SIST EN ISO 15610:2024
(Main)Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2024)
Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2024)
This document specifies how a welding procedure can be qualified by using tested welding consumable data. It expands on the requirements given in ISO 15607.
In addition, it gives the range of qualification.
Application of this document is limited to parent material groups 1.1, 8.1, 21, 22.1 and 22.2 in accordance with ISO/TR 15608, which produce acceptable microstructures and properties in the heat-affected zone which do not deteriorate significantly in service.
This document is limited to:
— parent material thicknesses t ≤ 40 mm (groups 1.1 and 8.1) and t ≤ 20 mm (groups 21, 22.1 and 22.2);
— fillet welds with throat thickness a ≥ 1 mm.
This document is not applicable when any of the following is specified for the welded joint:
a) hardness;
b) impact properties;
c) preheating;
d) controlled heat input;
e) interpass temperature;
f) post-weld heat treatment.
The use of this document can also be restricted by an application standard, specification or other documents.
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Qualifizierung aufgrund des Einsatzes von geprüften Schweißzusätzen (ISO 15610:2024)
Dieses Dokument legt fest, wie ein Schweißverfahren mithilfe von Daten über geprüfte Schweißzusätze qualifiziert werden kann. Es erweitert die Anforderungen von ISO 15607.
Zusätzlich gibt es den Geltungsbereich an.
Dieses Dokument ist anwendbar für Schweißprozesse nach Tabelle 1.
[Tabelle 1]
Die Anwendung dieses Dokuments beschränkt sich auf Grundwerkstoffe der Gruppen 1.1, 8.1, 21, 22.1 und 22.2 nach ISO/TR 15608, mit denen sich zulässige Mikrogefüge und Eigenschaften in der Wärmeeinflusszone ergeben, die sich im Betrieb nicht wesentlich verschlechtern.
Dieses Dokument beschränkt sich auf:
Stumpf- und Kehlnähte an Werkstoffdicken t ≤ 40 mm (Gruppen 1.1 und 8.1) und t ≤ 20 mm (Gruppen 21, 22.1 und 22.2);
Kehlnähte mit der Nahtdicke a ≥ 1 mm.
Dieses Dokument ist nicht anwendbar, wenn einer der folgenden Punkte für die Schweißverbindung festgelegt ist:
a) Härte;
b) Kerbschlagarbeit;
c) Vorwärmen;
d) geregelte Wärmeeinbringung;
e) Zwischenlagentemperatur;
f) Wärmebehandlung nach dem Schweißen.
Die Anwendung dieses Dokuments kann auch durch eine Anwendungsnorm, eine Spezifikation oder durch andere Dokumente eingeschränkt werden.
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Qualification basée sur des produits consommables soumis à essais (ISO 15610:2024)
Le présent document spécifie comment un mode opératoire de soudage peut être qualifié en utilisant des données relatives à des produits consommables de soudage soumis à essais. Il développe les exigences données dans la norme ISO 15607.
De plus, il donne le domaine de validité de la qualification.
L’application du présent document est limitée aux groupes de matériaux de base 1.1, 8.1, 21, 22.1 et 22.2 selon l’ISO/TR 15608, qui produisent des microstructures acceptables et des propriétés dans la zone affectée thermiquement qui ne se dégradent pas de façon significative en service.
L’application du présent document est limitée:
— aux épaisseurs de matériaux de base t ≤ 40 mm (groupes 1.1 et 8.1) et t ≤ 20 mm (groupes 21, 22.1 et 22.2;
— aux soudures d’angle avec une gorge a ≥ 1 mm.
Le présent document ne s'applique pas lorsque l'un des éléments suivants est spécifié pour l’assemblage soudés:
a) la dureté;
b) la résistance à la flexion par choc;
c) le préchauffage;
d) l’apport de chaleur contrôlé;
e) la température interpasse;
f) le traitement thermique après soudage.
L'emploi du présent document peut également être limité par une norme d'application, une spécification ou un autre document.
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Kvalifikacija na podlagi preskušenih dodajnih in pomožnih materialov (ISO 15610:2024)
Ta dokument določa način kvalifikacije varilnega postopka na podlagi podatkov o preskušenih dodajnih in pomožnih materialih. Dokument dopolnjuje zahteve, podane v standardu ISO 15607.
Poleg tega navaja tudi obseg kvalifikacije.
Uporaba tega dokumenta je omejena na skupine osnovnega materiala 1.1, 8.1, 21, 22.1 in 22.2 v skladu s standardom ISO/TR 15608, ki v območju pod vplivom toplote ustvarjajo sprejemljive mikrostrukture in lastnosti ter se med uporabo bistveno ne poslabšajo.
Ta dokument je omejen na:
– debeline osnovnega materiala t ≤ 40 mm (skupini 1.1 in 8.1) in t ≤ 20 mm (skupine 21, 22.1 in 22.2);
– kotne zvare z debelino grla a ≥ 1 mm.
Ta dokument se ne uporablja, če je za zvarjeni spoj določeno karkoli od naslednjega:
a) trdota;
b) udarne lastnosti;
c) predgrevanje;
d) nadzorovana toplotna moč;
e) medvarkovna temperatura;
f) toplotna obdelava po varjenju.
Uporabo tega dokumenta je mogoče omejiti tudi s standardom za uporabo, specifikacijo ali drugimi dokumenti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2024
Nadomešča:
SIST EN ISO 15610:2023
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Kvalifikacija na
podlagi preskušenih dodajnih in pomožnih materialov (ISO 15610:2024)
Specification and qualification of welding procedures for metallic materials - Qualification
based on tested welding consumables (ISO 15610:2024)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Qualifizierung aufgrund des Einsatzes von geprüften Schweißzusätzen (ISO
15610:2024)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Qualification basée sur des produits consommables soumis à essais (ISO
15610:2024)
Ta slovenski standard je istoveten z: EN ISO 15610:2024
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 15610
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2024
EUROPÄISCHE NORM
ICS 25.160.10 Supersedes EN ISO 15610:2023
English Version
Specification and qualification of welding procedures for
metallic materials - Qualification based on tested welding
consumables (ISO 15610:2024)
Descriptif et qualification d'un mode opératoire de Anforderung und Qualifizierung von Schweißverfahren
soudage pour les matériaux métalliques - Qualification für metallische Werkstoffe - Qualifizierung aufgrund
basée sur des produits consommables soumis à essais des Einsatzes von geprüften Schweißzusätzen (ISO
(ISO 15610:2024) 15610:2024)
This European Standard was approved by CEN on 5 February 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15610:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 15610:2024) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2024, and conflicting national standards
shall be withdrawn at the latest by September 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15610:2023.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 15610:2024 has been approved by CEN as EN ISO 15610:2024 without any modification.
International
Standard
ISO 15610
Third edition
Specification and qualification of
2024-03
welding procedures for metallic
materials — Qualification based on
tested welding consumables
Descriptif et qualification d'un mode opératoire de soudage pour
les matériaux métalliques — Qualification basée sur des produits
consommables soumis à essais
Reference number
ISO 15610:2024(en) © ISO 2024
ISO 15610:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 15610:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Limits of the application of this document . 2
4.1 Limits related to the welded joint .2
4.1.1 Parent material .2
4.1.2 Parent material thickness, t .3
4.1.3 Fillet weld throat thickness, a .3
4.2 Limits common to all welding processes .3
4.2.1 Multiple-process welding procedures .3
4.2.2 Welding positions .3
4.2.3 Welding consumables .3
4.2.4 Type of current .3
4.3 Limits specific for the welding process .3
4.3.1 Processes 131, 132, 133, 135, 136 and 138 .3
4.3.2 Processes 141 and 15 .3
4.3.3 Process 121 .3
5 Preliminary welding procedure specification (pWPS) . 4
6 Qualification of the pWPS . 4
7 Welding procedure qualification record (WPQR). 4
Annex A (informative) Example of a WPQR form. 5
Bibliography . 6
iii
ISO 15610:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 10, Quality management in the field of welding, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 121, Welding and allied processes, in accordance with
the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 15610:2023), of which it constitutes a minor
revision. The changes are as follows:
— scope reworded regarding butt and fillet welds.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www.iso.org/members.html. Official
interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
ISO 15610:2024(en)
Introduction
This document is a part of a group of standards dealing with specification and qualification of welding
procedure
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.