SIST EN 12413:2007/kprA1:2010
(Amendment)Safety requirements for bonded abrasive products
Safety requirements for bonded abrasive products
Amendment:
During revision of EN 12413:1999 an editorial simplification of the table with the scope of inspection (EN 12413:1999, Table 14) had been decided (see meeting report, document CEN/TC 143/WG 2 N 132). However this simplification led to a tightening of the scope of inspection for "all other abrasive products" in EN 12413:2007, Table 7 which was not covered by the compilation of comments table (document CEN/TC 143/WG 2 N 133) and no technical reason can be seen for this tightening of requirements.
Scope of EN 12413:2007:
This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products.
This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer.
The hazards taken into consideration are listed in Clause 4 of this standard.
This standard does not apply to superabrasives and coated abrasive products.
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel
Exigences de sécurité pour les produits abrasifs agglomérés
Varnostne zahteve za vezana brusilna sredstva
General Information
Relations
Overview
SIST EN 12413:2007/kprA1:2010 is an important European standard developed by CEN that specifies safety requirements for bonded abrasive products. This amendment focuses on clarifying and adjusting the scope of inspection for various abrasive products, ensuring enhanced safety protocols without imposing unnecessary tightening of requirements. The standard is applicable specifically to rotating bonded abrasive products, addressing hazards related to their design and usage.
This document builds on the previous EN 12413:1999 and EN 12413:2007 editions by refining inspection scopes and test procedures. It is crucial for manufacturers, safety regulators, and users aiming to comply with safety norms and optimize the risk management of abrasive tools in industrial settings.
Key Topics
Scope of Application
Applicable exclusively to rotating bonded abrasive products, SIST EN 12413:2007/kprA1:2010 excludes superabrasives and coated abrasive products. It defines safety requirements to reduce hazards arising from product design and operational use.Hazard Considerations
The standard takes account of physical and mechanical risks such as breaking, fragmentation, and release of abrasive material during high-speed rotation, which can cause injury or equipment damage.Inspection and Testing Protocols
The amendment revises Table 7 of the original EN 12413:2007 standard, specifying the minimum scope of inspection based on product diameter and other parameters such as bond type and abrasive size. Inspection scope varies to ensure critical product categories receive 100% inspection, while others may require statistically valid samples.Safety Information and Compliance Verification
EN 12413 mandates manufacturers to provide clear safety information for users and establish procedures confirming compliance through tests like burst testing, dimensional checks, and material stability assessments.Editorial Clarifications
The amendment addresses editorial simplifications that inadvertently tightened inspection requirements without technical justification, ensuring a practical and balanced approach to safety testing.
Applications
Manufacturing of Abrasive Tools
Producers of grinding wheels, cutting discs, and other bonded abrasive products use this standard to design, manufacture, and test products that meet European safety regulations, minimizing potential injuries from product failure.Quality Control and Inspection
Quality assurance teams apply SIST EN 12413:2007/kprA1:2010 criteria during batch inspections and product certification to ensure safety requirements are met before products enter the market.Industrial Safety Management
Safety officers and supervisors implement this standard’s guidance to establish safe operational procedures, ensuring familiarity with product limitations and protective measures during abrasive tool use.Regulatory Compliance
Enforcement authorities and certification bodies reference this standard when conducting audits or certifying abrasive products for the EU market, helping harmonize safety practices across member states.
Related Standards
EN 12413:1999 - The base version of the safety requirements for bonded abrasives, providing the original framework and inspection scope.
EN 12413:2007 - The revised edition including editorial updates and changes in inspection tables that prompted this amendment.
ISO 603:2014 - Safety specifications for bonded abrasive products, often aligned with EN standards for global consistency.
EN 13236 - Safety requirements for superabrasives such as diamond and cubic boron nitride wheels, excluded from EN 12413’s scope.
EN 1087-1 - Standards covering coated abrasive products, delineating safety and performance outside the bonded abrasives scope.
Keywords: EN 12413:2007 amendment, bonded abrasive products safety, abrasive product inspection, rotating abrasive tools, grinding wheel safety, abrasive tools certification, European abrasive product standards, CEN abrasive safety requirements, abrasive product hazard reduction, bonded abrasives testing procedures.
Frequently Asked Questions
SIST EN 12413:2007/kprA1:2010 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Safety requirements for bonded abrasive products". This standard covers: Amendment: During revision of EN 12413:1999 an editorial simplification of the table with the scope of inspection (EN 12413:1999, Table 14) had been decided (see meeting report, document CEN/TC 143/WG 2 N 132). However this simplification led to a tightening of the scope of inspection for "all other abrasive products" in EN 12413:2007, Table 7 which was not covered by the compilation of comments table (document CEN/TC 143/WG 2 N 133) and no technical reason can be seen for this tightening of requirements. Scope of EN 12413:2007: This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products. This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer. The hazards taken into consideration are listed in Clause 4 of this standard. This standard does not apply to superabrasives and coated abrasive products.
Amendment: During revision of EN 12413:1999 an editorial simplification of the table with the scope of inspection (EN 12413:1999, Table 14) had been decided (see meeting report, document CEN/TC 143/WG 2 N 132). However this simplification led to a tightening of the scope of inspection for "all other abrasive products" in EN 12413:2007, Table 7 which was not covered by the compilation of comments table (document CEN/TC 143/WG 2 N 133) and no technical reason can be seen for this tightening of requirements. Scope of EN 12413:2007: This standard is applicable to rotating bonded abrasive products. It specifies requirements and/or measures for the removal or reduction of hazards resulting from the design and application of the abrasive products. This standard also contains procedures and tests for verification of compliance with the requirements as well as safety information for use, which is to be made available to the user by the manufacturer. The hazards taken into consideration are listed in Clause 4 of this standard. This standard does not apply to superabrasives and coated abrasive products.
SIST EN 12413:2007/kprA1:2010 is classified under the following ICS (International Classification for Standards) categories: 25.100.70 - Abrasives. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 12413:2007/kprA1:2010 has the following relationships with other standards: It is inter standard links to SIST EN 12413:2007+A1:2011, SIST EN 12413:2007. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
You can purchase SIST EN 12413:2007/kprA1:2010 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2010
Varnostne zahteve za vezana brusilna sredstva
Safety requirements for bonded abrasive products
Sicherheitsanforderungen für Schleifkörper aus gebundenem Schleifmittel
Exigences de sécurité pour les produits abrasifs agglomérés
Ta slovenski standard je istoveten z: EN 12413:2007/FprA1
ICS:
25.100.70 Brusiva Abrasives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 12413:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2010
ICS 25.100.70
English Version
Safety requirements for bonded abrasive products
Exigences de sécurité pour les produits abrasifs Sicherheitsanforderungen für Schleifkörper aus
agglomérés gebundenem Schleifmittel
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 143.
This draft amendment A1, if approved, will modify the European Standard EN 12413:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12413:2007/FprA1:2010: E
worldwide for CEN national Members.
SI
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...