iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12573-1:2001

(Main)

Welded static non-pressurized thermoplastic tanks - Part 1: General principles

Welded static non-pressurized thermoplastic tanks - Part 1: General principles

This standard specifies general principles for welded static non-pressurised thermoplastic tanks. It applies to work shop and site fabrications. The standard covers tanks with a capacity of 0,45 m3 (450 litres) and above. Tanks which comply with the requirements of this standard are not intended to withstand internal pressure or vaccuum other than that which may occur during the transfer of fluids (including gases) in their normal operation.

Geschweißte ortsfeste drucklose Behälter (Tanks) aus Thermoplasten - Teil 1: Allgemeine Grundsätze

Diese Norm stellt allgemeine Grundsätze für geschweißte ortsfeste drucklose Tanks aus Thermoplasten auf. Sie gilt für die Werksfertigung und die Standort- fertigung. Diese Norm gilt für Tanks mit einem Volumen von > oder = 0,45 m3 (450 Liter). Diese Norm ist nur anwendbar für Tanks, die ohne inneren Überdruck oder Vakuum betrieben werden, ausgenommen die während des Befüllens/Entleerens mit Fluiden (einschließlich Gasen) bei Normalbetrieb vorkommenden Drücke.

Cuves statiques soudées en matieres thermoplastiques sans pression - Partie 1: Principes généraux

La présente norme prescrit les principes généraux applicables aux cuves statiques soudées en matieres thermoplastiques sans pression. Elle s'applique aux constructions effectuées en atelier et sur site. La présente norme s'applique aux cuves dont la capacité est supérieure ou égale a 0,45 m3 (450 litres). Les cuves conformes aux prescriptions de la présente norme ne sont pas prévues pour supporter une surpression ou une dépression autres que celles qui peuvent se produire durant le transfert des fluides (y compris les gaz) au cours de leur utilisation normale.

Welded static non-pressurized thermoplastic tanks - Part 1: General principles

General Information

Status
Published
Publication Date
31-May-2001
ICS
23.020.10 - Stationary containers and tanks
Technical Committee
SS SPL - Technical Board for the general field
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jun-2001
Due Date
01-Jun-2001
Completion Date
01-Jun-2001
Ref Project
EN 12573-1:2000 - Welded static non-pressurized thermoplastic tanks - Part 1: General principles

Buy Standard

EN 12573-1:2001EN 12573-1:2001
PreviousNext
Standard
EN 12573-1:2001
English language
25 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Welded static non-pressurized thermoplastic tanks - Part 1: General principlesGeschweißte ortsfeste drucklose Behälter (Tanks) aus Thermoplasten - Teil 1: Allgemeine GrundsätzeCuves statiques soudées en matieres thermoplastiques sans pression - Partie 1: Principes générauxWelded static non-pressurized thermoplastic tanks - Part 1: General principles23.020.10UH]HUYRDUMLStationary containers and tanksICS:Ta slovenski standard je istoveten z:EN 12573-1:2000SIST EN 12573-1:2001en01-junij-2001SIST EN 12573-1:2001SLOVENSKI
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12573-3:2000(Main)
Welded static non-pressurized thermoplastic tanks - Part 3: Design and calculation for single skin rectangular tanks
EN 12573-3:2000

This standard specifies the design and calculation for single sking rectangular tanks, fabricated from the following thermoplastics: Polyethylene (PE), Polypropylene (PP), Poly (vinyl chloride) (PVC), Poly (vinylidene fluoride) (PVDF). The tanks may be strengthened on the outside by means of ribs or frames made of the same or other materials. This standard is only applicable to tanks which are not intended to withstand internal pressure or vaccuum, other than that which may occur during the transfer of fluids (including gases) in their normal operation.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12573-4:2000(Main)
Welded static non-pressurised thermoplastic tanks - Part 4: Design and calculation of flanged joints
EN 12573-4:2000

This part of this standard specifies the design and calculation of circular flanged joints, fabricated in the following thermoplastics: Polyethylene (PE), Polypropylene (PP), Poly (vinyl chloride) (PVC), Ply (vinylidene fluoride) (PVDF)

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12573-2:2000(Main)
Welded static non-pressurised thermoplastic tanks - Part 2: Calculation of vertical cylindrical tanks
EN 12573-2:2000

This standard establishes rules for the design and calculation of welded static,vertical, non-pressurised, cylindrical, flat-bottom thermoplastic tanks. This standard applies to tanks fabricated in the following thermoplastics: Polyethylene (PE), Polypropylene (PP), Poly (vinyl chloride) (PVC), Poly (vinylidene fluoride) (PVDF). This standard does not take into account wind and/or snow loading. If wind or/and snow loading has to be taken into account additional calculations are necessary.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28765:2023(Main)
Vitreous and porcelain enamels - Design of bolted steel tanks for the storage or treatment of water or municipal or industrial effluents and sludges (ISO 28765:2022)
EN ISO 28765:2022

This document specifies the requirements for the design and use of vitreous enamel coated bolted
cylindrical steel tanks for the storage or treatment of water or municipal or industrial effluents and
sludges.
It is applicable to the design of the tank and any associated roof and gives guidance on the requirements
for the design of the foundation.
It is applicable where:
a) the tank is cylindrical and is mounted on a load-bearing base substantially at or above ground level;
b) the product of the tank diameter in metres and the wall height in metres lies within the range
5 to 500;
c) the tank diameter does not exceed 100 m and the total wall height does not exceed 50 m;
d) the stored material has the characteristics of a liquid, exerting a negligible frictional force on the
tank wall; the stored material can be undergoing treatment as part of a municipal or industrial
effluent treatment process;
e) the internal pressure in the headspace above the liquid does not exceed 50 kPa and the internal
partial vacuum above the liquid does not exceed 10 kPa;
f) the walls of the tank are vertical;
g) the floor of the tank is substantially flat at its intersection with the wall; the floor of the tank can
have a rise or fall built in to allow complete emptying of the tank contents, the slope of which does
not exceed 1:100;
h) there is negligible inertial and impact load due to tank filling;
i) the minimum thickness of the tank shell is 1,5 mm;
j) the material used for the manufacture of the steel sheets is carbon steel (tanks constructed of
sheets made from aluminium or stainless steel are outside the scope of this document);
k) the temperature of the tank wall during operation is within the range −50 °C to +100 °C under all
operating conditions.
This document also gives details of procedures to be followed during installation on site and for
inspection and maintenance of the installed tank.
It does not apply to chemical-reaction vessels.
It does not cover resistance to fire.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15969-2:2022(Main)
Tanks for transport of dangerous goods - Digital interface for the data transfer between tank vehicle and with stationary facilities - Part 2: Commercial and logistic data
EN 15969-2:2022

This European Standard specifies the data structure needed for tour management, scheduling orders of measured and unmeasured products online to the truck. Processed orders are transferred back to the host in the office at once or later every time the truck is online.
It specifies the transfer of commercial and logistic data between transport vehicle equipment, on board computer of the tank vehicle and stationary facilities for all communication channels between these parties.
This document should only be used in conjunction with EN 15969-1 and should not modify or override any of the requirements of EN 15969-1.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15969-1:2022(Main)
Tanks for transport of dangerous goods - Digital interface for the data transfer between tank vehicle and with stationary facilities - Part 1: Protocol specification - Control, measurement and event data
EN 15969-1:2022

This document specifies data protocols and data format for the communication between electronic
equipment (TVE), on-board computer (OBC) of the tank vehicle and stationary equipment.
This document specifies the basic protocol FTL used in the communication (basic protocol layer), the
format and structure of FTL-data to be transmitted (data protocol layer) and describes the content of the
FTL-data.
This data protocol can be used for other application e.g. between stationary tank equipment and offices.

  • Standard
    114 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    116 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13799:2022(Main)
LPG equipment and accessories - Contents gauges for Liquefied Petroleum Gas (LPG) pressure vessels
EN 13799:2022

This European Standard specifies minimum requirements for design and testing of contents gauges, which are directly connected to transportable tanks, drums, cylinders and static LPG tanks above 0,5 l water capacity excluding those used for automotive containers. This European Standard does not apply to refineries or other process plants.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13121-1:2021(Main)
GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance criteria
EN 13121-1:2021

This document gives requirements for specification and acceptance conditions of raw materials for GRP tanks and vessels with or without lining for storage or processing of fluids, factory made or site built, non-pressurised or pressurised, for use above ground.
Tanks and vessels for storage or processing of food, raw materials for food and potable water additionally have to be in compliance with relevant EU directives and applicable national standards and regulations.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12542:2020(Main)
LPG equipment and accessories - Static welded steel cylindrical tanks, serially produced for the storage of Liquefied Petroleum Gas (LPG) having a volume not greater than 13 m³ - Design and manufacture
EN 12542:2020

This European Standard specifies requirements for the design and manufacture of static welded steel cylindrical tanks, serially produced for the storage of liquefied petroleum gas (LPG) with a volume not greater than 13 m³ and for installation above or below ground.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12285-3:2019(Main)
Workshop fabricated steel tanks - Part 3: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids for heating and cooling of buildings
EN 12285-3:2019

This document specifies the product characteristics and test/assessment methods for workshop
fabricated cylindrical, horizontal steel tanks, single (type S) and double skin (type D) intended to be
used for the underground storage of water polluting liquids (both flammable and non-flammable),
specifically used for storage and/or supply of fuel for building heating/cooling systems, and of hot or
cold water not intended for human consumption at normal ambient temperature conditions (−20 °C to
+50 °C) within the following limits:
— from 800 mm up to 3000 mm nominal diameter and;
— up to a maximum overall length of 6 times the nominal diameter;
— for liquids with a maximum density of up to 1,1 kg/l and;
— with an operating pressure (Po) of maximum 50 kPa (0,5 bar(g)) and minimum – 5 kPa (–50
mbar(g)) and;
— for double skin tanks with a vacuum leak detection system where the kinematic viscosity does not
exceed 5 × 10−3 m2/s.
Two tank types are distinguished:
— Type S: Single skin;
— Type D: Double skin.
Tanks designed to this document allow for an earth cover of up to 1,5 m. If there are imposed traffic
loads or a greater earth cover, calculation will occur.
This document is not applicable to tanks installed in industrial processes or in petrol stations, nor to
loads and special measures necessary in areas subject to risk of earthquakes and/or to flooding.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day