iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 163100:2016

(Main)

Sectional Specification: Film and hybrid integrated circuits

Sectional Specification: Film and hybrid integrated circuits

This sectional specification applies to F&HICs manufactured as catalogue products or as custom built products using thick film techniques and whose quality is assessed on the basis of qualification approval.
It presents preferred values for ratings and characteristics. It selects from CECC 63 000 the appropriate methods of test and gives generam performance requirements, to be used in detail specifications for F&HICs derived from this specification.
Passive networks can be qualified to this specification or to alternative specifications, when introduced. For resistor networks, see specification CECC 64 100.

Rahmenspezifikation: Integrierte Hybrid- und Schichtschaltungen

Spécification intermédiaire: Circuits intégrés hybride et à couches

Področna specifikacija: Tankoplastna in hibridna integrirana vezja

Ta področna specifikacija se uporablja za tankoplastna in hibridna integrirana vezja, ki so izdelana kot kataloški proizvodi ali proizvodi, izdelani po meri, na podlagi uporabe tehnik z debelo plastjo in katerih kakovost se ocenjuje na podlagi odobritve kvalifikacije.
Podaja prednostne vrednosti za nazivne vrednosti in lastnosti. Določa ustrezne preskusne metode iz specifikacije CECC 63 000 in podaja splošne zahteve glede zmogljivosti za uporabo v podrobnih specifikacijah za tankoplastna in hibridna integrirana vezja, ki izhajajo iz te specifikacije.
Pasivna omrežja so lahko kvalificirana v skladu s to specifikacijo ali drugimi specifikacijami, če se uporabljajo. Za uporovna omrežja glej specifikacijo CECC 64 100.

General Information

Status
Published
Publication Date
27-Sep-2016
ICS
31.200 - Integrated circuits. Microelectronics
Technical Committee
I11 - Imaginarni 11
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
28-Sep-2016
Due Date
03-Dec-2016
Completion Date
28-Sep-2016
Ref Project
EN 163100:1991 - Sectional Specification: Film and hybrid integrated circuits

Buy Standard

EN 163100:2016EN 163100:2016
PreviousNext
Standard
EN 163100:2016
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
EN 163100:2016 - dokument je brez vodnega pretiska, ker se pri izdelave premakne na sredino straniEN 163100:2016 - dokument je brez vodnega pretiska, ker se pri izdelave premakne na sredino strani
PreviousNext
Standard
EN 163100:2016 - dokument je brez vodnega pretiska, ker se pri izdelave premakne na sredino strani
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 163100:2016
01-november-2016
Področna specifikacija: Tankoplastna in hibridna integrirana vezja
Sectional Specification: Film and hybrid integrated circuits
Rahmenspezifikation: Integrierte Hybrid- und Schichtschaltungen
Spécification intermédiaire: Circuits intégrés hybride et à couches
Ta slovenski standard je istoveten z: EN 163100:1991
ICS:
31.200 Integrirana vezja, Integrated circuits.
mikroelektronika Microelectronics
SIST EN 163100:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 163100:2016

---------------------- Page: 2 ----------------------
SIST EN 163100:2016

---------------------- Page: 3 ----------------------
SIST EN 163100:2016

---------------------- Page: 4 ----------------------
SIST EN 163100:2016

---------------------- Page: 5 ----------------------
SIST EN 163100:2016

---------------------- Page: 6 ----------------------
SIST EN 163100:2016

---------------------- Page: 7 ----------------------
SIST EN 163100:2016

---------------------- Page: 8 ----------------------
SIST EN 163100:2016

---------------------- Page: 9 ----------------------
SIST EN 163100:2016

------------
...

SLOVENSKI STANDARD
SIST EN 163100:2016
01-november-2016
3RGURþQDVSHFLILNDFLMD7DQNRSODVWQDLQKLEULGQDLQWHJULUDQDYH]MD
Sectional Specification: Film and hybrid integrated circuits
Rahmenspezifikation: Integrierte Hybrid- und Schichtschaltungen
Spécification intermédiaire: Circuits intégrés hybride et à couches
Ta sl
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 62228-3:2019/AC:2023(Corrigendum)
Integrated circuits - EMC evaluation of transceivers - Part 3: CAN transceivers (IEC 62228-3:2019/COR1:2023)
EN IEC 62228-3:2019/AC:2023-07
  • Corrigendum
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61967-8:2023(Main)
Integrated circuits - Measurement of electromagnetic emissions - Part 8: Measurement of radiated emissions - IC stripline method (IEC 61967-8:2023)
EN IEC 61967-8:2023

IEC 61967-8:2023 is available as IEC 61967-8:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61967-8:2023 defines a method for measuring the electromagnetic radiated emission from an integrated circuit (IC) using an IC stripline. The IC being evaluated is mounted on an EMC test board (PCB) between the active conductor and the ground plane of the IC stripline arrangement. This edition includes the following significant technical changes with respect to the previous edition:
a) frequency range of 150 kHz to 3 GHz was deleted from the scope;
b) extension of upper usable frequency to 6 GHz or higher as long as the defined requirements are fulfilled.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60747-16-7:2023(Main)
Semiconductor devices - Part 16-7: Microwave integrated circuits - Attenuators (IEC 60747-16-7:2022)
EN IEC 60747-16-7:2023

This part of IEC 60747 specifies the terminology, essential ratings and characteristics, and measuring methods of microwave integrated circuit attenuators.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60747-16-8:2023(Main)
Semiconductor devices - Part 16-8: Microwave integrated circuits - Limiters (IEC 60747-16-8:2022)
EN IEC 60747-16-8:2023

This part of IEC 60747 specifies the terminology, essential ratings and characteristics, and measuring methods of microwave integrated circuit limiters.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62228-6:2023(Main)
Integrated circuit - EMC Evaluation of transceivers - Part 6: PSI5 transceivers (IEC 62228-6:2022)
EN IEC 62228-6:2022

This document specifies test and measurement methods for EMC evaluation of Peripheral Sensor Interface 5 (PSI5) transceiver integrated circuits (ICs) under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. It is applicable for PSI5 satellite ICs (e.g. sensors) and ICs with embedded PSI5 transceivers (e.g. PSI5 Electronic control unit IC). The document covers
- the emission of RF disturbances,
- the immunity against RF disturbances,
- the immunity against impulses and
- the immunity against electrostatic discharges (ESD).

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62228-7:2022(Main)
Integrated circuits - EMC evaluation of transceivers - Part 7: CXPI transceivers (IEC 62228-7:2022)
EN IEC 62228-7:2022

This part of IEC 62228 specifies test and measurement methods for the EMC evaluation of CXPI transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. This specification is applicable for standard CXPI transceiver ICs and ICs with embedded CXPI transceiver and covers
- the emission of RF disturbances,
- the immunity against RF disturbances,
- the immunity against impulses and
- the immunity against electrostatic discharges (ESD).

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62228-5:2021(Main)
Integrated circuits - EMC evaluation of transceivers - Part 5: Ethernet transceivers (IEC 62228-5:2021)
EN IEC 62228-5:2021

This part of IEC 62228 specifies test and measurement methods for EMC evaluation of Ethernet
transceiver ICs under network condition. It defines test configurations, test conditions, test
signals, failure criteria, test procedures, test setups and test boards. It is applicable for
transceiver of the Ethernet systems
• 100BASE-T1 according to ISO/IEC/IEEE 8802-3/AMD1;
• 100BASE-TX according to ISO/IEC/IEEE 8802-3;
• 1000BASE-T1 according to ISO/IEC/IEEE 8802-3/AMD4
and covers
• the emission of RF disturbances;
• the immunity against RF disturbances;
• the immunity against impulses;
• the immunity against electrostatic discharges (ESD).

  • Standard
    112 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61967-4:2021(Main)
Integrated circuits - Measurement of electromagnetic emissions - Part 4: Measurement of conducted emissions, 1 ohm/150 ohm direct coupling method (IEC 61967-4:2021)
EN IEC 61967-4:2021

This part of IEC 61967 specifies a method to measure the conducted electromagnetic emission
(EME) of integrated circuits by direct radio frequency (RF) current measurement with a
1 Ω resistive probe and RF voltage measurement using a 150 Ω coupling network. These
methods ensure a high degree of reproducibility and correlation of EME measurement results.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62433-6:2021(Main)
EMC IC modelling - Part 6: Models of integrated circuits for pulse immunity behavioural simulation - Conducted pulse immunity modelling (ICIM-CPI) (IEC 62433-6:2020)
EN IEC 62433-6:2020

The objective of this part of IEC 62433 is to describe the extraction flow for deriving an
immunity macro-model of an Integrated Circuit (IC) against conducted Electrostatic Discharge
(ESD) according to IEC 61000-4-2 and Electrical Fast Transients (EFT) according to
IEC 61000-4-4.
The model addresses physical damages due to overvoltage, thermal damage and other failure
modes. Functional failures can also be addressed.
This model allows the immunity simulation of the IC in an application. This model is commonly
called "Integrated Circuit Immunity Model Conducted Pulse Immunity", ICIM-CPI.
The described approach is suitable for modelling analogue, digital and mixed-signal ICs.
Several terminals of an IC can be part of a single model (e.g. input, output and supply pins).
The implementation of the model is capable of representing the non-linear behaviour of
overvoltage protection circuits.
The model can be implemented for the use in different software tools for circuit simulation in
time-domain. The described modelling approach allows simulating device failure due to ESD
or EFT at component and system level considering all components necessary for the immunity
simulation of an IC, such as a PCB or external protection elements.
This document demonstrates, in detail, the construction of models in a defined XML-based
format which is suitable for the exchange of models without any deeper knowledge of the
semiconductor circuit. However, the model functionality can be implemented in different
formats including, but not limited to, tables, SPICE[1] 1 netlists, hardware description
languages such as VHDL-AMS [2] and Verilog-AMS [3].
This document provides:
• the description of ICIM-CPI macro-model elements representing electrical, thermal or
logical behaviour of the IC.
• a universal data exchange format based on XML.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60747-16-5:2014/A1:2020(Amendment)
Semiconductor devices - Part 16-5: Microwave integrated circuits - Oscillators (IEC 60747-16-5:2013/A1:2020)
EN 60747-16-5:2013/A1:2020

The contents of the corrigendum of September 2020 have been included in this copy.

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day