Modification to 4.2.4 . 5
2.4 Modification to 4.2.5 . 5
2.5 Modifications to 4.4.2 . 5
3 Modifications to Clause 5 . 6
3.1 Modification to 5.1 . 6
3.2 Modification to 5.2.2.2 . 6
3.3 Modification to 5.2.4 . 6
3.4 Modification to 5.2.5 . 6
3.5 Modifications to 5.4.2 . 6
4 Modifications to Clause 6 . 6
4.1 Modification to 6.1 . 6
4.2 Modification to 6.2.4 . 6
4.3 Modification to 6.2.5 . 7
4.4 Modification to 6.3.2.6 . 7
5 Modifications to Clause 7 . 7
5.1 Modification to 7.1 . 7
5.2 Modification to 7.2.4 . 7
5.3 Modification to 7.2.5 . 7
5.4 Modification to 7.3.2.4 . 7
6 Modification in Annex B . 7
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 50160:2023(Main)
Voltage characteristics of electricity supplied by public distribution networks
EN 50160:2022

1.1   Scope
This document specifies the main characteristics of the voltage at a network user's supply terminals in public low voltage, medium, high, and extra-high voltage AC electricity networks under normal operating conditions. This document specifies the limits or values within which the voltage characteristics can be expected to remain at any supply terminal in public European electricity networks, only.
NOTE 1   If non-public networks (e.g. residential quarters, energy communities, office centres, shopping centres) have similar end-users as public networks, it is strongly advised to apply the same requirements as for public networks.
NOTE 2   Industrial networks are excluded from the scope of EN 50160, only the connection to the supply terminals of the public network is relevant, here.
This document does not apply under abnormal operating conditions, including the following:
a)   a temporary supply arrangement to keep network users supplied during conditions arising as a result of a fault, maintenance and construction work, or to minimize the extent and duration of a loss of supply.
b)   in the case of non-compliance of a network user's installation or equipment with the relevant standards or with the technical requirements for connection, established either by the public authorities or the network operator, including the limits for the emission of conducted disturbances.
NOTE 4   A network user’s installation can include load and generation.
c)   in exceptional situations, in particular:
1)   exceptional weather conditions and other natural disasters;
2)   third party interference;
3)   acts by public authorities,
4)   industrial actions (subject to legal requirements);
5)   force majeure;
6)   power shortages resulting from external events.
The voltage characteristics given in this document refer to conducted disturbances in public electric power networks. They are not intended to be used as electromagnetic compatibility (EMC) levels or product emission limits.
Power quality is related to EMC in several ways – especially because compliance with power quality requirements depends on the control of cumulative effect of electromagnetic emissions from all/multiple equipment and/or installations. Therefore, the voltage characteristics given in this document gives guidance for specifying requirements in equipment product standards and in installation standards.
NOTE 5   The performance of equipment might be impaired if it is subjected to supply conditions which are not specified in the equipment product standard.
NOTE 6   This document can be superseded in total or in part by the terms of a contract between the individual network user and the network operator.
NOTE 7   The sharing of complaint management and problem mitigation costs between the involved parties is outside the scope of EN 50160.
Measurement methods to be applied in this document are described in EN 61000 4 30.
1.2   Object
The object of this document is to define, describe and specify the characteristics of the supply voltage concerning:
a)   Frequency;
b)   Magnitude;
c)   Waveform;
d)   Symmetry of the line voltages.
This document also covers the continuous characteristics of the supply voltage and other foreseeable phenomena which may influence the voltage characteristics, such as e.g. operational communication, monitoring or measurement signals which are transmitted via power lines.
These characteristics are subject to variations during the normal operation of a supply system due to changes of load, disturbances generated by certain equipment and the occurrence of faults which are mainly caused by external events.
The characteristics vary in a manner which is random in time, with reference to any specific supply terminal, and random in location, with reference to any given instant of time. Because of these variations, the values given in this document for the characteristics can be expected to be exceeded on a small number of occasions.
[...]

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61936-2:2023(Main)
Power installations exceeding 1 kV AC and 1,5 kV DC - Part 2: DC
EN IEC 61936-2:2023

This part of IEC 61936 provides, in a convenient form, requirements for the design and the
erection of DC installations in systems with nominal voltages above 1,5 kV DC, so as to provide
safety and proper functioning for the use intended.
For the purpose of interpreting this document, a DC installation is considered to be one of the
following:
a) A converter station or DC switching station;
b) one (or more) DC generating or storage unit(s), such as solar farms or battery storage units,
located on a single site, the DC installation includes DC equipment and cables with all
associated power electronics, controlgear, switchgear and all electrical auxiliary systems.
Connections between DC generating or storage units located on different sites are excluded;
c) DC installation erected on offshore facilities for the purpose of generation, transmission,
distribution and/or storage of electricity; or
d) DC transition station (between overhead lines and underground cable or between different
sections of underground cables).
This International Standard does not apply to the design and erection of any of the following:
– overhead and underground lines between separate installations;
– electric railways;
– mining equipment and installations;
– installations on ships according to IEC 60092 series and offshore units according to
IEC 61892 series, which are used in the offshore petroleum industry for drilling, processing
and storage purposes;
– electrostatic equipment (e.g. electrostatic precipitators, spray-painting units);
– test sites;
– medical equipment, e.g. medical X-ray equipment;
– valve hall or converter hall.
This document does not apply to the requirements for carrying out live working on electrical
installations.
This document does not apply to the design of factory-built, type-tested thyristor valves, VSC
valves and switchgear for which separate IEC standards exist.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST IEC 60050-692:2023(Main)
International Electrotechnical Vocabulary (IEV) - Part 692: Generation, transmission and distribution of electrical energy - Dependability and quality of service of electric power systems
IEC 60050-692:2017

IEC 60050-692:2017 gives the terminology used when considering the dependability and quality of service of electric power systems. The concepts are categorized according to the following sections:
- system concepts;
- operating states of electric power systems;
- failures in electric power systems;
- outages of electric power systems equipment;
- outage occurrences in electric power systems;
- state durations and availability related concepts;
- interruptions in electric power systems;
- selected customer interruption measures;
- bulk electric power system load/energy curtailments;
- bulk electric system failures and measures;
- supply performance measures.
This terminology is consistent with the terminology developed in the other specialized parts of the IEV.
It has the status of a horizontal standard in accordance with IEC Guide 108.

  • Standard
    140 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    127 pages
    English and French language
    sale 15% off
SIST
SIST EN 50160:2023(Main)
Voltage characteristics of electricity supplied by public distribution networks
EN 50160:2022

1.1   Scope
This document specifies the main characteristics of the voltage at a network user's supply terminals in public low voltage, medium, high, and extra-high voltage AC electricity networks under normal operating conditions. This document specifies the limits or values within which the voltage characteristics can be expected to remain at any supply terminal in public European electricity networks, only.
NOTE 1   If non-public networks (e.g. residential quarters, energy communities, office centres, shopping centres) have similar end-users as public networks, it is strongly advised to apply the same requirements as for public networks.
NOTE 2   Industrial networks are excluded from the scope of EN 50160, only the connection to the supply terminals of the public network is relevant, here.
This document does not apply under abnormal operating conditions, including the following:
a)   a temporary supply arrangement to keep network users supplied during conditions arising as a result of a fault, maintenance and construction work, or to minimize the extent and duration of a loss of supply.
b)   in the case of non-compliance of a network user's installation or equipment with the relevant standards or with the technical requirements for connection, established either by the public authorities or the network operator, including the limits for the emission of conducted disturbances.
NOTE 4   A network user’s installation can include load and generation.
c)   in exceptional situations, in particular:
1)   exceptional weather conditions and other natural disasters;
2)   third party interference;
3)   acts by public authorities,
4)   industrial actions (subject to legal requirements);
5)   force majeure;
6)   power shortages resulting from external events.
The voltage characteristics given in this document refer to conducted disturbances in public electric power networks. They are not intended to be used as electromagnetic compatibility (EMC) levels or product emission limits.
Power quality is related to EMC in several ways – especially because compliance with power quality requirements depends on the control of cumulative effect of electromagnetic emissions from all/multiple equipment and/or installations. Therefore, the voltage characteristics given in this document gives guidance for specifying requirements in equipment product standards and in installation standards.
NOTE 5   The performance of equipment might be impaired if it is subjected to supply conditions which are not specified in the equipment product standard.
NOTE 6   This document can be superseded in total or in part by the terms of a contract between the individual network user and the network operator.
NOTE 7   The sharing of complaint management and problem mitigation costs between the involved parties is outside the scope of EN 50160.
Measurement methods to be applied in this document are described in EN 61000 4 30.
1.2   Object
The object of this document is to define, describe and specify the characteristics of the supply voltage concerning:
a)   Frequency;
b)   Magnitude;
c)   Waveform;
d)   Symmetry of the line voltages.
This document also covers the continuous characteristics of the supply voltage and other foreseeable phenomena which may influence the voltage characteristics, such as e.g. operational communication, monitoring or measurement signals which are transmitted via power lines.
These characteristics are subject to variations during the normal operation of a supply system due to changes of load, disturbances generated by certain equipment and the occurrence of faults which are mainly caused by external events.
The characteristics vary in a manner which is random in time, with reference to any specific supply terminal, and random in location, with reference to any given instant of time. Because of these variations, the values given in this document for the characteristics can be expected to be exceeded on a small number of occasions.
[...]

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61936-1:2021(Main)
Power installations exceeding 1 kV AC and 1,5 kV DC - Part 1: AC
EN IEC 61936-1:2021

This part of IEC 61936 provides requirements for the design and the erection of electrical power
installations in systems with nominal voltages exceeding 1 kV AC and nominal frequency up to
and including 60 Hz, so as to provide safety and proper functioning for the use intended.
For the purpose of interpreting this document, an electrical power installation is considered to
be one of the following:
a) substation, including substation for railway power supply;
b) electrical power installations on mast, pole and tower, switchgear and/or transformers
located outside a closed electrical operating area;
c) one (or more) power station(s) located on a single site, the electrical power installation
includes generators and transformers with all associated switchgear and all electrical
auxiliary systems. Connections between generating stations located on different sites are
excluded;
d) the electrical system of a factory, industrial plant or other industrial, agricultural, commercial
or public premises;
e) electrical power installations on offshore facilities for the purpose of generation,
transmission, distribution and/or storage of electricity;
f) transition towers/poles (between overhead lines and underground lines).
The electrical power installation includes, among others, the following equipment:
– rotating electrical machines;
– switchgear;
– transformers and reactors;
– converters;
– cables;
– wiring systems;
– batteries;
– capacitors;
– earthing systems;
– buildings and fences which are part of a closed electrical operating area;
– associated protection, control and auxiliary systems;
– large air core reactor.
NOTE 1 In general, equipment standards take precedence over the requirements of this document.
This document does not apply to the design and erection of any of the following:
– overhead and underground lines between separate electrical power installations;
– electrified railway tracks and rolling stock;
– mining equipment and installations;
fluorescent lamp installations;
– installations on ships according to IEC 60092 (all parts) and offshore units according to
IEC 61892 (all parts), which are used in the offshore petroleum industry for drilling,
processing and storage purposes;
– electrostatic equipment (e.g. electrostatic precipitators, spray-painting units);
– test sites;
– medical equipment, e.g. medical X-ray equipment.
This document does not apply to the design of prefabricated, type-tested switchgear and high
voltage/low voltage prefabricated substation, for which separate IEC standards exist.
NOTE 2 The scope of this document does not include the requirements for carrying out live working on electrical
power installations.
NOTE 3 The scope of this document considers safety requirements for HV installations and the influences of HV
installations on LV installations. For electrical installations up to 1 kV, IEC 60364 (all parts) applies.

  • Standard
    124 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    133 pages
    French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61936-1:2021/oprAA:2024(Amendment)
Power installations exceeding 1 kV AC and 1,5 kV DC - Part 1: AC
EN IEC 61936-1:2021/A11:2024

European common modification to EN 61936-1

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 19085-12:2025(Main)
Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-12:2024)
EN ISO 19085-12:2024

This document specifies the safety requirements and measures for manually loaded and unloaded
— single end tenoning machines with manual feed sliding table (defined in 3.1),
— single end tenoning machines with mechanical feed sliding table (defined in 3.2),
— single end tenoning and/or profiling machines with mechanical feed (defined in 3.3),
— double end tenoning and/or profiling machines with mechanical feed (defined in 3.4), also designed to be automatically loaded/unloaded,
— angular systems for tenoning and profiling with mechanical feed (defined in 3.5),
with maximum workpiece height capacity of 200 mm for single end machines and 500 mm for double end machines, capable of continuous production use, altogether referred to as “machines”.
It deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
The machines are designed to process in one pass one end or two sides, either opposite or perpendicular to each other, of workpieces made of:
1) solid wood;
2) materials with similar physical characteristics to wood (see ISO 19085 1:2021, 3.2);
3) fibre-cement, rock/glass wool, gypsum, plasterboard, only with machines with mechanical feed.
It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with:
— sanding units;
— fixed or movable workpiece support;
— automatic tool changing;
— automatic workpiece returner;
— glass bead saw unit;
— hinge recessing unit;
— post forming edge pre-cutting;
— boring unit;
— dynamic processing unit;
— sawing unit installed out of the integral enclosure, between machine halves in double end machines;
— foiling unit;
— coating unit;
— grooving unit with milling tool installed out of the integral enclosure, between machine halves;
— brushing unit;
— gluing unit;
— sealing unit;
— dowels inserting unit;
— tongues inserting unit;
— inkjet marking unit;
— laser marking unit;
— labelling unit;
— workpiece back-up device (anti-chipping / anti-splintering device);
— quick tool changing system.
This document does not deal with any hazards related to:
a) systems for automatic loading and unloading of the workpiece to a single machine other than automatic workpiece returner;
b) single machine being used in combination with any other machine (as part of a line);
c) use of tools, other than saw blades or milling tools for grooving, installed between machine halves and out of the integral enclosure in double end machines;
d) use of tools protruding out of the integral enclosure;
e) chemical characteristics of fibre-cement, rock/glass wool, gypsum, plasterboard and their dust.
It is not applicable to machines intended for use in potentially explosive atmosphere nor to machines manufactured prior to its publication.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13855:2025(Main)
Safety of machinery - Positioning of safeguards with respect to the approach of the human body (ISO 13855:2024)
EN ISO 13855:2024

This document specifies requirements for the positioning and dimensioning of safeguards with respect to the approach of the human body or its parts towards hazard(s) within the intended span-of-control as follows:
—     the position and dimension of the detection zone(s) of ESPE and pressure-sensitive mats and pressure-sensitive floors;
—     the position of two-hand control devices and single control devices;
—     the position of interlocking guards.
This document also specifies requirements for the positioning of safety-related manual control devices (SRMCD) with respect to the approach of the human body or its parts from within the safeguard space relative to:
—     the position and dimension of the detection zone(s) of ESPE and pressure-sensitive mats and pressure-sensitive floors; and
—     the position and dimension of interlocking guards.
When evaluating the ability of the human body or its parts to access SRMCD from within the intended safeguarded space, the requirements of this document are also applicable to determine the dimensions of safeguard(s). Approaches such as running, jumping or falling, are not considered in this document.
NOTE 1        The values for approach speeds (walking speed and upper limb movement) in this document are time tested and proven in practical experience.
NOTE 2        Other types of approach can result in approach speeds that are higher or lower than those defined in this document.
This document applies to safeguards used on machinery for the protection of persons 14 years and older.
Safeguards considered in this document include:
a)       electro-sensitive protective equipment (ESPE) such as:
—    active opto-electronic protective devices (AOPDs) (see IEC 61496-2);
—    AOPDs responsive to diffuse reflection that have one or more detection zone(s) specified in two dimensions (AOPDDRs-2D) (see IEC 61496-3);
—    AOPDs responsive to diffuse reflection that have one or more detection zone(s) specified in three dimensions (AOPDDRs-3D) (see IEC 61496-3);
—    vision based protective devices using reference pattern techniques (VBPDPP) (see IEC/TS 61496-4-2);
—    vision based protective devices using stereo vision techniques (VBPDST) (see IEC/TS 61496-4-3);
b)       pressure-sensitive mats and pressure-sensitive floors (see ISO 13856-1);
c)        two-hand control devices (see ISO 13851);
d)       single control devices;
e)       interlocking guards (see ISO 14120).
This document is not applicable to:
—     safeguards (e.g. pendant two-hand control devices) that can be manually moved, without using tools, nearer to the hazard zone than the separation distance;
—     protection against the risks from hazards arising from emissions (e.g. the ejection of solid or fluid materials, radiation, electric arcs, heat, noise, fumes, gases);
—     protection against the risks arising from failure of mechanical parts of the machine or gravity falls.
The separation distances derived from this document do not apply to safeguards used solely for presence sensing function.

  • Standard
    85 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1083-2:2025(Main)
Power-driven brushes - Part 2: Safety requirements
EN 1083-2:2024

This document specifies requirements and measures for removal or reduction of hazards resulting from the design and application of power-driven brushes.
NOTE   Power-driven brushing tools are e.g. cup brushes, wheel brushes, end brushes, disc brushes, tube brushes and head brushes.
This document also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
This document does not apply to cylinder brushes and strip brushes, brushes for car washing, vacuum cleaners, floor cleaning, drain and street cleaning machines and dental brushes.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1083-1:2025(Main)
Power-driven brushes - Part 1: Definitions and nomenclature
EN 1083-1:2024

This document defines terms which are used to describe power-driven brushes and strip brushes and describes the designation system.
This document does not cover brushes for car wash sites, vacuum cleaners, carpet cleaning machines, sewer and street cleaning machines, dental brushes, brushes for sealing and stripping.

  • Standard
    77 pages
    English language
    sale 10% off
    e-Library read for
    1 day