EN ISO 5456-3:1999
(Main)Technical drawings - Projection methods - Part 3: Axonometric representations (ISO 5456-3:1996)
Technical drawings - Projection methods - Part 3: Axonometric representations (ISO 5456-3:1996)
Technische Zeichnungen - Projektionsmethoden - Teil 3: Axonometrische Darstellungen (ISO 5456-3:1996)
Dieser Teil von ISO 5456 legt die Grundregeln für die Anwendung von empfohlenen axonometrischen Darstellungen für alle Arten von technischen Zeichnungen fest.
Dessins techniques - Méthodes de projection - Partie 3: Représentations axonométriques (ISO 5456-3:1996)
Gradbeniške risbe - Metode projekcije - 3. del: Aksonometrijske predstavitve (ISO 5456-3:1996)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2002
Gradbeniške risbe - Metode projekcije - 3. del: Aksonometrijske predstavitve (ISO
5456-3:1996)
Technical drawings - Projection methods - Part 3: Axonometric representations (ISO
5456-3:1996)
Technische Zeichnungen - Projektionsmethoden - Teil 3: Axonometrische Darstellungen
(ISO 5456-3:1996)
Dessins techniques - Méthodes de projection - Partie 3: Représentations
axonométriques (ISO 5456-3:1996)
Ta slovenski standard je istoveten z: EN ISO 5456-3:1999
ICS:
01.100.01 7HKQLþQRULVDQMHQDVSORãQR Technical drawings in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL
STANDARD
First edition
1996-06-I 5
Technical drawings - Projection methods -
Part 3:
Axonometric representations
Methodes de projection -
Dessins techniques -
Partie 3: Rep&en ta tions axonomb triques
Reference number
IS0 5456-3: %996(E)
IS0 5456-3: 1996(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work of
preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be rep-
resented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 5456-3 was prepared by Technical Committee
ISOnC 10, Technical drawings, product definition and related documen-
tation, Subcommittee SC 1, Basic conventions.
IS0 5456 consists of the following parts, under the general title Technical
drawings - Projection methods:
- Part 1: Synopsis
Part 2: Orthographic representations
Part 3: Axonome tric representations
Part 4: Central projection
Annex A of this part of IS0 5456 is for information only.
0 IS0 1996
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 l CH-121 1 Geneve 20 l Switzerland
Printed in Switzerland
ii
@ IS0 IS0 5456-3: 1996(E)
Introduction
Axonometric representations are simple pictorial representations obtained
by projecting the object to be represented from an infinitely distant point
(projection centre) on a single projection plane (normally the drawing sur-
face). This kind of parallel projection gives an adequate approximation for
distant views.
The resulting representation depends on the shape of the object and on
the relative positions of the projection centre, the projection plane and the
object itself.
Among the infinite possibilities of axonometric representation, only a few
types are recommended for technical drawings in all fields of technical
activities (mechanical, electrical, construction, etc.).
Axonometric representations are not as commonly used in technical
drawings as are orthographic representations.
This page intentionally left blank
INTERNATIONAL STANDARD @ IS0 IS0 5456-3: 1996(E)
Projection methods -
Technical drawings -
Part 3:
Axonometric representations
IS0 10209-Z: 1993, Technical product documentation
1 Scope
- Vocabulary - Part 2: Terms relating to projection
This part of IS0 5456 specifies basic rules for the methods.
application of the recommended axonometric rep-
resentations for all types of technical drawings.
3 Definitions
2 Normative references
For the purposes of this part of IS0 5456, the defi-
nitions given in IS0 5456-1, IS0 10209-I and
The following standards contain provisions which,
IS0 10209-Z apply.
through reference in this text, constitute provisions of
this part of IS0 5456. At the time of publication, the
editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this
4 General
part of IS0 5456 are encouraged to investigate the
possibility of applying the most recent editions of the
The general principles of presentation given in
standards indicated below. Members of IEC and IS0
IS0 128 shall be followed.
maintain registers of currently valid International
Standards.
IS0 128: 1982, Technical drawings - General prin- 4.1 Position of the coordinate system
ciples of presentation.
The position of the coordinate axes shall be chosen,
IS0 129:1985, Technical drawings - Dimensioning -
by convention, so that one of the coordinate axes (the
General principles, definitions, methods of execution
Z-axis) is vertical.
and special indications.
IS0 3098-I :I 974, Technical drawings - Lettering -
4.2 Position of the object
Part 7: Currently used characters.
The object to be represented is located with its prin-
IS0 5456-l : 1996, Technical drawings - Projection
cipal faces, axes and edges parallel to the coordinate
methods - Part 7: Synopsis.
planes. The object shall be orientated to show the
principal view and the other views that would prefer-
IS0 10209-I : 1992, Technical product documentation
Part 7: Terms relating to technical ably be chosen when representing the same object in
- Vocabulary -
orthogonal projections.
drawings
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.