iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F3071-14(2020)

(Guide)

Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement

Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to determine a position and collect navigational data in the wilderness. A person trained to this guide shall be endorsed for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW Endorsed).  
4.1.1 Every person who is endorsed for Basic Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is only the first level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to use a GPS/GNSS receiver to determine his or her location and collect navigational data in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Basic Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Basic Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Basic Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the nec...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to determine one’s position, and collect location data, in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 A person who meets the requirements in this guide is only prepared to operate a GPS/GNSS receiver to determine his or her location, and collect position and movement information, in a wilderness environment.  
1.6 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Mar-2020
ICS
33.070.40 - Satellite
Technical Committee
F32 - Search and Rescue
Drafting Committee
F32.03 - Personnel, Training and Education
Current Stage
Ref Project

Relations

Replaces
ASTM F3071-14 - Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement
Effective Date
01-Apr-2020
Refers
ASTM F1773-09(2015) - Standard Terminology Relating to Climbing, Mountaineering, Search and Rescue Equipment and Practices (Withdrawn 2024)
Effective Date
01-Dec-2015
Refers
ASTM F2209-10 - Standard Guide for Training of Level I Land Search Team Member
Effective Date
01-May-2010
Refers
ASTM F1773-09 - Standard Terminology Relating to Climbing, Mountaineering, Search and Rescue Equipment and Practices
Effective Date
01-Oct-2009
Refers
ASTM F1633-97(2008) - Standard Guide for Techniques in Land Search (Withdrawn 2017)
Effective Date
01-Nov-2008
Refers
ASTM F1773-97(2004) - Standard Terminology Relating to Climbing and Mountaineering Equipment and Practices
Effective Date
01-May-2004
Refers
ASTM F1633-97(2003) - Standard Guide for Techniques in Land Search
Effective Date
01-Nov-2003
Refers
ASTM F2209-03 - Standard Guide for Training of Level I Land Search Team Member
Effective Date
10-Apr-2003
Refers
ASTM F1633-97 - Standard Guide for Techniques in Land Search
Effective Date
10-Jul-1997
Refers
ASTM F1773-97 - Standard Terminology Relating to Climbing and Mountaineering Equipment and Practices
Effective Date
01-Jan-1997
Referred By
ASTM F3098-16 - Standard Guide for Training of Non-Wilderness Land Search Team Member
Effective Date
01-Apr-2020
Referred By
ASTM F3175-16 - Standard Guide for Training and Equipping Search and Rescue Personnel Operating on Mountain Bikes (Mountain Bike SAR Endorsement)
Effective Date
01-Apr-2020
Referred By
ASTM F2209-20 - Standard Guide for Training of Land Search Team Member
Effective Date
01-Apr-2020

Buy Standard

ASTM F3071-14(2020) - Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) EndorsementASTM F3071-14(2020) - Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement
PreviousNext
Guide
ASTM F3071-14(2020) - Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F3071 − 14 (Reapproved 2020)
Standard Guide for
Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW)
Endorsement
This standard is issued under the fixed designation F3071; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This guide establishes the minimum knowledge, skills,
and abilities required to use a GPS/GNSS receiver to deter-
2. Referenced Documents
mine one’s position, and collect location data, in the wilder-
2.1 ASTM Standards:
ness.
F1633 Guide for Techniques in Land Search (Withdrawn
1.2 This guide applies to the use of a GPS/GNSS receiver
2017)
on land, on and off roads, and on small bodies of water,
F1773 Terminology Relating to Climbing, Mountaineering,
wherever GPS/GNSS signals can be received.
Search and Rescue Equipment and Practices
1.3 This guide applies to the use of a GPS/GNSS receiver in
F2209 Guide for Training of Land Search Team Member
disasterareaswherelocalpositioningaidsorreferencesmaybe
lost or damaged. 3. Terminology
1.4 This guide does not apply to the use of a GPS/GNSS 3.1 Definitions of Terms Specific to This Standard:
receiver on large bodies of water, at sea, or in the air. 3.1.1 Galileo, n—a GNSS currently under development by
the European Union.
1.5 A person who meets the requirements in this guide is
3.1.2 GLONASS (Globalnaya navigatsionnaya sputnik-
only prepared to operate a GPS/GNSS receiver to determine
ovaya sistema), n—the GNSS owned and operated by the
his or her location, and collect position and movement
Russian Aerospace Defense Forces.
information, in a wilderness environment.
3.1.3 GNSS (Global Navigation Satellite System), n—a
1.6 This guide does not imply that a GPS/GNSS receiver is
navigation system utilizing a constellation of dedicated satel-
a replacement for a map and compass. Use of the latter is
lites to determine a location on or above the earth’s surface.
strongly recommended as a backup for GPS/GNSS navigation.
3.1.4 GNSS receiver, n—a radio receiver that uses satellite
1.7 This standard does not purport to address all of the
signals to fix its location on or above the earth’s surface.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3.1.5 GPS (Global Positioning System), n—the GNSS
priate safety, health, and environmental practices and deter-
owned and operated by the United States government.
mine the applicability of regulatory limitations prior to use.
3.1.6 map datum, n—the set of values used to define a
1.8 This international standard was developed in accor-
particular geodetic model used by a GPS/GNSS receiver to
dance with internationally recognized principles on standard-
determine its location.
ization established in the Decision on Principles for the
3.2 Definitions of terms not defined in this standard can be
Development of International Standards, Guides and Recom-
found inASTM Guide F1633, Guide F1773, and Guide F2209.
4. Significance and Use
This guide is under the jurisdiction of ASTM Committee F32 on Search and
Rescue and is the direct responsibility of Subcommittee F32.03 on Personnel,
4.1 This guide establishes the minimum knowledge, skills,
Training and Education.
andabilitiesrequiredtouseaGPS/GNSSreceivertodetermine
Current edition approved April 1, 2020. Published April 2020. Originally
approved in 2014. Last previous edition approved in 2014 as F3071 – 14. DOI:
10.1520/F3071-14R20.
2 3
This guide refers to GPS/GNSS, rather than GPS, receivers, due to the For referenced ASTM standards, visit the ASTM website, www.astm.org, or
increasing number of global satellite navigation systems worldwide. Currently, only contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
GPS and GLONASS are in operation and provide global satellite coverage. Standards volume information, refer to the standard’s Document Summary page on
However, satellite navigation receivers are now manufactured which are capable of the ASTM website.
utilizing GPS, GLONASS, and Galileo satellites to determine a position on or above The last approved version of this historical standard is referenced on
the earth’s surface. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F3071 − 14 (2020)
a position and collect navigational data in the wilderness. A 5. General Knowledge of a GPS/GNSS Receiver
person trained to this guide shall be endorsed for Basic
5.1 A person endorsed for Basic Wilderness GPS/GNSS
Wilderness GPS/GNSS Use (GPS/GNSS-IW Endorsed).
Use shall demonstrate knowledge of the following:
4.1.1 Every person who is endorsed for Basic Wilderness
5.1.1 How a GPS/GNSS receiver may be used;
GPS
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3072-14(2020)(Guide)
Standard Guide for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to navigate in the wilderness. A person trained to this guide shall be endorsed for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW Endorsed).  
4.1.1 Every person who is endorsed for Intermediate Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is the second level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to navigate with a GPS/GNSS receiver in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Intermediate Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver to navigate in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Intermediate Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Intermediate Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the necessary topics for training a person to be endorsed ...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to navigate in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3072-14(2020)(Guide)
Standard Guide for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to navigate in the wilderness. A person trained to this guide shall be endorsed for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW Endorsed).  
4.1.1 Every person who is endorsed for Intermediate Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is the second level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to navigate with a GPS/GNSS receiver in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Intermediate Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver to navigate in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Intermediate Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Intermediate Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the necessary topics for training a person to be endorsed ...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to navigate in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6152/D6152M-12(2024)(Specification)
Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing

ABSTRACT
This specification covers SEBS (styrene-ethylenebutylene-styrene)-modified mopping asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roofing systems. This specification is intended as a material specification and issues regarding the suitability of specific roof constructions or application techniques are beyond its scope. The specified tests and property values are intended to establish minimum properties. In place system design criteria or performance attributes are factors beyond the scope of this specification. The base asphalt shall be prepared from crude petroleum and the SEBS-modified asphalt shall incorporate sufficient SEBS as the primary polymeric modifier. The SEBS modified asphalt shall be homogeneous and free of water and shall conform to the prescribed physical properties including (1) softening point before and after heat exposure, (2) softening point change, (3) flash point, (4) penetration before and after heat exposure, (5) penetration change, (6) solubility in trichloroethylene, (7) tensile elongation, (8) elastic recovery, and (9) low temperature flexibility. The sampling and test methods to determine compliance with the specified physical properties, as well as the evaluation for stability during heat exposure are detailed.
SCOPE
1.1 This specification covers SEBS (styrene-ethylene-butylene-styrene)-modified asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roof systems.  
1.2 This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond its scope.  
1.3 The specified tests and property values used to characterize SEBS-modified asphalt are intended to establish minimum properties. In-place system design criteria or performance attributes are factors beyond the scope of this specification.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5643/D5643M-06(2024)(Specification)
Standard Specification for Coal Tar Roof Cement, Asbestos Free

ABSTRACT
This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems. The chemical composition of coal tar roof cement shall conform to the requirements prescribed. The water, non-volatile matter, insoluble matter, behaviour at 60 deg. C, adhesion to wet surfaces, and flash point shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D396-24(Specification)
Standard Specification for Fuel Oils

ABSTRACT
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial burners; Grades No. 1 S5000 and No. 1 S500 adapted to vaporizing type burners or where storage conditions require low pour point fuel; Grades No. 4 (Light) and No. 4 (Heavy) for use in commercial/industrial burners; and Grades No. 5 (Light), No. 5 (Heavy), and No. 6 for use in industrial burners. Preheating is usually required for handling and proper atomization. The grades of fuel oil shall be homogeneous hydrocarbon oils, free from inorganic acid, and free from excessive amounts of solid or fibrous foreign matter. Grades containing residual components shall remain uniform in normal storage and not separate by gravity into light and heavy oil components outside the viscosity limits for the grade. The grades of fuel oil shall conform to the limiting requirements prescribed for: (1) flash point, (2) water and sediment, (3) physical distillation or simulated distillation, (4) kinematic viscosity, (5) Ramsbottom carbon residue, (6) ash, (7) sulfur, (8) copper strip corrosion, (9) density, and (10) pour point. The test methods for determining conformance to the specified properties are given.
SCOPE
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows:  
1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2 S15 are middle distillate fuels for use in domestic and small industrial burners. Grades No. 1 S5000, No. 1 S500, and No. 1 S15 are particularly adapted to vaporizing type burners or where storage conditions require low pour point fuel.  
1.1.2 Grades B6–B20 S5000, B6–B20 S500, and B6–B20 S15 are middle distillate fuel/biodiesel blends for use in domestic and small industrial burners.  
1.1.3 Grades No. 4 (Light) and No. 4 are heavy distillate fuels or middle distillate/residual fuel blends used in commercial/industrial burners equipped for this viscosity range.  
1.1.4 Grades No. 5 (Light), No. 5 (Heavy), and No. 6 are residual fuels of increasing viscosity and boiling range, used in industrial burners. Preheating is usually required for handling and proper atomization.  
Note 1: For information on the significance of the terminology and test methods used in this specification, see Appendix X1.
Note 2: A more detailed description of the grades of fuel oils is given in X1.3.  
1.2 This specification is for the use of purchasing agencies in formulating specifications to be included in contracts for purchases of fuel oils and for the guidance of consumers of fuel oils in the selection of the grades most suitable for their needs.  
1.3 Nothing in this specification shall preclude observance of federal, state, or local regulations which can be more restrictive.  
1.4 The values stated in SI units are to be regarded as standard.  
1.4.1 Non-SI units are provided in Table 1 and Table 2 and in 7.1.2.1/7.1.2.2 because these are common units used in the industry.
Note 3: The generation and dissipation of static electricity can create problems in the handling of distillate burner fuel oils. For more information on the subject, see Guide D4865.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    13 pages
    English language
    sale 15% off
  • Technical specification
    13 pages
    English language
    sale 15% off
ASTM
ASTM D8165-24(Test Method)
Standard Test Method for Evaluation of Load-Carrying Capacity of Lubricants Used in Hypoid Final-Drive Axles Operated under Low-Speed and High-Torque Conditions

SIGNIFICANCE AND USE
5.1 This test method measures a lubricant's ability to protect hypoid final drive axles from abrasive wear, adhesive wear, plastic deformation, and surface fatigue when subjected to low-speed, high-torque conditions. Lack of protection can lead to premature gear or bearing failure, or both.  
5.2 This test method is used, or referred to, in specifications and classifications of rear-axle gear lubricants such as:  
5.2.1 Specification D7450.  
5.2.2 American Petroleum Institute (API) Publication 1560.  
5.2.3 SAE J308.  
5.2.4 SAE J2360.
SCOPE
1.1 This test method, commonly referred to as the L-37-1 test, describes a test procedure for evaluating the load-carrying capacity, wear performance, and extreme pressure properties of a gear lubricant in a hypoid axle under conditions of low-speed, high-torque operation.3  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—Where there is no direct SI equivalent such as National Pipe threads/diameters, tubing size, or where there is a sole source supply equipment specification.
1.2.1.1 The drawing in Annex A6 is in inch-pound units.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 7.2 and 10.1.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D6416/D6416M-16(2024)(Test Method)
Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load

SIGNIFICANCE AND USE
5.1 This test method simulates the hydrostatic loading conditions which are often present in actual sandwich structures, such as marine hulls. This test method can be used to compare the two-dimensional flexural stiffness of a sandwich composite made with different combinations of materials or with different fabrication processes. Since it is based on distributed loading rather than concentrated loading, it may also provide more realistic information on the failure mechanisms of sandwich structures loaded in a similar manner. Test data should be useful for design and engineering, material specification, quality assurance, and process development. In addition, data from this test method would be useful in refining predictive mathematical models or computer code for use as structural design tools. Properties that may be obtained from this test method include:  
5.1.1 Panel surface deflection at load,  
5.1.2 Panel face-sheet strain at load,  
5.1.3 Panel bending stiffness,  
5.1.4 Panel shear stiffness,  
5.1.5 Panel strength, and  
5.1.6 Panel failure modes.
SCOPE
1.1 This test method determines the two-dimensional flexural properties of sandwich composite plates subjected to a distributed load. The test fixture uses a relatively large square panel sample which is simply supported all around and has the distributed load provided by a water-filled bladder. This type of loading differs from the procedure of Test Method C393, where concentrated loads induce one-dimensional, simple bending in beam specimens.  
1.2 This test method is applicable to composite structures of the sandwich type which involve a relatively thick layer of core material bonded on both faces with an adhesive to thin-face sheets composed of a denser, higher-modulus material, typically, a polymer matrix reinforced with high-modulus fibers.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D3019/D3019M-17(2024)(Specification)
Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, and Fibered

ABSTRACT
This specification covers the physical requirements and testing of three types of lap cement for use with asphalt roll roofing. Type I is a brushing consistency lap cement intended for use in the exposed-nailing method of roll roofing application, and contains no mineral or other stabilizers. This type is further divided into two grades, as follows: Grade 1, which is made with an air-blown asphalt; and Grade 2, which is made with a vacuum-reduced or steam-refined asphalt. Both Types II and III, on the other hand, are heavy brushing or light troweling consistency lap cement intended for use in the concealed-nailing method of roll roofing application, only that Type II cement contains a quantity of short-fibered asbestos, while Type III cement contains a quantity of mineral or other stabilizers, or both, but contains no asbestos. The lap cements shall be sampled for testing, and shall adhere to specified values of the following properties: water content; distillation (total distillate at given temperatures); softening point of residue; solubility in trichloroethylene; and strength at indicated age.
SCOPE
1.1 This specification covers lap cement consisting of asphalt dissolved in a volatile petroleum solvent with or without mineral or other stabilizers, or both, for use with roll roofing. The fibered version of these cements excludes the use of asbestos fibers.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 The following precautionary caveat applies only to the test method portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4586/D4586M-07(2024)(Specification)
Standard Specification for Asphalt Roof Cement, Asbestos-Free

ABSTRACT
This specification covers the testing and requirements for two types and two classes of asbestos-free asphalt roof cement consisting of an asphalt base, volatile petroleum solvents, and mineral and/or other stabilizers, mixed to a smooth, uniform consistency suitable for trowel application to roofing and flashing. Type I is made from asphalts characterized as self-healing, adhesive, and ductile, while Type II is made from asphalt characterized by high softening point and relatively low ductility. Class I is used for application to essentially dry surfaces, while Class II is used for application to damp, wet, or underwater surfaces. The roof cements shall comply with composition limits for water, nonvolatile matter, mineral and/or other stabilizers, and bitumen (asphalt). They shall also meet physical requirements such as uniformity, workability, and pliability and behavior at given temperatures.
SCOPE
1.1 This specification covers asbestos-free asphalt roof cement suitable for trowel application to roofings and flashings.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 8 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM C1178/C1178M-24(Specification)
Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel

ABSTRACT
This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile. Coated glass mat water-resistant gypsum backing panel shall consist of a noncombustible water-resistant gypsum core, surfaced with glass mat, partially or completely embedded in the core, and with a water-resistant coating on one surface. The specimens shall be tested for flexural strength, humidified deflection, core hardness, end hardness, edge hardness, nail pull resistance, water resistance, and surface water absorption. Coated glass mat water-resistant gypsum backing panel shall have surfaces true and free of imperfections that render the panel unfit for its designed use.
SCOPE
1.1 This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off