CEN/TC 334 - Irrigation techniques

ISO 13693-1:2013 specifies the general requirements and test methods for small plastics-bodied valves used for chemigation, intended for operation in irrigation pipe systems which may contain fertilizers and chemicals of the type and concentration used in agriculture.
It is applicable to controllable safety devices (also known as backflow preventers) with a reduced pressure zone (RPZ), intended to prevent backflow by back-siphonage or backpressure of irrigation water into an upstream potable water distribution system, whenever the pressure in the latter is lower than that in the system located downstream.
It is applicable to such devices of nominal size up to and including DN 50 (2"), with a nominal pressure of PN10, that are capable of working without modification or adjustment at any pressure up to 1 MPa (10 bar), with any pressure variation up to 1 MPa (10 bar), and in permanent duty at temperatures up to 45 °C and for 1 h at 65 °C.

This European standard specifies the test methods in the laboratory and in the field.

ISO 9261:2004 gives mechanical and functional requirements for agricultural irrigation emitters and emitting pipes, and, where applicable, their fittings, and provides methods for testing conformity with such requirements. It also specifies the data to be supplied by the manufacturer to permit correct information, installation and operation in the field. It is applicable to emitters, emitting and dripping (trickling) pipes, hoses, including collapsible hoses ("tapes") and tubing of which the emitting units form an integral part, to emitters and emitting units with or without pressure regulation and with flow rates not exceeding 24 l/h per outlet (except during flushing), as well as to fittings dedicated to the connection of emitting pipes, hoses and tubing. It is not applicable to porous pipe (pipe that is porous along its entire length), nor does it cover the performance of pipes as regards clogging.

ISO 11545:2009 specifies an in-field method for determining the uniformity of water distribution in the field from centre-pivot and moving lateral irrigation machines equipped with sprayer or sprinkler nozzles. The calculation of the coefficient of uniformity is also specified.
It is applicable to agricultural irrigation machines for which the water application device is more than 1,5 m above the soil surface and for which the water distribution from successive devices overlaps. It is not applicable to the evaluation of centre-pivot irrigation machines equipped with various corner arm application devices.

This document applies to irrigation hydrants intended to supply equipment for use in water distribution irrigation networks. The range of PN is that defined in EN 1074-1, i.e.: PN 10, PN 16, PN 25 and limited to PN 25.

This part of EN 15099 establishes the definitions, functionalities and specifications related to remote monitoring and control for irrigation systems and its elements.

The purpose of this Standard is to describe a localised irrigation hydraulic system and to specify a method to determine the uniformity in water distribution for each installation to be evaluated in the field.
This document applies to localised irrigation systems. It does not cover management practices.
This paper defines the methodology to be applied in the farm localised irrigation system evaluation.

TC - Modification to 6.1.1

UAP of 3 months applies.
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

This European Standard applies to meters fitted to irrigation machines and networks. These meters are used to meter the actual volume of irrigation water flowing through a fully charged, closed pipe, in order to manage consumption, and to invoice the volume of water distributed.
Irrigation water is likely to contain mineral and organic particles.

This document provides guidelines to choose material, to design, to prepare plans, and to install a solid set irrigation system to apply water to the irrigated area with the greatest possible efficiency.
This document covers sprinkler irrigation systems installed at the beginning of the irrigation season and removed at the end without moving any component, sprinkler or pipe, during the entire irrigation season.
It covers only solid set system components located on the field and upstream from a water supply point defined by a pressure and a flow.
This document does not cover permanent systems with buried pipes nor hand-movable portable systems.

This document provides a document to check and test, the proper operation and performance of a solid set irrigation system installed according to relevant design documents specified in EN 13742-1.

This document applies to irrigation hydrants intended to supply equipment for use in water distribution irrigation networks. The range of PN is that defined in EN 1074-1, i.e.: PN 10, PN 16, PN 25 and limited to PN 25.

This standard provides:
- principles and formulas for calculating water application intensity under sprinkler irrigation systems (fixed and moving);
- test methods and guidelines for measuring water application intensity under the different systems in laboratory and in field conditions.
It applies to stationary sprinkling systems: solid set sprinkler systems, automatic turf irrigation systems, sprinklers and sprayer for microirrigation systems, and to moving sprinkling systems: reel machine systems, centre pivot and moving laterals systems.

This standard describes the technical characteristics and requirements of hydraulic connection and control accessories to ensure a sufficient mechanical resistance for practical use, and specifies the relevant testing methods. It applies to accessories made of steel, brass, aluminium, Polypropylene, Polyethylene or PVC for use in irrigation systems up to a diameter of 250 mm.

ISO 8224-1:2002 specifies the operational characteristics of, and laboratory and field test methods for, traveller irrigation machines. It includes user-oriented technical information for presentation in the manufacturer's accompanying product literature, laboratory test procedures for evaluating the uniformity of water application on an irrigated strip by a machine operating within a specified range of conditions and for determining the maximum travelling rates the drive mechanism is able to achieve in response to specified operating conditions, and field test procedures for determining the uniformity of water application on a given irrigated strip under local conditions prevailing in the field at time of testing.
It is applicable only to traveller irrigation machine types, and not to other types such as centre-pivot or lateral irrigation machines.

This European Standard specifies the installation methods and the automatic turf irrigation system handover.
Annex A should be used as a check list for system handover (excluding pump stations).

This European Standard provides a document to test the performance of uniformity of water distribution of an automatic turf irrigation system in order to commission the system.

This European Standard specifies the technical and functional characteristics that shall be indicated by manufacturers of localised irrigation systems for user information to aid them in their choice of facilities and materials.
This standard is related to others that will be drawn up for each system component (technical characteristics and test methods).
This European standard defines localised irrigation systems, characterising the various components which comprise them.

This part of this European standard EN12484 is intended to:  - provide rules for the presentation of the user manual, installation manual, and trouble shooting guide;  - guide the owner and/or the project manager in their choice for the most efficient control system, adapted to their needs and constraints;  - define rules for minimum compatibility among different makes of control systems.

This part of this European Standard EN 12484 is intended to: - set forth the information and requirements taken into account by to project manager for designing an automatic irrigation system and justify the technical decisions made; - quantify and define the equipment and methods used as a basis for carrying out the installation of an automatic irrigation system.

This standard specifies the conditions of suitability for application of quick coupling pipes for movable irrigation supply made of steel, aluminium, PE or rigid PVC used in irrigation systems. Standards for PE or PVC are not applicable for quick coupling pipes.

This European Standard specifies the standard layouts of documents intended to guide the users while establishing programmes of equipment for field equipment featuring one or more reel-machine(s), and while reviewing estimates.

This European standard specifies the characteristics that are required for the polyethylene (PE) tubes for irrigation reel machines. Those tubes are destined to be coiled onto structures of reel machines that conform to the size series specified in EN 12324-1, and to achieve the functions of carrying water and dragging the water emitting system, while it travels along the irrigated lane.

This European Standard specifies the way in which the characteristics of reel machines shall be presented by the manufacturer.

This Europeans Standard defines and specifies the different outstanding terms and classifications in the field of center pivots and moving laterals systems, necessary for the understanding of EN 12325-1 and prEN 12325-2. This standard is applicable to fixed and movable pivots, as well as to the different categories of moving laterals.

This European Standard defines and specifies the minimum performances of the machines. It gives a minimum quality level to which the manufacturers shall refer to. It takes in account the mechanical, electrical, hydraulic and agronomic aspects. This standard is to be applied to fixed and movable center pivots as well as to the different categories of moving laterals. This standard doesn't deal with safety problems; those aspects are treated in EN 909. This standard doesn't deal with specific problems for impact on environment.

CMC - Cross-references mistakes generated at editing

This part of pr EN 12484 specifies the data, irrigation needs, constraints and requirements which have to be presented and quantified by the owner in order to initiate system design, equipment sizing and realisation of automatic turf irrigation system.  This part of prEN 12484 is applicable to  irrigation projects with a surface larger than 1 ha such as golf courses, race courses, large municipal parks and sports fields.

This part of prEN 12325 gives the technical characteristics of the different components elements of fixed or movable pivot and moving lateral systems to be specified by the supplier : general characteristics (structures, advancing, electrical equipment), hydraulic characteristics and sprinkler characteristics.  This standard can be used as a presentation guideline for machine characteristics when replying to a call for tenders or when making delivery to the customer.

This part of prEN 12324 gives the dimensional specifications of the reel machine structures and of the corresponding polyethylene tubes.

This standard specifies the hydraulic and mechanical features necessary for defining the functioning of the emitting devices, whether or not equipped with compensating features, designed for use in localised irrigation systems.
The manner in which the manufacturers shall provide the basic engineering information for the design and use of the localised irrigation systems and the appropriate testing methods for checking and assuring the proper working order thereof are specified.
This standard applies to all the emitting devices listed in EN 13635:2001, 3.1, with the following restrictions:
- Micro-sprinklers, micro-sprayers or micro-jets are dealt with solely as components which aim is to wet a predetermined restricted area
   - Porous pipes are not included under this standard as a result of deeming the hydraulic features thereof to differ from the rest of the emitting devices.
   - Other devices such as misters, the essential function of which is that of creating a moist atmosphere more than watering as such, are not included.

This European standard specifies the test methods in the field.