Testing of welded joints of thermoplastics semi-finished products - Part 3: Tensile creep test

The addition of an Annex C - Testing of socket joints

Prüfen von Schweißverbindungen aus thermoplastischen Kunststoffen - Teil 3: Zeitstand­Zugversuch

Essai des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 3: Essai de fluage

Preskus zvarjenih spojev plastomernih polizdelkov - 3. del: Preskus lezenja pri natezni obremenitvi

General Information

Status
Withdrawn
Publication Date
30-Sep-2005
Withdrawal Date
30-Mar-2014
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
14-Mar-2014
Due Date
06-Apr-2014
Completion Date
31-Mar-2014

Relations

Buy Standard

Amendment
EN 12814-3:2000/A1:2005
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12814-3:2000/A1:2005
01-oktober-2005
Preskus zvarjenih spojev plastomernih polizdelkov - 3. del: Preskus lezenja pri
natezni obremenitvi
Testing of welded joints of thermoplastics semi-finished products - Part 3: Tensile creep
test
Prüfen von Schweißverbindungen aus thermoplastischen Kunststoffen - Teil 3: Zeitstand
­Zugversuch
Essai des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 3:
Essai de fluage
Ta slovenski standard je istoveten z: EN 12814-3:2000/A1:2005
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN 12814-3:2000/A1:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12814-3:2000/A1:2005

---------------------- Page: 2 ----------------------

SIST EN 12814-3:2000/A1:2005
EUROPEAN STANDARD
EN 12814-3:2000/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2005
ICS 25.160.40
English version
Testing of welded joints of thermoplastics semi-finished products
- Part 3: Tensile creep test
Essai des assemblages soudés sur produits semi-finis en Prüfen von Schweißverbindungen aus thermoplastischen
thermoplastiques - Partie 3: Essai de fluage Kunststoffen - Teil 3: Zeitstand-Zugversuch
This amendment A1 modifies the European Standard EN 12814-3:2000; it was approved by CEN on 19 May 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12814-3:2000/A1:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 12814-3:2000/A1:2005
EN 12814-3:2000/A1:2005 (E)
Contents Page
1 Modification in clause 6.4
2 Modification of Annex A .4
Annex A .2 (informative) Two notch creep test (2NCT).5
3 Modification of Annex B .7
4 Introduction of a new annex: Annex C .7
Annex C (informative) Testing of socket joints .8
C.1 Scope .8
C.2 Sampling procedure .8
C.3 Dimensions of test specimens.8
C.4 Cutting and preparation of test specimens.9
C.5 Mechanical testing.10
C.6 Evaluation.11
C.7 Test report .11

2

---------------------- Page: 4 ----------------------

SIST EN 12814-3:2000/A1:2005
EN 12814-3:2000/A1:2005 (E)
Foreword
This European Standard (EN 12814-3:2000/A1:2005) has been prepared by Technical Committee
CEN/TC 249 “Plastics”, the secretariat of which is held by IBN/BIN.
This Amendment to the European Standard EN 12814-3:2000 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by January 2006, and conflicting
national standards shall be withdrawn at the latest by January 2006.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 12814-3:2000/A1:2005
EN 12814-3:2000/A1:2005 (E)
1 Modification in clause 6
After the first paragraph, add the following Note:
NOTE In the case of socket joints, see Annex C.
2 Modification of Annex A
The actual Annex A shall be split in two parts and renamed: Notch Creep Test (NCT):
Annex A.1 Full notch creep test (FNCT) corresponding to the actual Annex A
Annex A.2 Two notch creep test (2NCT)
4

---------------------- Page: 6 ----------------------

SIST EN 12814-3:2000/A1:2005
EN 12814-3:2000/A1:2005 (E)
Annex A.2
(informative)

Two notch creep test (2NCT)
A.2-1 Principle
The resistance to slow crack growth of paren
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.