ASTM F2762-11e1

Standard Specification for 12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications (Withdrawn 2016)

SCOPE
1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 12 to 30 in. (300 to 750 mm).  
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.  
1.3 This specification covers pipe and fittings with an interior liner using a corrugated exterior profile (Fig. 1).  
1.4 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 12 to 30 in. (300 to 750 mm).
Formerly under the jurisdiction of Committee F17 on Plastic Piping Systems, this specification was withdrawn in November 2016 and replaced by Specification F2763 for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications.1

General Information

• Status: Withdrawn
• Publication Date: 31-Dec-2010
• ICS: 93.030 - External sewage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Relations

• Replaces: ASTM F2762-11 - Standard Specification for 12 to 30 in. [300 to 750 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• Effective Date: 01-Jan-2011
• Replaced By: ASTM F2763/F2763M-16(2021)e1 - Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
• Effective Date: 04-Nov-2016

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:F2762 −11
StandardSpecification for
12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall
Polyethylene (PE) Pipe and Fittings for Sanitary Sewer
1
Applications
This standard is issued under the fixed designation F2762; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Units statement (1.4) was editorially revised in October 2013.
1. Scope D2122Test Method for Determining Dimensions of Ther-
moplastic Pipe and Fittings
1.1 This specification covers requirements and test methods
D2321PracticeforUndergroundInstallationofThermoplas-
for annular, corrugated profile wall polyethylene pipe and
tic Pipe for Sewers and Other Gravity-Flow Applications
fittings with an interior liner. The nominal inside diameters
D2412Test Method for Determination of External Loading
covered are 12 to 30 in. (300 to 750 mm).
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.2 The requirements of this specification are intended to
D2444Test Method for Determination of the Impact Resis-
provide pipe and fittings suitable for underground use for
tance of Thermoplastic Pipe and Fittings by Means of a
non-pressure sanitary sewer systems. Pipe and fittings pro-
Tup (Falling Weight)
ducedinaccordancewiththisspecificationshallbeinstalledin
D3212Specification for Joints for Drain and Sewer Plastic
compliance with Practice D2321.
Pipes Using Flexible Elastomeric Seals
D3350Specification for Polyethylene Plastics Pipe and Fit-
1.3 This specification covers pipe and fittings with an
interior liner using a corrugated exterior profile (Fig. 1). tings Materials
D4389SpecificationforFinishedGlassFabricsWovenFrom
1.4 Units—The values stated in inch-pound units are to be
Rovings
regarded as standard. The values given in parentheses are
F412Terminology Relating to Plastic Piping Systems
mathematical conversions to SI units that are provided for
F477Specification for Elastomeric Seals (Gaskets) for Join-
information only and are not considered standard.
ing Plastic Pipe
1.5 This standard does not purport to address all of the
F2136Test Method for Notched, Constant Ligament-Stress
safety concerns, if any, associated with its use. It is the
(NCLS) Test to Determine Slow-Crack-Growth Resis-
responsibility of the user of this standard to establish appro-
tance of HDPE Resins or HDPE Corrugated Pipe
priate safety and health practices and determine the applica- 3
2.2 AASHTO Standard:
bility of regulatory limitations prior to use.
LRFD, Section 12AASHTO LRFD Bridge Design Specifi-
cations Section 12 – Buried Structures and Tunnel Liners
4
2. Referenced Documents
2.3 Federal Standard:
2
2.1 ASTM Standards: Fed. Std. No. 123Marking for Shipment (Civil Agencies)
4
A666SpecificationforAnnealedorCold-WorkedAustenitic 2.4 Military Standard:
Stainless Steel Sheet, Strip, Plate, and Flat Bar MIL-STD-129Marking for Shipment and Storage
D618Practice for Conditioning Plastics for Testing
3. Terminology
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
3.1 Definitions—Definitions are in accordance with Termi-
tics
nology F412 and abbreviations are in accordance with Termi-
nologyD1600,unlessotherwisespecified.Theabbreviationfor
polyethylene is PE.
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
3
Current edition approved Jan. 1, 2011. Published January 2011. DOI: 10.1520/ Available from American Association of State Highway and Transportation
F2762–11. Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or http://www.transportation.org.
4
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. dodssp.daps.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
F2762−11
FIG. 1Typical Annular Corrugated Pipe Profile
3.2 Definitions of Terms Specific to This Standard: 6.1.1 Visible defects, cracks, creases, splits, in pipe are not
3.2.1 profile wall, n—In this case, the profile pipe wall permissible.
construction provides an interior liner in the waterway and
6.2 Dimensions and Tolerance:
includesribs,corrugations,orothershapes,whichcanbeeither
6.2.1 Nominal Size—The nominal s
...