SIST EN 15651-3:2017
(Main)Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints
Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints
This European Standard specifies definitions and requirements for sealants used for sealing of joints applied in sanitary areas in the interior of buildings exposed to non-pressurized water.
It covers joints in:
- bathrooms;
- toilets;
- showers;
- domestic kitchens;
- prefabricated elements in sanitary areas (e.g. shower cubicles).
Industrial, drinking water, underwater (swimming pools, sewage systems, etc.), food contact applications and sealing of glass-ceramic cooktop panels (stove tops, ceramic hobs) are excluded from the scope.
This European Standard does not provide criteria or recommendations for the design of joints and installation of sealants in sanitary applications.
NOTE Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651-5.
This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in sanitary joints and to oil-based mastics.
Fugendichtstoffe für nicht tragende Anwendungen in Gebäuden und Fußgängerwegen - Teil 3: Dichtstoffe für Fugen im Sanitärbereich
Diese Europäische Norm legt Definitionen für und Anforderungen an Dichtstoffe zum Abdichten von Fugen im Sanitärbereich im Innern von Gebäuden fest, die keinem Druckwasser ausgesetzt sind.
Erfasst werden Fugen in:
- Badezimmern;
- Toiletten;
- Duschen;
- Küchen in Haushalte;
- vorgefertigen Elementen in Sanitärbereichen (z. B. Duschkabinen).
Anwendungen für Brauch- und Trinkwasser, Unterwasser-Anwendungen (Schwimmbäder, Abwassersysteme usw.), Anwendungen mit Nahrungsmittelkontakt und Fugen in Glaskeramikkochfeldern fallen nicht in den Anwendungsbereich dieser Norm.
Diese Europäische Norm legt keine Kriterien oder Empfehlungen für die Ausführung der Fugen und den Einbau der Fugendichtstoffe für Anwendungen im Sanitärbereich fest.
ANMERKUNG Festlegungen zur Bewertung und Überprüfung der Leistungsbeständigkeit - AVCP (d. h. zur Bestimmung des Produkttyps sowie zur werkseigenen Produktionskontrolle) und zur Kennzeichnung dieser Produkte werden in EN 15651-5 angegeben.
Diese Europäische Norm gilt weder für nicht plastische (nicht in pastöser Form vorliegende) Fugendichtstoffe für nicht tragende Anwendungen, noch für Fugendichtstoffe, die im Sanitärbereich angewendet werden, noch für Mastixharze auf Ölbasis.
Mastics pour joints pour des usages non structuraux dans les constructions immobilières et pour chemins piétonniers - Partie 3 : Mastics sanitaires
La présente Norme européenne spécifie les définitions et les exigences relatives aux mastics utilisés pour calfeutrer des joints exposés à une eau n'étant pas sous pression dans les zones sanitaires à l'intérieur des bâtiments.
Elle traite des joints dans :
- les salles de bain ;
- les toilettes ;
- les douches ;
- les cuisines domestiques ;
- les éléments préfabriqués dans les zones sanitaires (par exemple, cabines de douche).
Les applications industrielles liées à l'eau potable, sous l'eau (piscines, systèmes d'égout, etc.) ou impliquant un contact avec les aliments et le calfeutrement de surfaces de cuisson en vitrocéramique (tables de cuisson, plaque vitrocéramique) sont exclus du domaine d'application.
Cette Norme européenne ne fournit pas de critères ou de recommandations pour la conception des joints et la mise en oeuvre des mastics dans les applications sanitaires.
NOTE Les dispositions concernant l'évaluation et la vérification de la constance des performances, ou EVCP, (à savoir la détermination du type de produit et le contrôle de la production en usine) et le marquage de ces produits sont données dans l'EN 15651-5.
La présente Norme européenne ne s'applique pas aux produits pour joints non structuraux sous une autre forme que pâteuse utilisés dans les joints sanitaires, ni aux mastics à base d'huile.
Tesnilne mase za nekonstrukcijske stike v stavbah in na površinah za pešce - 3. del: Tesnilne mase za stike v sanitarijah
Ta evropski standard določa definicije in zahteve za tesnilne mase, ki se uporabljajo za tesnjenje stikov na sanitarnih območjih znotraj stavb, ki so izpostavljena vodi, ki ni pod tlakom.
Zajema stike v:
– kopalnicah;
– straniščih;
– tuš kabinah;
– domačih kuhinjah;
– montažnih elementih na sanitarnih površinah (npr. tuš kabine).
Industrijska uporaba, uporaba s pitno vodo, podvodna uporaba (bazeni, kanalizacija itd.), uporaba s hrano in tesnjenje steklo-keramičnih kuhalnih plošč (štedilniki, keramične kuhalne plošče) ne spadajo na področje uporabe tega standarda.
Ta evropski standard ne podaja meril ali priporočil za projektiranje stikov in nameščanje tesnilnih mas pri sanitarni uporabi.
OPOMBA Določila o ocenjevanju in preverjanju stalnosti delovanja – AVCP (tj. določevanje tipa izdelka in kontrola proizvodnje v obratu) ter označevanju teh izdelkov so podana v standardu EN 15651-5.
Ta evropski standard se ne uporablja za nekonstrukcijske tesnilne mase, ki niso v obliki paste, tesnilne mase, ki se uporabljajo v sanitarnih stikih, ter kite na osnovi olja.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tesnilne mase za nekonstrukcijske stike v stavbah in na površinah za pešce - 3. del: Tesnilne mase za stike v sanitarijahFugendichtstoffe für nicht tragende Anwendungen in Gebäuden und Fußgängerwegen - Teil 3: Dichtstoffe für Fugen im SanitärbereichMastics pour joints pour des usages non structuraux dans les constructions immobilières et pour chemins piétonniers - Partie 3 : Mastics sanitairesSealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints91.140.70Sanitarne napraveSanitary installations91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 15651-3:2017SIST EN 15651-3:2017en,fr,de01-april-2017SIST EN 15651-3:2017SLOVENSKI
STANDARDSIST EN 15651-3:20131DGRPHãþD
SIST EN 15651-3:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15651-3
February
t r s y ICS
{ sä s r rä w r Supersedes EN
s w x w sæ uã t r s tEnglish Version
Sealants for nonæstructural use in joints in buildings and pedestrian walkways æ Part
uã Sealants for sanitary jointsMastics pour joints pour des usages non structuraux dans les constructions immobilières et pour chemins piétonniers æ Partie
u ã Mastics sanitaires
Fugendichtstoffe für nicht tragende Anwendungen in Gebäuden und Fußgängerwegen æ Teil
uã Dichtstoffe für Fugen im Sanitärbereich This European Standard was approved by CEN on
t w December
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s w x w sæ uã t r s y ESIST EN 15651-3:2017
EN 15651-3:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Requirements . 6 4.1 Identification requirements and test methods . 6 4.1.1 Short description of the sealant . 6 4.1.2 Thermogravimetric test. 6 4.1.3 Density . 6 4.1.4 Indentation hardness (Shore hardness) . 6 4.2 Conditioning, test procedure and substrates . 6 4.3 Performance requirements and test methods for non-structural sealants for sanitary joints . 7 4.3.1 General . 7 4.3.2 Resistance to flow . 8 4.3.3 Evaluation of the action of microorganisms . 8 4.4 Release of dangerous substances . 9 4.5 Reaction to fire . 9 4.5.1 General . 9 4.5.2 Mounting and fixing conditions for test samples . 9 5 Durability . 11 6 Sampling . 11 7 Assessment and verification of constancy of performance . 11 7.1 General . 11 7.2 Product type determination . 11 7.3 Factory production control . 11 8 Marking and labelling . 11 Annex A (informative)
Example on the frequency of tests for factory production control . 12 Annex ZA (informative)
Relationship of this European Standard with Regulation (EU) No.305/2011 . 13 ZA.1 Scope and relevant characteristics . 13 ZA.2 System of Assessment and Verification of Constancy of Performance (AVCP) . 14 ZA.3 Assignment of AVCP tasks . 14 Bibliography . 17
SIST EN 15651-3:2017
EN 15651-3:2017 (E) 3 European foreword This document (EN 15651-3:2017) has been prepared by Technical Committee CEN/TC 349 “Sealants for joints in building constuction”, the secretariat of which is held by AFNOR. This document supersedes EN 15651-3:2012. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2017, and conflicting national standards shall be withdrawn at the latest by November 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports basic work requirements of EU Regulation. For relationship with EU Regulation, see informative Annex ZA, which is an integral part of this document. This document is one of the product European Standards within the framework series of EN 15651 on Sealants for non-structural use in joints in buildings and pedestrian walkways, as follows: — Part 1: Sealants for facade elements, — Part 2: Sealants for glazing, — Part 3: Sealants for sanitary joints (this document), — Part 4: Sealants for pedestrian walkways, — Part 5: Assessment and verification of constancy of performance, marking and labelling. The following significant technical changes have been implemented in this new edition: — Clause 4.1.3 and Clause 5 have been improved; — Clause 4.5 has been modified; — Clause 7 and Annex ZA have been changed in accordance with the regulation (EU) No.305/2011. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 15651-3:2017
EN 15651-3:2017 (E) 4 1 Scope This European Standard specifies definitions and requirements for sealants used for sealing of joints applied in sanitary areas in the interior of buildings exposed to non-pressurized water. It covers joints in: — bathrooms; — toilets; — showers; — domestic kitchens; — prefabricated elements in sanitary areas (e.g. shower cubicles). Industrial, drinking water, underwater (swimming pools, sewage systems, etc.), food contact applications and sealing of glass-ceramic cooktop panels (stove tops, ceramic hobs) are excluded from the scope. This European Standard does not provide criteria or recommendations for the design of joints and installation of sealants in sanitary applications. NOTE Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651–5. This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in sanitary joints and to oil-based mastics. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13238, Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using data from reaction to fire tests EN 15651-5:2017, Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 5: Evaluation of conformity and marking EN ISO 846:1997, Plastics - Evaluation of the action of microorganisms (ISO 846:1997) EN ISO 868, Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868) EN ISO 2811-1:2016, Paints and varnishes - Determination of density - Part 1: Pycnometer method (ISO 2811-1:2016) EN ISO 6927, Buildings and civil engineering works - Sealants - Vocabulary (ISO 6927) EN ISO 7390, Building construction - Jointing products - Determination of resistance to flow of sealants (ISO 7390) SIST EN 15651-3:2017
EN 15651-3:2017 (E) 5 EN ISO 8340, Building construction - Sealants - Determination of tensile properties at maintained extension (ISO 8340) EN ISO 9047, Building construction - Jointing products - Determination of adhesion/cohesion properties of sealants at variable temperatures (ISO 9047) EN ISO 10563, Building construction - Sealants - Determination of change in mass and volume (ISO 10563) EN ISO 10590, Building construction - Sealants - Determination of tensile properties of sealants at maintained extension after immersion in water (ISO 10590) EN ISO 10591, Building construction - Sealants - Determination of adhesion/cohesion properties of sealants after immersion in water (ISO 10591) EN ISO 11358 (all parts), Plastics — Thermogravimetry (TG) of polymers — General principles (ISO 11358) EN ISO 11600:2003, Building construction - Jointing products - Classification and requirements for sealants (ISO 11600:2002) EN ISO 11925-2, Reaction to fire tests - Ignitability of products subjected to direct impingement of flame - Part 2: Single-flame source test (ISO 11925-2) ISO 13640, Building construction — Jointing products — Specifications for test substrates 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 6927 and the following apply. 3.1 non-reactive sealant mainly physical drying mechanism, without significant change in the molecular weight of the main polymer 3.2 reactive sealant mainly curing by chemical reaction, with significant increase of the molecular weight of the main polymer 3.3 cure irreversible transformation of a sealant from a liquid or paste-like state into a hardened or rubber-like solid state 3.4 uncured / wet state of a sealant prior to the above transformation SIST EN 15651-3:2017
EN 15651-3:2017 (E) 6 4 Requirements 4.1 Identification requirements and test methods 4.1.1 Short description of the sealant The short description of the non-structural sealant for sanitary joints includes: brand name, type (general chemical family), opaque or translucent, waterborne or solvent based or solvent free, reactive or non-reactive, and one or multi-component (e.g. waterborne acrylic opaque and one component, etc.). The primer shall be stated for the substrate concerned, if relevant (name, chemical type, etc.). 4.1.2 Thermogravimetric test The test shall be carried out in accordance with EN ISO 11358 on the uncured or wet sealant, between 35 °C and 900 °C, temperature slope 10 °C/min, non-oxidative condition (e.g. nitrogen). A single sample shall be used for this test. A single specimen may be tested and there shall be no significant difference between the reference curve and derivative (profile). In the case of a multi-component sealant, each component shall be evaluated (if relevant). 4.1.3 Density 4.1.3.1 Principal A pyknometer is filled with the product under test. The density is calculated from the mass of the product in the pyknometer and the known volume of the pyknometer. 4.1.3.2 Method A test temperature of (23,0 ± 0,5) °C shall be used and the test sample and pyknometer shall be conditioned to this temperature, and it shall be ensured that the temperature variation does not exceed 0,5 °C during testing. The determination of the density shall be in accordance with EN ISO 2811-1:2016 using a suitable 50 cm3 calibrated pyknometer as described in EN ISO 2811-1:2016, 6.1.1. An alternative is the 50 cm3 Hubbard pyknometer as described in ISO 3507. Measurements should be carried out on the uncured or wet sealant and in the case of a multi-component sealant, each component shall be evaluated. At least three samples shall be tested. The specific pyknometer used and the mean value, recorded to two decimal places, shall be declared. The tolerance of the declared values shall be within ± 5 %. 4.1.4 Indentation hardness (Shore hardness) The determination of the indentation hardness shall be in accordance with EN ISO 868. The test shall be performed on the cured or dried sealant. The exact conditions of the test shall be defined by the manufacturer, i.e. thickness, cure/drying times and temperature and relative humidity, specific Shore type (A, D…), test time, temperature, etc. At least three samples shall be tested and five measurements taken per sample. The mean value and tolerances of all measurements, recorded to the nearest unit, shall be declared. 4.2 Conditioning, test procedure and substrates When determining the classification of a sanitary sealant according to the requirements of this standard, the same conditioning procedure shall be used in all the relevant test methods (Method A or Method B conditioning shall be used for all relevant tests). SIST EN 15651-3:2017
EN 15651-3
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tesnilne mase za nekonstrukcijske stike v stavbah in na površinah za pešce - 3. del: Tesnilne mase za stike v sanitarijahFugendichtstoffe für nicht tragende Anwendungen in Gebäuden und Fußgängerwegen - Teil 3: Dichtstoffe für Fugen im SanitärbereichMastics pour joints pour des usages non structuraux dans les constructions immobilières et pour chemins piétonniers - Partie 3 : Mastics sanitairesSealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints91.140.70Sanitarne napraveSanitary installations91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:FprEN 15651-3kSIST FprEN 15651-3:2016en,fr,de01-november-2016kSIST FprEN 15651-3:2016SLOVENSKI
STANDARD
kSIST FprEN 15651-3:2016
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 15651-3
September
t r s x ICS
{ sä s r rä w r Will supersede EN
s w x w sæ uã t r s tEnglish Version
Sealants for nonæstructural use in joints in buildings and pedestrian walkways æ Part
uã Sealants for sanitary jointsMastics pour joints pour des usages non structuraux dans les constructions immobilières et pour chemins piétonniers æ Partie
u ã Mastics sanitaires
Fugendichtstoffe für nicht tragende Anwendungen in Gebäuden und Fußgängerwegen æ Teil
uã Dichtstoffe für Fugen im Sanitärbereich This draft European Standard is submitted to CEN members for unique acceptance procedureä It has been drawn up by the
If this draft becomes a European Standardá CEN members are bounwhich stipulate the conditions for giving this European Standard the status of a national standard without any alterationä
This draft European Standard was established by CEN in three ofer language made by translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
Recipients of this draft are invited to submitá with their commentsá notification of any relevant patent rights of which they are aware and to provide supporting documentationä
Warning ã This document is not a European Standardä It is distributed for review and commentsä It is subject to change without notice and shall not be referred to as a European Standardä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä FprEN
s w x w sæ uã t r s x EkSIST FprEN 15651-3:2016
FprEN 15651-3:2016 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Requirements . 6 4.1 Identification requirements and test methods . 6 4.1.1 Short description of the sealant . 6 4.1.2 Thermogravimetric test. 6 4.1.3 4.1.3 Density . 6 4.1.4 4.1.4 Indentation hardness (Shore hardness) . 6 4.2 Conditioning, test procedure and substrates . 6 4.3 Performance requirements and test methods for non-structural sealants for sanitary joints . 7 4.3.1 General . 7 4.3.2 Resistance to flow . 8 4.3.3 Evaluation of the action of microorganisms . 8 4.4 Release of dangerous substances . 9 4.5 Reaction to fire . 9 4.5.1 General . 9 4.5.2 Mounting and fixing conditions for test samples . 9 5 Durability . 11 6 Sampling . 11 7 Assessment and verification of constancy of performance . 11 7.1 General . 11 7.2 Product type determination . 11 7.3 Factory production control . 11 8 Marking and labelling . 11 Annex A (informative)
Example on the frequency of tests for factory production control . 12 Annex ZA (informative)
Relationship of this European Standard with Regulation (EU) No.305/2011 . 13 ZA.1 ZA.1 Scope and relevant characteristics . 13 ZA.2 ZA.2 System of Assessment and Verification of Constancy of Performance (AVCP) . 14 ZA.3 ZA.3 Assignment of AVCP tasks . 14 Bibliography . 17
kSIST FprEN 15651-3:2016
FprEN 15651-3:2016 (E) 3 European foreword This document (FprEN 15651-3:2016) has been prepared by Technical Committee CEN/TC 349 “Sealants for joints in building constuction”, the secretariat of which is held by AFNOR. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 15651-3:2012. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports basic work requirements of EU Regulation. For relationship with EU Regulation, see informative Annex ZA, which is an integral part of this document. This document is one of the product European Standards within the framework series of EN 15651 on Sealants for non-structural use in joints in buildings and pedestrian walkways, as follows: — Part 1: Sealants for facade elements, — Part 2: Sealants for glazing, — Part 3: Sealants for sanitary joints (this document), — Part 4: Sealants for pedestrian walkways, — Part 5: Assessment and verification of constancy of performance, marking and labelling. The following significant technical changes have been implemented in this new edition: — Clause 4.1.3 and Clause 5 have been improved; — Clause 7 and Annex ZA have been changed in accordance with the regulation (EU) No.305/2011. kSIST FprEN 15651-3:2016
FprEN 15651-3:2016 (E) 4 1 Scope This European Standard specifies definitions and requirements for sealants used for sealing of joints applied in sanitary areas in the interior of buildings exposed to non-pressurized water. It covers joints in: — bathrooms; — toilets; — showers; — domestic kitchens; — prefabricated elements in sanitary areas (e.g. shower cubicles). Industrial, drinking water, underwater (swimming pools, sewage systems, etc.), food contact applications and sealing of glass-ceramic cooktop panels (stove tops, ceramic hobs) are excluded from the scope. This European Standard does not provide criteria or recommendations for the design of joints and installation of sealants in sanitary applications. NOTE Provisions on assessment and verification of constancy of performance - AVCP (i.e. Product type determination and Factory Production Control) and marking of these products are given in EN 15651–5. This European Standard does not apply to non-structural sealants in any of non-paste form, to those used in sanitary joints and to oil-based mastics. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13238, Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using data from reaction to fire tests FprEN 15651-5:2016, Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 5: Evaluation of conformity and marking EN ISO 846:1997, Plastics - Evaluation of the action of microorganisms (ISO 846:1997) EN ISO 868, Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868) EN ISO 2811-1:2016, Paints and varnishes - Determination of density - Part 1: Pyknometer method (ISO 2811-1:2016) EN ISO 6927, Buildings and civil engineering works - Sealants - Vocabulary (ISO 6927) EN ISO 7390, Building construction - Jointing products - Determination of resistance to flow of sealants (ISO 7390) kSIST FprEN 15651-3:2016
FprEN 15651-3:2016 (E) 5 EN ISO 8340, Building construction - Sealants - Determination of tensile properties at maintained extension (ISO 8340) EN ISO 9047, Building construction - Jointing products - Determination of adhesion/cohesion properties of sealants at variable temperatures (ISO 9047) EN ISO 10563, Building construction - Sealants - Determination of change in mass and volume (ISO 10563) EN ISO 10590, Building construction - Sealants - Determination of tensile properties of sealants at maintained extension after immersion in water (ISO 10590) EN ISO 10591, Building construction - Sealants - Determination of adhesion/cohesion properties of sealants after immersion in water (ISO 10591) EN ISO 11358 (all parts), Plastics — Thermogravimetry (TG) of polymers — General principles (ISO 11358) EN ISO 11600:2003, Building construction - Jointing products - Classification and requirements for sealants (ISO 11600:2002) EN ISO 11925-2, Reaction to fire tests - Ignitability of products subjected to direct impingement of flame - Part 2: Single-flame source test (ISO 11925-2) ISO 13640, Building construction — Jointing products — Specifications for test substrates 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 6927 and the following apply. 3.1 non-reactive sealant mainly physical drying mechanism, without significant change in the molecular weight of the main polymer 3.2 reactive sealant mainly curing by chemical reaction, with significant increase of the molecular weight of the main polymer 3.3 cure irreversible transformation of a sealant from a liquid or paste-like state into a hardened or rubber-like solid state 3.4 uncured / wet state of a sealant prior to the above transformation kSIST FprEN 15651-3:2016
FprEN 15651-3:2016 (E) 6 4 Requirements 4.1 Identification requirements and test methods 4.1.1 Short description of the sealant The short description of the non-structural sealant for sanitary joints includes: brand name, type (general chemical family), opaque or translucent, waterborne or solvent based or solvent free, reactive or non-reactive, and one or multi-component (e.g. waterborne acrylic opaque and one component, etc.). The primer shall be stated for the substrate concerned, if relevant (name, chemical type, etc.). 4.1.2 Thermogravimetric test The test shall be carried out in accordance with EN ISO 11358 on the uncured or wet sealant, between 35 °C and 900 °C, temperature slope 10 °C/min, non-oxidative condition (e.g. nitrogen). A single sample shall be used for this test. A single specimen may be tested and there shall be no significant difference between the reference curve and derivative (profile). In the case of a multi-component sealant, each component shall be evaluated (if relevant). 4.1.3 Density 4.1.3.1 Principal A pyknometer is filled with the product under test. The density is calculated from the mass of the product in the pyknometer and the known volume of the pyknometer. 4.1.3.2 Method A test temperature of (23,0 ± 0,5) °C shall be used and the test sample and pyknometer shall be conditioned to this temperature, and it shall be ensured that the temperature variation does not exceed 0,5 °C during testing. The determination of the density shall be in accordance with EN ISO 2811-1:2016 using a suitable 50 cm3 calibrated pyknometer as described in EN ISO 2811-1:2016, 6.1.1. An alternative is the 50 cm3 Hubbard pyknometer as described in ISO 3507. Measurements should be carried out on the uncured or wet sealant and in the case of a multi-component sealant, each component shall be evaluated. At least three samples shall be tested. The specific pyknometer used and the mean value, recorded to two decimal places, shall be declared. The tolerance of the declared values shall be within ± 5 %. 4.1.4 Indentation hardness (Shore hardness) The determination of the indentation hardness shall be in accordance with EN ISO 868. The test shall be performed on the cured or dried sealant. The exact conditions of the test shall be defined by the manufacturer, i.e. thickness, cure/drying times and temperature and relative humidity, specific Shore type (A, D…), test time, temperature, etc. At least three samples shall be tested and five measurements taken per sample. The mean value and tolerances of all measurements, recorded to the nearest unit, shall be declared. 4.2 Conditioning, test procedure and substrates When determining the classification of a sanitary sealant according to the requirements of this standard, the same conditioning procedure shall be used in all the relevant test methods (Method A or Method B conditioning shall be used for all relevant tests). kSIST FprEN 15651-3:2016
FprEN 15651-3:2016 (E) 7 For each test method, three test specimens for each substrate shall be tested. The same batch of sealant (and primer, if used) shall be used in all tests. The same substrates (material and surface finish) shall be used in all tests. Substrates to be used in all mechanical tests concerned shall be glass and/or anodised a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.