iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM A1025-05

(Specification)

Standard Specification for Ferroalloys, General Requirements

Standard Specification for Ferroalloys, General Requirements

ABSTRACT
This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials. The chemical analysis method shall be agreed upon by the purchaser and supplier. Unless otherwise specified, the material shall be sampled for determination of chemical composition and size.
SCOPE
1.1 This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials under each of the following ASTM specifications:
1.2 This specification also covers a group of supplementary requirements which may be applied to the above specifications as indicated therein. These are provided for use when additional testing or inspection is desired and apply only when specified individually by the purchaser in the order.
1.3 In case of conflict between the requirements of the individual specification and this general specification, the former shall prevail.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
28-Feb-2005
ICS
77.100 - Ferroalloys
Technical Committee
A01 - Steel, Stainless Steel and Related Alloys
Drafting Committee
A01.18 - Castings
Current Stage
Ref Project

Relations

Replaces
ASTM A1025-02 - Standard Specification for Ferroalloys, General Requirements
Effective Date
01-Mar-2005
Replaced By
ASTM A1025-05(2010) - Standard Specification for Ferroalloys, General Requirements
Effective Date
01-Apr-2010

Buy Standard

ASTM A1025-05 - Standard Specification for Ferroalloys, General RequirementsASTM A1025-05 - Standard Specification for Ferroalloys, General Requirements
PreviousNext
Technical specification
ASTM A1025-05 - Standard Specification for Ferroalloys, General Requirements
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation: A1025 – 05
Standard Specification for
Ferroalloys and Other Alloying Materials, General
1
Requirements
This standard is issued under the fixed designation A1025; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers a group of common require- 2.1 ASTM Standards:
ments that, unless otherwise specified in an individual speci- A99 Specification for Ferromanganese
fication, shall apply to ferroalloys and other alloying materials A100 Specification for Ferrosilicon
under each of the following ASTM specifications: A101 Specification for Ferrochromium
A102 Specification for Ferrovanadium
Title of Specification ASTM Designation
Ferromanganese A99
A132 Specification for Ferromolybdenum
Ferrosilicon A100
A146 Specification for Molybdenum Oxide Products
Ferrochromium A101
A323 Specification for Ferroboron
Ferrovanadium A102
Ferromolybdenum A132
A324 Specification for Ferrotitanium
Molybdenum Oxide Products A146
A481 Specification for Chromium Metal
Ferroboron A323
A482 Specification for Ferrochrome-Silicon
Ferrotitanium A324
Chromium Metal A481
A483 Specification for Silicomanganese
Ferrochrome-Silicon A482
A495 Specification for Calcium-Silicon Alloys
Silicomanganese A483
Calcium-Silicon Alloys A495 A550 Specification for Ferrocolumbium
Ferrocolumbium A550
A601 Specification for Electrolytic Manganese Metal
Electrolytic Manganese Metal A601
A610 Test Methods for Sampling and Testing Ferroalloys
Nickel Oxide Sinter A636
Ferromanganese Silicon A701 for Determination of Size
Titanium Scrap for Use in Deoxidation and Alloying of Steel A845
A636 Specification for Nickel Oxide Sinter
Aluminum Scrap for Use in Deoxidation and Alloying of Steel A846
A701 Specification for Ferromanganese-Silicon
Silicon Metal A922
A845 Specification for Titanium Scrap for Use in Deoxida-
1.2 This specification also covers a group of supplementary 3
tion and Alloying of Steel
requirements which may be applied to the above specifications
A846 Specification for Aluminum Scrap for Use in Deoxi-
as indicated therein. These are provided for use when addi- 3
dation and Alloying of Steel
tional testing or inspection is desired and apply only when
A922 Specification for Silicon Metal
specified individually by the purchaser in the order.
E29 Practice for Using Significant Digits in Test Data to
1.3 In case of conflict between the requirements of the
Determine Conformance with Specifications
individual specification and this general specification, the
E32 Practices for Sampling Ferroalloys and SteelAdditives
former shall prevail.
for Determination of Chemical Composition
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Ordering Information
responsibility of the user of this standard to establish appro-
3.1 Orders for material should include the following as
priate safety and health practices and determine the applica-
required, to describe the material adequately:
bility of regulatory requirements prior to use.
1 2
This specification is under the jurisdiction of ASTM Committee A01 on Steel, For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
A01.18 on Castings. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved March 1, 2005. Published March 2005. Originally the ASTM website.
3
approved in 2002. Last previous edition approved in 2002 as A1025 - 02. DOI: Withdrawn. The last approved version of this historical standard is referenced
10.1520/A1025-05. on www.astm.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A1025 – 05
3.1.1 ASTM designation and year of issue, 6. Inspection
3.1.2 Grade of material,
6.1 The manufacturer shall afford the inspector representing
3.1.3 Size of material,
thepurchaserallreasonablefacilities,withoutcharge,tosatisfy
3.1.4 Quantity,
the purchaser that the material is being furnished in accordance
3.1.5 Packaging requirements, and
with the material specification.
3.1.6 Supplementary requirements desired, including the
7. Rejection
standards of acceptance.
7.1 Any rejections based on tests made in accordance with
4. Chemical Analysis the material specification shall be reported to the manufac
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM A941-23(Terminology)
Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

SCOPE
1.1 This standard is a compilation of definitions of terms related to steel, stainless steel, related alloys, and ferroalloys.  
1.2 When a term is used in an ASTM document for which Committee A01 is responsible, it is included herein only when judged, after review by Subcommittee A01.92, to be a generally usable term.  
1.3 Some definitions include a discussion section, which is a mandatory part of the definition and contains additional information that is relevant to the meaning of the defined term.  
1.4 Definitions of terms specific to a particular standard will appear in that standard and will supersede any definitions of identical terms in this standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM A957/A957M-21(Specification)
Standard Specification for Investment Castings, Steel and Alloy, Common Requirements, for General Industrial Use

ABSTRACT
This specification covers a group of requirements that are mandatory for castings produced by the investment casting process to meet the metallurgical requirements of the following steel casting specifications. Chemical, heat, and product analyses shall be performed wherein the material shall meet the specified composition limits for carbon, manganese, silicon, phosphorus, sulfur, nickel, chromium, molybdenum, vanadium, tungsten, copper, and aluminum. The specified design and dimensions of the ICI test bar shall be employed only for austenitic alloy castings. The material shall conform to mechanical properties including tension test requirements.
SCOPE
1.1 This specification covers a group of requirements that are mandatory for castings produced by the investment casting process to meet the metallurgical requirements of the following steel casting specifications issued by ASTM.    
ASTM Designation  
Title of Specification    
A27/A27M  
Steel Castings, Carbon, for General Application    
A128/A128M  
Steel Castings, Austenitic Manganese  
A148/A148M  
Steel Castings, High-Strength, for Structural Purposes    
A297/A297M  
Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat-Resistant, for General Application    
A447/A447M  
Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service    
A494/A494M  
Castings, Nickel and Nickel Alloy    
A560/A560M  
Castings, Chromium-Nickel Alloy    
A732/A732M  
Castings, Investment, Carbon and Low-Alloy Steel for General Application, and Cobalt Alloy for High Strength at Elevated Temperatures    
A743/A743M  
Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion-Resistant, for General Application    
A744/A744M  
Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service    
A747/A747M  
Steel Castings, Stainless, Precipitation Hardening    
A890/A890M  
Castings, Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant, Duplex (Austenitic/Ferritic) for General Application    
A915/A915M  
Steel Castings, Carbon and Alloy, Chemical Requirements Similar to Standard Wrought Grades    
A958/A958M  
Steel Castings, Carbon and Alloy, with Tensile Requirements, Chemical Requirements Similar to Standard Wrought Grades  
A1002  
Castings, Nickel-Aluminum Ordered Alloy  
1.2 This specification also covers a group of supplementary requirements that may be applied to the above specifications as indicated therein. These are provided for use when additional testing or inspection is desired, and apply only when specified individually by the purchaser in the order.  
1.3 When investment castings are ordered, the requirements stated in this specification form an integral part of the material specification. In cases of conflict, the requirements of this specification shall take precedence over the individual material specification requirements.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM A550-16(2021)(Specification)
Standard Specification for Ferrocolumbium (Ferroniobium)

ABSTRACT
This specification covers three grades of ferrocolumbium, designated low-alloy steel grade, alloy and stainless steel grade, and high-purity grade. The material shall conform to the requirements as to chemical composition. Also, the ferrocolumbium shall be available in the sizes and tolerances specified.
SCOPE
1.1 This specification covers three grades of Ferrocolumbium (ferroniobium), designated Low-Alloy Steel Grade, Alloy and Stainless Steel Grade, and High-Purity Grade.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A482/A482M-11(2021)(Specification)
Standard Specification for Ferrochrome-Silicon

ABSTRACT
This specification covers ferrochrome-silicon of Grades A and B. Chemical analysis shall be performed wherein specimens shall conform to required chemical composition of chromium, carbon, silicon, sulfur, phosphorus, nitrogen, manganese, nickel, vanadium, copper, molybdenum, columbium, tantalum, cobalt, aluminum, titanium, zirconium, arsenic, lead, tin, zinc, boron, antimony, silver, and bismuth.
SCOPE
1.1 This specification covers several grades of ferrochrome-silicon.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.2.1 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.  
1.2.2 Within the text, the SI units are shown in brackets.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A835/A835M-10(2020)(Specification)
Standard Specification for Sizes of Ferroalloys and Alloy Additives

ABSTRACT
This specification covers standards for sizes of screened ferroalloys and alloy additives. Products shall conform to specified nominal size, standard ordered size, maximum allowable oversize, maximum allowable undersize, and friability rating. Description of the friability ratings of the ferroalloys is also provided.
SCOPE
1.1 This specification covers standard nominal sizes and size tolerances of screened ferroalloy and alloy additive products. This specification provides a range of sizes as referenced in all ASTM specifications for ferroalloys and alloy additives.  
1.2 The sizes and tolerances allow for varying degrees of friability upon receipt of material since some attrition may be expected in transit, storage, and handling.  
1.3 Specifications of sieve sizes used to define tolerances are listed in Specification E11. Representative procedures for evaluation of each lot are described in Test Methods A610. Refer to Appendix X1 for applicable sieve designations (see Table X1.1).  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets); however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A483/A483M-10(2020)(Specification)
Standard Specification for Silicomanganese

ABSTRACT
This specification covers standards for silicomanganese of Grades A, B, and C. Materials shall conform to manganese, silicon, carbon, phosphorus, and sulfur contents, as well as supplemental requirements of arsenic, tin, lead, chromium, nickel, and molybdenum. The material shall also conform to standard sizes and tolerances.
SCOPE
1.1 This specification covers grades of silicomanganese.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.2.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets); however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A323-05(2020)(Specification)
Standard Specification for Ferroboron

ABSTRACT
This specification covers several grades of ferroboron. The grades shall conform to the required chemical composition for boron, carbon, silicon, and aluminum. Various sizes of ferroboron are detailed. Chemical analysis of the material shall be made.
SCOPE
1.1 This specification covers several grades of ferroboron.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A701/A701M-10(2020)(Specification)
Standard Specification for Ferromanganese-Silicon

ABSTRACT
This specification covers ferromanganese-silicon alloy. The alloys which are available in different sizes shall conform to the required chemical composition for manganese, carbon, silicon, phosphorus, arsenic, tin, lead, and chromium.
SCOPE
1.1 This specification covers a manganese-silicon alloy.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.2.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets); however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A1025/A1025M-10(2020)(Specification)
Standard Specification for Ferroalloys and Other Alloying Materials, General Requirements

ABSTRACT
This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials. The chemical analysis method shall be agreed upon by the purchaser and supplier. Unless otherwise specified, the material shall be sampled for determination of chemical composition and size.
SCOPE
1.1 This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials under each of the following ASTM specifications:    
Title of Specification  
ASTM Designation  
Ferromanganese  
A99  
Ferrosilicon  
A100  
Ferrochromium  
A101  
Ferrovanadium  
A102  
Ferromolybdenum  
A132  
Molybdenum Oxide Products  
A146  
Ferroboron  
A323  
Ferrotitanium  
A324  
Chromium Metal  
A481  
Ferrochrome-Silicon  
A482/A482M  
Silicomanganese  
A483/A483M  
Calcium-Silicon Alloys  
A495  
Ferrocolumbium  
A550  
Electrolytic Manganese Metal  
A601/A601M  
Nickel Oxide Sinter  
A636  
Ferromanganese Silicon  
A701/A701M  
Titanium Scrap for Use in Deoxidation and Alloying of Steel  
A845  
Aluminum Scrap for Use in Deoxidation and Alloying of Steel  
A846  
Silicon Metal  
A922  
1.2 This specification also covers a group of supplementary requirements which may be applied to the above specifications as indicated therein. These are provided for use when additional testing or inspection is desired and apply only when specified individually by the purchaser in the order.  
1.3 In case of conflict between the requirements of the individual specification and this general specification, the former shall prevail.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets); however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM A102-04(2019)(Specification)
Standard Specification for Ferrovanadium

ABSTRACT
This specification covers different sizes of one grade of ferrovanadium. The material shall undergo chemical analysis and shall conform to the requirements as to composition of the following chemical elements: vanadium, carbon, silicon, aluminum, sulfur, and phosphorus.
SCOPE
1.1 This specification covers one grade of ferrovanadium.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off