ASTM D6083/D6083M-21
(Specification)Standard Specification for Liquid-Applied Acrylic Coating Used in Roofing
Standard Specification for Liquid-Applied Acrylic Coating Used in Roofing
SCOPE
1.1 This specification covers liquid-applied water-dispersed acrylic latex elastomeric protective roof coatings.
1.2 This specification does not provide guidance for application.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D6083/D6083M −21
Standard Specification for
1
Liquid-Applied Acrylic Coating Used in Roofing
This standard is issued under the fixed designation D6083/D6083M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1079 Terminology Relating to Roofing and Waterproofing
D1644 Test Methods for Nonvolatile Content of Varnishes
1.1 This specification covers liquid-applied water-dispersed
D1653 Test Methods for Water Vapor Transmission of Or-
acrylic latex elastomeric protective roof coatings.
ganic Coating Films
1.2 This specification does not provide guidance for appli-
D2196 Test Methods for Rheological Properties of Non-
cation.
Newtonian Materials by Rotational Viscometer
1.3 The values stated in either SI units or inch-pound units D2370 Test Method for Tensile Properties of Organic Coat-
ings
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each D2697 Test Method for Volume Nonvolatile Matter in Clear
or Pigmented Coatings
system shall be used independently of the other. Combining
values from the two systems may result in nonconformance D4798/D4798M Practice for Accelerated Weathering Test
Conditions and Procedures for Bituminous Materials
with the standard.
(Xenon-Arc Method)
1.4 This standard does not purport to address all of the
G21 Practice for Determining Resistance of Synthetic Poly-
safety concerns, if any, associated with its use. It is the
meric Materials to Fungi
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter-
3. Terminology
mine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accor-
3.1 For definitions of terms used in this specification, see
dance with internationally recognized principles on standard-
Terminologies D16 and D1079.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4. Classification
mendations issued by the World Trade Organization Technical
4.1 Type I and Type II are defined by the liquid physical
Barriers to Trade (TBT) Committee.
properties in Table 1 and cured film physical properties in
Table 2.
2. Referenced Documents
2
2.1 ASTM Standards:
5. Materials and Manufacture
D16 TerminologyforPaint,RelatedCoatings,Materials,and
Applications 5.1 Composition—The product, as manufactured, shall be in
D471 Test Method for Rubber Property—Effect of Liquids liquid form for application to the roof surface by brushing,
D522/D522M Test Methods for Mandrel Bend Test of At- squeegeeing, rolling, or spraying. The product shall be com-
tached Organic Coatings posed of a water-based acrylic latex elastomeric emulsion
D624 Test Method for Tear Strength of Conventional Vul- polymer, to which various pigments and other additives have
been added to give the required physical properties.
canized Rubber and Thermoplastic Elastomers
D903 Test Method for Peel or Stripping Strength of Adhe-
sive Bonds 6. Liquid and Cured Film Physical Properties
6.1 Although the product is supplied as a liquid, its perfor-
1
This specification is under the jurisdiction of ASTM Committee D08 on
mance is based on the functional properties of the cured
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.09
materialinfilmform.Thecoatingisformedintoafilmadhered
on Bituminous Emulsions.
Current edition approved Feb. 15, 2021. Published February 2021. Originally to the substrate.
approved in 1997. Last previous edition approved in 2018 as D6083/D6083M – 18.
6.2 Liquid Physical Property Requirements—The liquid
DOI: 10.1520/D6083_D6083M-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or coatingshallcomplywiththepropertyrequirementsinTable1.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.3 Cured Film Physical Property Requirements—The
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. cured film shall comply with the requirements listed inTable 2.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6083/D6083M−21
TABLE 1 Liquid Physical Property Requirements
[0.020 in.] 6 10 % film submerged in distilled water for a
Requirements period of 168 6 4 h. At t
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6083/D6083M − 18 D6083/D6083M − 21
Standard Specification for
Liquid Applied Liquid-Applied Acrylic Coating Used in
1
Roofing
This standard is issued under the fixed designation D6083/D6083M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers liquid-applied water-dispersed acrylic latex elastomeric protective roof coatings.
1.2 This specification does not provide guidance for application.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformancenonconformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C794 Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
D16 Terminology for Paint, Related Coatings, Materials, and Applications
D471 Test Method for Rubber Property—Effect of Liquids
D522/D522M Test Methods for Mandrel Bend Test of Attached Organic Coatings
D562 Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer
D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D903 Test Method for Peel or Stripping Strength of Adhesive Bonds
D1079 Terminology Relating to Roofing and Waterproofing
D1644 Test Methods for Nonvolatile Content of Varnishes
D1653 Test Methods for Water Vapor Transmission of Organic Coating Films
D2196 Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer
1
This test method specification is under the jurisdiction of ASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.09
on Bituminous Emulsions.
Current edition approved Sept. 1, 2018Feb. 15, 2021. Published October 2018February 2021. Originally approved in 1997. Last previous edition approved in 20052018
ɛ1
as D6083 – 05D6083/D6083M – 18. which was withdrawn in 2014 and reinstated in September 2018. DOI: 10.1520/D6083_D6083M-18.DOI: 10.1520/D6083_D6083M-
21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6083/D6083M − 21
D2370 Test Method for Tensile Properties of Organic Coatings
D2697 Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
D4798/D4798M Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc
Method)
G21 Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
3. Terminology
3.1 For definitions of terms used in this specification, see Terminologies D16 and D1079.
4. Classification
4.1 Type I and Type II are defined by the liquid physical properties in Table 1 and cured film physical properties in Table 2.
5. Materials and Manufacture
5.1 Composition—The product, as manufactured, shall be in liquid form for application to the roof surface by brushing,
squeegeeing, rolling, or spraying. The product shall be composed of a water-based acrylic latex elastomeric emulsion polymer, to
which various pigments and other additives have been added to give the required physical properties.
6. Liquid and Cured Film Physical Properties
6.1 Although the product is supplied as a liquid, its performance is based
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.