iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3053-23a

(Terminology)

Standard Terminology Relating to Carbon Black

Standard Terminology Relating to Carbon Black

SCOPE
1.1 This terminology covers a compilation of definitions of technical terms used in the carbon black and rubber industries. Terms that are generally understood or adequately defined in other readily available sources are not included.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
14-Dec-2023
ICS
01.040.83 - Rubber and plastics industries (Vocabularies)
83.040.20 - Rubber compounding ingredients
Technical Committee
D24 - Carbon Black
Drafting Committee
D24.41 - Carbon Black Nomenclature and Terminology
Current Stage
Ref Project

Relations

Replaces
ASTM D3053-23 - Standard Terminology Relating to Carbon Black
Effective Date
15-Dec-2023
Refers
ASTM D3265-24 - Standard Test Method for Carbon Black—Tint Strength
Effective Date
01-Jan-2024
Refers
ASTM D1510-24 - Standard Test Method for Carbon Black—Iodine Adsorption Number
Effective Date
01-Jan-2024
Refers
ASTM D1765-23b - Standard Classification System for Carbon Blacks Used in Rubber Products
Effective Date
15-Dec-2023
Refers
ASTM D3265-23a - Standard Test Method for Carbon Black—Tint Strength
Effective Date
01-Nov-2023
Refers
ASTM D1510-23a - Standard Test Method for Carbon Black—Iodine Adsorption Number
Effective Date
01-Nov-2023
Refers
ASTM D1765-23a - Standard Classification System for Carbon Blacks Used in Rubber Products
Effective Date
01-Apr-2023
Referred By
ASTM D5596-03(2021) - Standard Test Method for Microscopic Evaluation of the Dispersion of Carbon Black in Polyolefin Geosynthetics
Effective Date
15-Dec-2023
Referred By
ASTM D8178-22 - Standard Terminology Relating to Recovered Carbon Black (rCB)
Effective Date
15-Dec-2023
Referred By
ASTM D5817-20 - Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing
Effective Date
15-Dec-2023
Referred By
ASTM D8466-22 - Standard Guide for Recovered Carbon Black—Carbon Black Test Methods for Testing rCB
Effective Date
15-Dec-2023
Referred By
ASTM D6602-13(2022)e1 - Standard Practice for Sampling and Testing of Possible Carbon Black Fugitive Emissions or Other Environmental Particulate, or Both
Effective Date
15-Dec-2023

Buy Standard

ASTM D3053-23a - Standard Terminology Relating to Carbon BlackASTM D3053-23a - Standard Terminology Relating to Carbon Black
PreviousNext
Standard
ASTM D3053-23a - Standard Terminology Relating to Carbon Black
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D3053-23a - Standard Terminology Relating to Carbon BlackREDLINE ASTM D3053-23a - Standard Terminology Relating to Carbon Black
PreviousNext
Standard
REDLINE ASTM D3053-23a - Standard Terminology Relating to Carbon Black
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3053 − 23a
Standard Terminology Relating to
1
Carbon Black
This standard is issued under the fixed designation D3053; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1937 Test Method for Carbon Black, Pelleted—Mass
Strength
1.1 This terminology covers a compilation of definitions of
D2414 Test Method for Carbon Black—Oil Absorption
technical terms used in the carbon black and rubber industries.
Number (OAN)
Terms that are generally understood or adequately defined in
D2663 Test Methods for Carbon Black—Dispersion in Rub-
other readily available sources are not included.
ber
1.2 This international standard was developed in accor-
D3265 Test Method for Carbon Black—Tint Strength
dance with internationally recognized principles on standard-
D3493 Test Method for Carbon Black—Oil Absorption
ization established in the Decision on Principles for the
Number of Compressed Sample (COAN)
Development of International Standards, Guides and Recom-
D3849 Test Method for Carbon Black—Morphological
mendations issued by the World Trade Organization Technical
Characterization of Carbon Black Using Electron Micros-
Barriers to Trade (TBT) Committee.
copy
D5230 Test Method for Carbon Black—Automated Indi-
2. Referenced Documents
vidual Pellet Hardness
2
2.1 ASTM Standards:
D6556 Test Method for Carbon Black—Total and External
D1508 Test Method for Carbon Black, Pelleted Fines and Surface Area by Nitrogen Adsorption
Attrition
D6602 Practice for Sampling and Testing of Possible Carbon
D1509 Test Methods for Carbon Black—Heating Loss Black Fugitive Emissions or Other Environmental
D1510 Test Method for Carbon Black—Iodine Adsorption
Particulate, or Both
Number D7854 Test Method for Carbon Black-Void Volume at Mean
D1511 Test Method for Carbon Black—Pellet Size Distri-
Pressure
bution D8178 Terminology Relating to Recovered Carbon Black
D1513 Test Method for Carbon Black, Pelleted—Pour Den- (rCB)
3
sity 2.2 ISO Standards:
D1514 Test Method for Carbon Black—Sieve Residue
ISO 8887 Technical product documentation — Design for
D1566 Terminology Relating to Rubber manufacturing, assembling, disassembling and end-of-life
D1618 Test Method for Carbon Black Extractables—
processing — Part 1: General concepts and requirements
Transmittance of Toluene Extract ISO 14044 Environmental management – Life cycle assess-
D1765 Classification System for Carbon Blacks Used in
ment – Requirements and guidelines
Rubber Products
3. Terminology
D1799 Practice for Carbon Black—Sampling Packaged
Shipments
3.1 Definitions:
D1900 Practice for Carbon Black—Sampling Bulk Ship-
aciniform, adj—shaped like a cluster of grapes.
ments
DISCUSSION—The spheroidal primary particles of carbon black are
fused into aggregates of colloidal dimension forming an aciniform
morphology.
1
This terminology is under the jurisdiction of ASTM Committee D24 on Carbon carbon black, n—an engineered material, primarily composed
Black and is the direct responsibility of Subcommittee D24.41 on Carbon Black
of elemental carbon, obtained from the partial combustion or
Nomenclature and Terminology.
thermal decomposition of hydrocarbons, existing as aggre-
Current edition approved Dec. 15, 2023. Published January 2024. Originally
gates of aciniform morphology which are composed of
approved in 1972. Last previous edition approved in 2023 as D3053 – 23. DOI:
10.1520/D3053-23A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Available from International Organization for Standardization (ISO), ISO
Standards volume information, refer to the standard’s Document Summary page on Central Secretariat, Chemin de Blandonnet 8, CP 401, 1214 Vernier, Geneva,
the ASTM website. Switzerland, https://www.iso.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3053 − 23a
spheroidal primary particles which exhibit uniformity of carbon black, target value, n—a consensus value for selected
4
primary particle sizes within a given aggregate and tur- primary properties on which producers center their manu-
bostratic layering within the primary particles. facturing process and users center their specification.
DISCUSSION—Carbon black exhibits a hierarchy of morphological DISCUSSION—Target values for carbon
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3053 − 23 D3053 − 23a
Standard Terminology Relating to
1
Carbon Black
This standard is issued under the fixed designation D3053; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This terminology covers a compilation of definitions of technical terms used in the carbon black and rubber industries. Terms
that are generally understood or adequately defined in other readily available sources are not included.
1.2 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1508 Test Method for Carbon Black, Pelleted Fines and Attrition
D1509 Test Methods for Carbon Black—Heating Loss
D1510 Test Method for Carbon Black—Iodine Adsorption Number
D1511 Test Method for Carbon Black—Pellet Size Distribution
D1513 Test Method for Carbon Black, Pelleted—Pour Density
D1514 Test Method for Carbon Black—Sieve Residue
D1566 Terminology Relating to Rubber
D1618 Test Method for Carbon Black Extractables—Transmittance of Toluene Extract
D1765 Classification System for Carbon Blacks Used in Rubber Products
D1799 Practice for Carbon Black—Sampling Packaged Shipments
D1900 Practice for Carbon Black—Sampling Bulk Shipments
D1937 Test Method for Carbon Black, Pelleted—Mass Strength
D2414 Test Method for Carbon Black—Oil Absorption Number (OAN)
D2663 Test Methods for Carbon Black—Dispersion in Rubber
D3265 Test Method for Carbon Black—Tint Strength
D3493 Test Method for Carbon Black—Oil Absorption Number of Compressed Sample (COAN)
D3849 Test Method for Carbon Black—Morphological Characterization of Carbon Black Using Electron Microscopy
D5230 Test Method for Carbon Black—Automated Individual Pellet Hardness
D6556 Test Method for Carbon Black—Total and External Surface Area by Nitrogen Adsorption
D6602 Practice for Sampling and Testing of Possible Carbon Black Fugitive Emissions or Other Environmental Particulate, or
Both
D7854 Test Method for Carbon Black-Void Volume at Mean Pressure
1
This terminology is under the jurisdiction of ASTM Committee D24 on Carbon Black and is the direct responsibility of Subcommittee D24.41 on Carbon Black
Nomenclature and Terminology.
Current edition approved Feb. 1, 2023Dec. 15, 2023. Published February 2023January 2024. Originally approved in 1972. Last previous edition approved in 20222023
as D3053 – 22.D3053 – 23. DOI: 10.1520/D3053-23.10.1520/D3053-23A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3053 − 23a
D8178 Terminology Relating to Recovered Carbon Black (rCB)
3
2.2 ISO Standards:
ISO 8887 Technical product documentation — Design for manufacturing, assembling, disassembling and end-of-life processing
— Part 1: General concepts and requirements
ISO 14044 Environmental management – Life cycle assessment – Requirements and guidelines
3. Terminology
3.1 Definitions:
aciniform, adj—shaped like a cluster of grapes.
DISCUSSION—
The spheroidal primary particles of carbon black are fused into aggregates of colloidal dimension forming an aciniform morphology.
carbon black, n—an engineered material, primarily composed of elemental carbon, obtained from the partial combustion or
thermal decomposition of hydrocarbons, existing as aggregates of aciniform morphology which are composed of spheroidal
4
primary particles which exhibit uniformity of primary particle sizes within a given aggregate and turbostratic layering within
the primary particles.
DISCUSSION—
Carbon black exhibits a hierarchy of morphological features: particles (that is, primary particles), aggregates, and agglomerates. While the fundamental
4
building block of carbon black is the primary particle, they almost never exist in isolation, but are strongly fused by c
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7849-23(Classification)
Standard Classification for Nomenclature of Reference Materials of Committee D24

SIGNIFICANCE AND USE
3.1 Standard reference materials are used for calibration and verification of many carbon black tests under the jurisdiction of D24. This practice defines a systematic means of naming these reference materials and does so in a manner to clearly differentiate between the various reference materials as well as their version.
SCOPE
1.1 This classification covers instructions for naming the reference materials used by Committee D24.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7849-23(Classification)
Standard Classification for Nomenclature of Reference Materials of Committee D24

SIGNIFICANCE AND USE
3.1 Standard reference materials are used for calibration and verification of many carbon black tests under the jurisdiction of D24. This practice defines a systematic means of naming these reference materials and does so in a manner to clearly differentiate between the various reference materials as well as their version.
SCOPE
1.1 This classification covers instructions for naming the reference materials used by Committee D24.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6866-24(Test Method)
Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis

SIGNIFICANCE AND USE
4.1 This testing method provides accurate biobased/biogenic carbon content results to materials whose carbon source was directly in equilibrium with CO2 in the atmosphere at the time of cessation of respiration or metabolism, such as the harvesting of a crop or grass living its natural life in a field. Special considerations are needed to apply the testing method to materials originating from within artificial environments. Application of these testing methods to materials derived from CO2 uptake within artificial environments is beyond the present scope of this standard.  
4.2 Method B utilizes AMS along with Isotope Ratio Mass Spectrometry (IRMS) techniques to quantify the biobased content of a given product. Instrumental error can be within 0.1-0.5 % (1 relative standard deviation (RSD)), but controlled studies identify an inter-laboratory total uncertainty up to ±3 % (absolute). This error is exclusive of indeterminate sources of error in the origin of the biobased content (see Section 22 on precision and bias).  
4.3 Method C uses LSC techniques to quantify the biobased content of a product using sample carbon that has been converted to benzene. This test method determines the biobased content of a sample with a maximum total error of ±3 % (absolute), as does Method B.  
4.4 The test methods described here directly discriminate between product carbon resulting from contemporary carbon input and that derived from fossil-based input. A measurement of a product’s 14C/12C or 14C/13C content is determined relative to a carbon based modern reference material accepted by the radiocarbon dating community such as NIST Standard Reference Material (SRM) 4990C, (referred to as OXII or HOxII). It is compositionally related directly to the original oxalic acid radiocarbon standard SRM 4990B (referred to as OXI or HOxI), and is denoted in terms of fM, that is, the sample’s fraction of modern carbon. (See Terminology, Section 3.)  
4.5 Reference standards, available to all...
SCOPE
1.1 This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical origin, or assignment of required amounts of biobased carbon necessary for compliance with federal laws.  
1.2 These test methods are applicable to any product containing carbon-based components that can be combusted in the presence of oxygen to produce carbon dioxide (CO2) gas. The overall analytical method is also applicable to gaseous samples, including flue gases from electrical utility boilers and waste incinerators.  
1.3 These test methods make no attempt to teach the basic principles of the instrumentation used although minimum requirements for instrument selection are referenced in the References section. However, the preparation of samples for the above test methods is described. No details of instrument operation are included here. These are best obtained from the manufacturer of the specific instrument in use.  
1.4 Limitation—This standard is applicable to laboratories working without exposure to artificial carbon-14 (14C). Artificial 14C is routinely used in biomedical studies by both liquid scintillation counter (LSC) and accelerator mass spectrometry (AMS) laboratories and can exist within the laboratory at levels 1,000 times or more than 100 % biobased materials and 100,000 times more than 1% biobased materials. Once in the laboratory, artificial 14C can become undetectably ubiquitous on door knobs, pens, desk tops, and other surfaces but which may randomly contaminate an unknown sample producing inaccurately high biobased results. Despite vigorous attempts to clean up contaminating artificial 14C from a laboratory, isolation has proven to be the only successful method of avoidance. Completely separate chemical ...

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM F2231-02(2024)(Test Method)
Standard Test Method for Charpy Impact Test on Thin Specimens of Polyethylene Used in Pressurized Pipes

SIGNIFICANCE AND USE
5.1 Brown and Lu4,5 show the Charpy impact energy is related to the ultimate critical temperature of the rapid crack propagation [RCP] behavior as measured by the ISO 13477, S-4 test.6  
5.2 The test method may be used to determine the impact energy of polyethylene used in the manufacture of pipe . This test method involves the preparation of a small compression molded specimen of PE resin that is then notched in a specified manner. The specimen is then broken in a pendulum impact machine. The impact energy is recorded in joules. The value obtained is referred to as the Charpy impact energy.
SCOPE
1.1 This test method describes the specimen preparation and the method of measuring the impact energy of polyethylene used in pressurized pipes.  
1.2 The test specimens are taken from compression molded plaques of the resin from pellets or pipe.  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E3426/E3426M-24(Test Method)
Standard Test Method for Evaluating Aerial Response Robot Endurance

SIGNIFICANCE AND USE
5.1 This test method is part of an overall suite of related test methods that provide repeatable measures of robotic system mobility and remote pilot proficiency. The operational endurance of a robot significantly impacts the performance of the robot during a variety of tasks. Robot endurance is a complex function of robot design, control scheme design, and energy storage selection. This test method evaluates the endurance of a robot through continuous operation. The outdoor and indoor movement tests flight path chosen for endurance testing specifically challenges robotic system locomotion, flight system to maintain position, and remote situational awareness by the remote pilot. As such, it can be used to represent modest outdoor flight or indoor flight within confined areas. The indoor hovering and dwelling tests similarly challenge these capabilities, but for remaining stationary in air within an outdoor or confined indoor area. The endurance test standard provides a method in which the operational endurance of a large variety of robot sizes and locomotion system designs may be compared. The test provides both a measure of the endurance of the robot and a measure of the reliability of the robot when operating continuously for extended periods of time on complex flight paths or continuous use, or both.  
5.2 The indoor tests with containment walls represent repeatable complexity within commercial spaces and residential dwellings with hallways and doorways, or warehouses.  
5.3 The test apparatuses are low-cost and easy to fabricate so they can be widely replicated. The procedure is also simple to conduct. This eases comparisons across various testing locations and dates to determine best-in-class systems and remote pilots.  
5.4 Evaluation—This test method can be used in a controlled environment to measure baseline capabilities. The endurance test apparatus can also be embedded into operational training scenarios to measure degradation due to uncontrolled variab...
SCOPE
1.1 This test method is intended for remotely operated aerial response robots (that is, unmanned aerial systems [UAS], drones, unmanned aircrafts) operating in complex, unstructured, and often hazardous environments. It specifies the apparatuses, procedures, and performance metrics necessary to measure the mission endurance of an aerial robot while either station keeping or following an approximate flight path defined by obstacles or boundaries, or both, intended to induce repeated cyclical movement. This test method is one of several robot tests that can be used to evaluate overall system capabilities.  
1.2 The robotic system includes a remote pilot in control of most functionality, so an onboard camera and remote pilot display are typically required. This test method can be used to evaluate assistive or autonomous behaviors intended to improve the effectiveness or efficiency of remotely operated systems.  
1.3 Different user communities can set their own thresholds of acceptable performance within this test method for various mission requirements.  
1.4 Performing Location—This test method may be performed anywhere the specified apparatuses and environmental conditions can be implemented. Flying unmanned aircraft without a comprehensive understanding of the laws and regulations enforced by the relevant jurisdiction poses significant safety and legal risks. Failure to comply with these regulations may result in accidents, injuries, property damage, and legal consequences. Users of this standard are strongly advised to review and adhere to all applicable ASTM Committee F38 standards and to ensure full compliance with the authorities holding jurisdiction.  
1.5 Units—The International System of Units (SI Units) and U.S. Customary Units (Imperial Units) are used throughout this document. They are not mathematical conversions. Rather, they are approximate equivalents in each system of units to enable use of readily ava...

  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM F714-24(Specification)
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

ABSTRACT
This specification covers polyethylene (PE) pipe made in dimensions based on outside determined range of diameters and larger. The piping is intended for new construction and insertion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpressure systems. Different dimensional properties of pipes like outside diameter, wall thickness, eccentricity, toe-in, and special sizes shall be determined. Physical properties such asdensity, melt index, flexural modulus, tensile strength, slow crack growth resistance, hydrostatic strength, color and UV stabilizer, HDB, and HDS shall determined as well. In order to determine the performance of pipes under pressure the following tests shall be done: short-term pressurization test and elevated temperature sustained pressure test. The pipe shall be homogeneous throughout and essentially uniform in color, opacity, density, and other properties. The inside and outside surfaces shall be semi matte or glossy in appearance (depending on the type of plastic) and free of chalking, sticky, or tacky material. The surfaces shall be free of excessive bloom, that is, slight bloom is acceptable. The pipe walls shall be free of cracks, holes, blisters, voids, foreign inclusion, or other defects that are visible to the naked eye and that may affect the wall integrity. Holes deliberately placed in perforated pipe are acceptable. Bloom or chalking may develop in pipe exposed to direct rays of the sun (ultraviolet radiant energy) for extended periods and, consequently, these requirements do not apply to pipe after extended exposure to direct rays of the sun.
SCOPE
1.1 This specification covers polyethylene (PE) pipe made in three standard outside diameter sizing systems, based on outside diameters of DIPS 3, IPS 4, Metric 90 mm and larger. For smaller sizes refer to Specification D3035. See 5.2.5 for guidelines on special sizes.  
1.2 The piping is intended for new construction and insertion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpressure systems.
Note 1: The user should consult the manufacturer to ensure that any mechanical or chemical effects to the polyethylene pipe caused by the material being transported will not affect the service life beyond limits acceptable to the user. See PPI TR-19 Chemical Resistance of Thermoplastic Piping Materials for guidance on chemical effects, www.plasticpipe.org  
1.3 All pipes produced under this specification are pressure-rated. See Appendix X5 for information on pressure rating.
Note 2: References and material descriptions for PE2406, PE3408 and materials having a HDB of 1450 psi have been removed from Specification F714 due to changes in Specification D3350 and PPI TR-3. For removed designations, refer to previous editions of Specification F714, Specification D3350, PPI TR-3 and PPI TR-4. The removal of these materials does not affect pipelines that are in service. See Note 4 and Note 9.  
1.4 This specification includes criteria for choice of raw material, together with performance requirements and test methods for determining conformance with the requirements.  
1.5 Quality-control measures are to be taken by manufacturers. See Appendix X4 for general information on quality control.  
1.6 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard t...

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F2136-18(2024)(Test Method)
Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe

SIGNIFICANCE AND USE
4.1 This test method does not purport to interpret the data generated.  
4.2 This test method is intended to compare slow-crack-growth (SCG) resistance for a limited set of HDPE resins.  
4.3 This test method may be used on virgin HDPE resin compression-molded into a plaque or on extruded HDPE corrugated pipe that is chopped and compression-molded into a plaque (see 7.1.1 for details).
SCOPE
1.1 This test method is used to determine the susceptibility of high-density polyethylene (HDPE) resins or corrugated pipe to slow-crack-growth under a constant ligament-stress in an accelerating environment. This test method is intended to apply only to HDPE of a limited melt index (0.947 g/cm3 to 0.955 g/cm3). This test method may be applicable for other materials, but data are not available for other materials at this time.  
1.2 This test method measures the failure time associated with a given test specimen at a constant, specified, ligament-stress level.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology D1600, unless otherwise specified.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1503-24(Specification)
Standard Specification for Silvered Flat Glass Mirror

ABSTRACT
This specification covers the requirements for silvered flat glass mirrors of rectangular shape supplied as cut sizes, stock sheets or as lehr ends and to which no further processing (such as edgework or other fabrication) has been done. The quality requirements of silvered annealed monolithic clear and tinted flat glass mirrors up to a certain thickness are also discussed. The mirrors are intended to be used indoors for mirror glazing, for components of decorative accessories or for similar uses. The mirrors are not intended for use in environments where high humidity or airborne corrosion promoters, or both, are consistently present (such as swimming pool areas, ocean-going vessels, chemical laboratories and other corrosive environments). The classification of mirrors are according to the following properties: grades, cut size, stock sheet, lehr end, select quality, glazing quality, color (clear or tinted), and thickness. Different test methods shall be performed in order to determine or measure the following properties: reflectance, silver coating appearance, coating resistance, blemish (point and linear blemishes), dimension, and squareness.
SCOPE
1.1 This specification covers the requirements for silvered flat glass mirrors of rectangular shape supplied as cut sizes, stock sheets, or as lehr ends and to which no further processing (such as edgework or other fabrication) has been done.  
1.2 This specification covers the quality requirements of silvered annealed monolithic clear and tinted flat glass mirrors only, up to 6 mm (1/4 in.) thick. The mirrors are intended to be used indoors for mirror glazing, for components of decorative accessories or for similar uses.  
1.3 This specification does not address safety glazing materials nor requirements for mirror applications. Consult model building codes and other applicable standards for safety glazing applications.  
1.4 Mirrors covered in this specification are not intended for use in environments where high humidity or airborne corrosion promoters, or both, are consistently present (such as swimming pool areas, ocean-going vessels, chemical laboratories, and other corrosive environments).  
1.5 The dimensional values stated in metric units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1044-96(2024)(Specification)
Standard Specification for Glass Serological Pipets (General Purpose and Kahn)

ABSTRACT
This specification covers reusable glass serological pipets used for measuring volumes of liquid. The pipets may be classified into three styles according to operational set-up and should be made with approved glass materials. Each pipet should be straight, of one-piece construction, and properly calibrated. All products should conform to the required dimension of delivery tips, zero gradation line position, dimensions and outflow times, graduation markings, color coding, identification markings, and workmanship.
SCOPE
1.1 This specification covers glass serological pipets, used in measuring volumes of liquids.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2921-98(2024)(Test Method)
Standard Test Method for Qualitative Tests for the Presence of Water Repellents and Preservatives in Wood Products

SIGNIFICANCE AND USE
3.1 Although chlorinated phenol-treated wood has become less common due to environmental concerns, repellent-treated wood is commonly specified in construction. This test method provides a means to verify the presence of a significant level of water repellent protection.
SCOPE
1.1 This test method covers simple qualitative field or laboratory tests to determine water repellency or the presence of chlorinated phenol2 preservative chemicals in wood products that are specified to be water repellent preservative treated.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off