EN 13391:2004

Mechanical tests for post-tensioning systems

This European Standard specifies the test procedures for the anchorages and couplings of post-tensioning systems. This standard is to be used in conjunction with the relevant European Standards ENV 1992-1-1 and ENV 1992-2 and others for pertaining to prestressed concrete structures.
The test results should be used for the acquisition of the Technical Approval of the specified post-tensioning system.
For unbonded tendons additional tests and requirements are needed and these are not covered in the present scope of this standard.

Mechanische Prüfungen für Spannverfahren it nachträglichem Verbund

Diese Europäische Norm legt Prüfverfahren für und Anforderungen an Verankerungen und Kopplungen der Spannglieder von Vorspannverfahren mit nachträglichem Verbund fest. Sie ist zusammen mit folgenden Europäischen Normen sowie weiteren einschlägigen Normen anzuwenden: prEN 10138-1 bis -5, ENV 1992-1-1 und ENV 1992-2. Als Kriterium für die bauliche Zulassung des jeweiligen Vorspannsystems mit nachträglichem Verbund sollten die Ergebnisse der beschriebenen Prüfungen zusammen mit den Ergebnissen folgender ergänzender Untersuchungen verwendet werden.

Essais mécaniques concernant les procédés de précontrainte par post-tension

Cette Norme Européenne spécifie les procédures d'essai et les exigences auxquelles doivent satisfaire les résultats des essais sur les ancrages et coupleurs des procédés de précontrainte par post-tension. Cette norme doit être utilisée conjointement avec les Normes Européennes correspondantes prEN 10138, ENV 1992 1.1. et ENV 1992.2, ainsi que d'autres concernant les structures en béton précontraint. Les résultats d'essai doivent être utilisés en vue de l'obtention de l'agrément technique du procédé de précontrainte par post-tension spécifié, concurremment avec les résultats d'examens complémentaires.

Mehanski preskusi za ponapenjalne sisteme

General Information

• Status: Published
• Publication Date: 09-Mar-2004
• Withdrawal Date: 29-Sep-2004
• ICS: 91.080.40 - Concrete structures
• Technical Committee: CEN/TC 250 - Structural Eurocodes
• Drafting Committee: CEN/TC 250/SC 2 - Eurocode 2: Design of concrete structures
• Current Stage: 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
• Start Date: 04-Jun-2023
• Completion Date: 04-Jun-2023
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN 13391:2004 - Mechanical tests for post-tensioning systems

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mehanski preskusi za ponapenjalne sistemeMechanische Prüfungen für Spannverfahren it nachträglichem VerbundEssais mécaniques concernant les procédés de précontrainte par post-tensionMechanical tests for post-tensioning systems91.080.40Betonske konstrukcijeConcrete structures19.060Mehansko preskušanjeMechanical testingICS:Ta slovenski standard je istoveten z:EN 13391:2004SIST EN 13391:2004en01-september-2004SIST EN 13391:2004SLOVENSKI
STANDARD



SIST EN 13391:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13391March 2004ICS 91.080.40English versionMechanical tests for post-tensioning systemsEssais mécaniques concernant les procédés deprécontrainte par post-tensionMechanische Prüfungen für Spannverfahren itnachträglichem VerbundThis European Standard was approved by CEN on 3 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13391:2004: ESIST EN 13391:2004



EN 13391:2004 (E)2ContentsPageForeword.31Scope.42Normative references.43Terms, definitions and symbols.43.1Definitions.44Tests and requirements for post-tensioning anchorages.64.1General.64.1.1Purpose.64.1.2Specification of system.64.1.3Laboratory, testing facility.64.1.4Materials and components for the tests.64.1.5Types of test.64.2Testing of systems with mechanical anchorages.74.2.1Static load test with tendon-anchorage assembly.74.2.2Fatigue test with tendon-anchorage assembly.94.2.3Load transfer test.104.3Testing of systems with bond anchorage.114.3.1Static load test with bond anchorage.114.3.2Fatigue load test with bond anchorage.125Supplementary tests.
...