CEN/TC 264/WG 9 - Quality assurance of automated measuring systems
A three part standard for use in emissions and ambient air, which describes: a) The determination of the measurement uncertainty (ie a calibration curve and confidence interval by means of parallel measurements using a reference method) of an automated measurement system; b) The operational activities necessary to maintain the required quality of the measurement results, and check the calibration curve; c) A method for the annual surveillance of the AMS.
Quality assurance of automated measuring systems
A three part standard for use in emissions and ambient air, which describes: a) The determination of the measurement uncertainty (ie a calibration curve and confidence interval by means of parallel measurements using a reference method) of an automated measurement system; b) The operational activities necessary to maintain the required quality of the measurement results, and check the calibration curve; c) A method for the annual surveillance of the AMS.
General Information
This document specifies the performance criteria and test procedures for the performance test of stationary automated measuring systems (AMS) that continuously measure gases and particulate matter in, and flow of, the waste gas from stationary sources.
This document supports the requirements of particular EU Directives. It provides the detailed procedures covering the QAL1 requirements of EN 14181 and, where required, input data used in QAL3.
- Standard72 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the general performance criteria and test procedures for the performance test of portable automated measuring systems (P-AMS) used for periodic measurements of stationary source emissions. It applies to the performance test of P-AMS based on measurement techniques specified by the standard reference method (SRM) or an alternative method (AM).
The performance test is based on the general performance criteria and test procedures specified in this document and on the specific requirements specified for the SRM or AM. This includes testing of the applicability and correct implementation of the QA/QC procedures specified for the SRM or AM.
This document supports the requirements of particular EU Directives.
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for the manufacturer’s quality management system (QMS), the initial assessment of the manufacturer’s production control and the continuing surveillance of the effect of subsequent changes on the performance of certified air quality monitoring equipment (AQME).
This document also serves as a reference document for auditing the manufacturer’s QMS.
This document elaborates and supplements the requirements of EN ISO 9001:2015.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the general principles of certification, including common procedures and requirements, for the certification of air quality monitoring equipment (AQME).
This document applies to the certification of AQME for ambient air quality and emissions from stationary sources for which performance criteria and test procedures are available in European Standards.
This document provides for the certification of AQME according to the requirements of EN ISO/IEC 17065:2012.
This document elaborates and supplements the requirements of EN ISO/IEC 17065:2012 for bodies certifying AQME. It specifies requirements on testing laboratories as well as the manufacturer’s quality management system (QMS) and the surveillance for the manufacturing process as part of the certification process.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for the installation and on-going quality assurance and quality control of data acquisition and handling systems (DAHS). This includes requirements on:
- installation (Clause 5);
- quality assurance and quality control during QAL2 (Clause 6);
- quality assurance and quality control during on-going operation (Clause 7);
- annual functional test (Clause 8);
- documentation (Clause 9).
This document supports the requirements of EN 14181 and legislation such as the IED [1], MCPD [2] and E-PRTR [3]. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the performance test of data acquisition and handling systems (DAHS). This includes:
- specification of test procedures;
- description of laboratory tests;
- requirements on the testing laboratory.
This document supports the requirements of EN 14181 and legislation such as the IED, MCPD and E-PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the performance requirements on data acquisition and handling systems (DAHS) regarding implementation of the procedures defined in EN 17255-1 including
— data acquisition;
— data processing;
— data storage;
— data output;
— generation of reports;
— system functions;
— data security;
— documentation.
This document supports the requirements of EN 14181 and legislation such as the IED and E-PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this document are met and that these features do not adversely affect data quality, clarity or access.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the conversion of raw data from an automated measuring system (AMS) to reported data by a data acquisition and handling system (DAHS). This specification includes:
- requirements for the handling of data,
- requirements for the reporting of data,
- calculation procedures required.
The main items covered by this European Standard are given by, but not limited to raw data acquisition, raw data validation, data correction and data averaging.
This European Standard supports the requirements of EN 14181 and legislation such as the IED and E-PRTR. It does not preclude the use of additional features and functions provided the minimum requirements of this European Standard are met and that these features do not adversely affect data quality, clarity or access.
- Standard40 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies procedures for establishing quality assurance levels (QAL) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This European Standard specifies:
- a procedure (QAL2) to calibrate the AMS and determine the variability of the measured values obtained by it, so as to demonstrate the suitability of the AMS for its application, following its installation;
- a procedure (QAL3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS, by checking that the zero and span characteristics are consistent with those determined during QAL1;
- a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined.
This European Standard is designed to be used after the AMS has been certified in accordance with the series of European Standards EN 15267.
- Standard84 pagesEnglish languagesale 10% offe-Library read for1 day
This CEN Technical Report provides guidance for applying the European Standard EN 14181:2004.
This CEN Technical Report provides guidance only on applying the quality assurance levels QAL1, QAL2 and QAL3 as well as the Annual Surveillance Test (AST).
This CEN Technical Report is an informative document.
- Technical report45 pagesEnglish languagesale 10% offe-Library read for1 day
- Technical report44 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies procedures for establishing quality assurance levels (QALs) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This European Standard specifies procedures for establishing quality assurance levels (QALs) for automated measuring systems (AMS) installed on industrial plants for the determination of the flue gas components and other flue gas parameters.
This standard specifies:
- a procedure (QAL 2) to calibrate the AMS and determine the variability of the measured values obtained by an automated measurement system which is suitable for the validation of an AMS following its installation;
- a procedure (QAL 3) to maintain and demonstrate the required quality of the measurement results during the normal operation of an AMS, by checking that the zero and span characteristics are consistent with those determined during QAL 1;
- a procedure for the annual surveillance tests (AST) of the AMS in order to evaluate (i) that it functions correctly and its performance remains valid and (ii) that its calibration function and variability remain as previously determined.
This standard is designed to be used after the AMS has been accepted according to the procedures specified in EN ISO 14956 (QAL 1).
This standard is restricted to quality assurance (QA) of the AMS, and does not include QA of the data collection and recording system of the plant.
- Standard59 pagesEnglish languagesale 10% offe-Library read for1 day