ASTM A623-05

Standard Specification for Tin Mill Products, General Requirements

SCOPE
1.1 This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products.
1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named. Note 1 A complete metric companion to Specification A 623 has been developed-Specification A 623M; therefore no metric equivalents are presented in this specification.
The following safety caveat pertains to through of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Aug-2005
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.20 - Tin Mill Products

Relations

• Replaces: ASTM A623-03 - Standard Specification for Tin Mill Products, General Requirements
• Effective Date: 01-Sep-2005
• Replaced By: ASTM A623-06 - Standard Specification for Tin Mill Products, General Requirements
• Effective Date: 01-Mar-2006
• Referred By: ASTM A650/A650M-18 - Standard Specification for Tin Mill Products, Black Plate, Double Reduced
• Effective Date: 01-Sep-2005
• Referred By: ASTM A625/A625M-13(2018) - Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
• Effective Date: 01-Sep-2005
• Referred By: ASTM A599/A599M-07(2017) - Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
• Effective Date: 01-Sep-2005
• Referred By: ASTM A987/A987M-19 - Standard Practice for Measuring Shape Characteristics of Tin Mill Products
• Effective Date: 01-Sep-2005
• Referred By: ASTM D5833-12(2020) - Standard Guide for Source Reduction Reuse, Recycling, or Disposal of Steel Cans
• Effective Date: 01-Sep-2005
• Referred By: ASTM B545-22 - Standard Specification for Electrodeposited Coatings of Tin
• Effective Date: 01-Sep-2005
• Referred By: ASTM A657/A657M-18 - Standard Specification for Tin Mill Products, Black Plate Electrolytic Chromium-Coated, Single and Double Reduced
• Effective Date: 01-Sep-2005
• Referred By: ASTM A623M-22 - Standard Specification for Tin Mill Products, General Requirements [Metric]
• Effective Date: 01-Sep-2005
• Referred By: ASTM A370-23 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products
• Effective Date: 01-Sep-2005
• Referred By: ASTM A624/A624M-22 - Standard Specification for Tin Mill Products, Electrolytic Tin Plate, Single Reduced
• Effective Date: 01-Sep-2005
• Referred By: ASTM E18-22 - Standard Test Methods for Rockwell Hardness of Metallic Materials
• Effective Date: 01-Sep-2005
• Referred By: ASTM A626/A626M-22 - Standard Specification for Tin Mill Products, Electrolytic Tin Plate, Double Reduced
• Effective Date: 01-Sep-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 623 – 05
Standard Specification for
1
Tin Mill Products, General Requirements
This standard is issued under the fixed designation A 623; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2.2 U.S. Military Standards:
3
MIL-STD-129 Marking for Shipment and Storage
1.1 This specification covers a group of common require-
MIL-STD-163 SteelMillProducts,PreparationforMarking
ments which, unless otherwise specified in the purchase order
3
and Storage
or in an individual specification, shall apply to tin mill
2.3 U.S. Federal Standard:
products.
Federal Std. No. 123 Marking for Shipment (Civil Agen-
1.2 Incaseofanyconflictinrequirements,therequirements
3
cies)
ofthepurchaseorder,theindividualmaterialspecification,and
this general specification shall prevail in the sequence named.
3. Terminology
NOTE 1—A complete metric companion to Specification A623 has
3.1 Definitions:
been developed—Specification A623M; therefore no metric equivalents
3.1.1 base box, n—aunitofareaequivalentto112sheets14
are presented in this specification.
2 2
by 20 in. or 31360 in. (217.78 ft ) (see Annex A1).
1.3 The following safety caveat pertains to Annex A3
3.1.2 base weight, n—a term used to describe the thickness
through Annex A10 of this specification: This standard does
of tin mill products. The designated base weight multiplied by
not purport to address all of the safety concerns, if any,
a factor of 0.00011 is the nominal decimal thickness, in inches
associated with its use. It is the responsibility of the user of this
of the material. Although it is customary industry-wide to use
standard to establish appropriate safety and health practices
the term “pound” (for example, 75 lb), following the base
and determine the applicability of regulatory limitations prior
weightdesignation,baseweightiscorrectlyusedonlytodefine
to use.
nominal material thickness, and is not a measure of the weight
of a base box.
2. Referenced Documents
3.1.3 black plate, n—light-gage, low-carbon, cold-reduced
2
2.1 ASTM Standards:
steelintendedforuseintheuntinnedstateorfortheproduction
A370 TestMethodsandDefinitionsforMechanicalTesting
of other tin mill products. It is supplied only in a dry or oiled
of Steel Products
condition.
A700 Practices for Packaging, Marking, and Loading
3.1.4 box annealing, n—aprocessinvolvingslowheatingof
Methods for Steel Products for Domestic Shipment
coils to a subcritical temperature, holding, and cooling there-
A987 Test Method for Measuring Shape Characteristics of
from, to soften the strip and relieve stresses produced during
Tin Mill Products
cold reduction. It is accomplished in a sealed container. By
D1125 Test Methods for Electrical Conductivity and Re-
introducing and maintaining an inert or slightly reducing
sistivity of Water
atmosphere during the cycle, a relatively bright surface is
E18 Test Methods for Rockwell Hardness and Rockwell
obtained.
Superficial Hardness of Metallic Materials
3.1.5 bright finish, n—a surface that has a melted tin
E112 Test Methods for Determining the Average Grain
coating.
Size
3.1.6 bundle, n—a unit containing two or more packages of
a cut size, supported by a platform, generally consisting of ten
or more packages. (Also commonly referred to as a multiple-
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel,
package lift containing two or more packages.)
Stainless Steel, and RelatedAlloys and is the direct responsibility of Subcommittee
A01.20 on Tin Mill Products.
3.1.7 burr, n—metal displaced beyond the plane of the
CurrenteditionapprovedSeptember1,2005.PublishedOctober2005.Originally
surface by slitting or shearing (see 9.1.7 and 9.2.6).
approved in 1968. Last previous edition approved in 2003 as A623-03.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
the ASTM website. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 623–05
3.1.8 camber, n—the greatest deviation of a coil edge from 3.1.17 length dimension—the longer dimension of a cut
a straight line. The measurement is taken on th
...