iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

CEN ISO/TR 16060:2014

(Main)

Destructive tests on welds in metallic materials - Etchants for macroscopic and microscopic examination (ISO/TR 16060:2003)

Destructive tests on welds in metallic materials - Etchants for macroscopic and microscopic examination (ISO/TR 16060:2003)

ISO/TR 16060:2003 gives a non-exhaustive list of etchants that can be used for the macroscopic and microscopic examination of welds in accordance with ISO 17639 for the following groups of materials:
carbon steels and low-alloy steels;stainless steels;nickel and nickel alloys;titanium and titanium alloys;copper and copper alloys;aluminium and aluminium alloys.

Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Ätzungen für die makroskopische und mikroskopische Untersuchung (ISO/TR 16060:2003)

Dieser Technische Bericht enthält eine keinesfalls vollständige Liste von Ätzmitteln, die für die makroskopischen und mikroskopischen Untersuchungen von Schweißnähten in Übereinstimmung mit ISO 17639 für die folgenden Werkstoffgruppen verwendet werden können:
-   Kohlenstoff- und niedriglegierte Stähle;
-   nichtrostende Stähle;
-   Nickel und Nickellegierungen;
-   Titan und Titanlegierungen;
-   Kupfer und Kupferlegierungen;
-   Aluminium und Aluminiumlegierungen.

Essais destructifs des soudures sur matériaux métalliques - Réactifs pour examens macroscopique et microscopique (ISO/TR 16060:2003)

L'ISO/TR 16060:2003 donne une liste non exhaustive des réactifs pouvant être utilisés pour l'examen macroscopique et microscopique des soudures conformément à l'ISO 17639 pour les groupes de matériaux suivants:
aciers non alliés et faiblement alliés; aciers inoxydables; nickel et alliages de nickel; titane et alliages de titane; cuivre et alliages de cuivre; aluminium et alliages d'aluminium.

Porušitvene preiskave zvarov na kovinskih materialih - Jedkala za makroskopsko in mikroskopsko preiskavo (ISO/TR 16060:2003)

Standard ISO/TR 16060 podaja neizčrpen seznam jedkal, ki jih je mogoče uporabiti za makroskopsko in mikroskopsko preiskavo zvarov v skladu s standardom ISO 17639 za naslednje skupine materialov: – ogljikova jekla in malolegirana jekla; – nerjavna jekla; – nikelj in nikljeve zlitine; – titan in titanove zlitine; – baker in bakrove zlitine; – aluminij in aluminijeve zlitine.

General Information

Status
Published
Publication Date
12-Aug-2014
ICS
25.160.40 - Welded joints and welds
Technical Committee
CEN/TC 121 - Welding
Drafting Committee
CEN/TC 121 - Welding
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
13-Aug-2014
Due Date
20-Oct-2015
Completion Date
13-Aug-2014
Ref Project
SIST-TP CEN ISO/TR 16060:2014 - Destructive tests on welds in metallic materials - Etchants for macroscopic and microscopic examination (ISO/TR 16060:2003)

Relations

Replaces
CR 12361:1996/AC:1997 - Destructive tests on welds in metallic materials - Etchants for macroscopic and microscopic examination
Effective Date
20-Aug-2014
Replaces
CR 12361:1996 - Destructive tests on welds in metallic materials - Etchants for macroscopic and microscopic examination
Effective Date
22-Jan-2014

Buy Standard

TP CEN ISO/TR 16060:2014TP CEN ISO/TR 16060:2014
PreviousNext
Technical report
TP CEN ISO/TR 16060:2014
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TP CEN ISO/TR 16060:2014
01-november-2014
1DGRPHãþD
SIST CR 12361:1999
SIST CR 12361:1999/AC:1999
Porušitvene preiskave zvarov na kovinskih materialih - Jedkala za makroskopsko
in mikroskopsko preiskavo (ISO/TR 16060:2003)
Destructive tests on welds in metallic materials - Etchants for macroscopic and
microscopic examination (ISO/TR 16060:2003)
Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Ätzungen
für die makroskopische und mikroskopische Untersuchung (ISO/TR 16060:2003)
Essais destructifs des soudures sur matériaux métalliques - Réactifs pour examens
macroscopique et microscopique (ISO/TR 16060:2003)
Ta slovenski standard je istoveten z: CEN ISO/TR 16060:2014
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST-TP CEN ISO/TR 16060:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP CEN ISO/TR 16060:2014

---------------------- Page: 2 ----------------------

SIST-TP CEN ISO/TR 16060:2014

TECHNICAL REPORT
CEN ISO/TR 16060

RAPPORT TECHNIQUE

TECHNISCHER BERICHT
August 2014
ICS 25.160.40 Supersedes CR 12361:1996
English Version
Destructive tests on welds in metallic materials - Etchants for
macroscopic and microscopic examination (ISO/TR 16060:2003)
Essais destructifs des soudures sur matériaux métalliques - Zerstörende Prüfung von Schweißverbindungen an
Réactifs pour examens macroscopique et microscopique metallischen Werkstoffen - Ätzungen für die
(ISO/TR 16060:2003) makroskopische und mikroskopische Untersuchung
(ISO/TR 16060:2003)


This Technical Report was approved by CEN on 18 August 2014. It has been drawn up by the Technical Committee CEN/TC 121.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TR 16060:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TP CEN ISO/TR 16060:2014
CEN ISO/TR 16060:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST-TP CEN ISO/TR 16060:2014
CEN ISO/TR 16060:2014 (E)
Foreword
The text of ISO/TR 16060:2003 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as CEN
ISO/TR 16060:2014 by Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of
which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CR 12361:1996.
Endorsement notice
The text of ISO/TR 16060:2003 has been approved by CEN as CEN ISO/TR 16060:2014 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST-TP CEN ISO/TR 16060:2014

---------------------- Page: 6 ----------------------

SIST-TP CEN ISO/TR 16060:2014

TECHNICAL ISO/TR
REPORT 16060
First edition
2003-10-15

Destructive tests on welds in metallic
materials — Etchants for macroscopic
and microscopic examination
Essais destructifs des soudures sur matériaux métalliques — Réactifs
pour examens macroscopique et microscopique




Reference number
ISO/TR 16060:2003(E)
©
ISO 2003

---------------------- Page: 7 ----------------------

SIST-TP CEN ISO/TR 16060:2014
ISO/TR 16060:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 9692-2:2024(Main)
Welding and allied processes - Joint preparation - Part 2: Submerged arc welding of steels (ISO 9692-2:2024)
oSIST prEN ISO 9692-2:2023

This document applies to types of joint preparation for submerged arc welding with one wire electrode (process 121 according to ISO 4063) on steel.
This document covers only the welding positions PA and PB according to ISO 6947. If PC is used, special preparation is necessary.
This document applies to fully penetrated welds. For partly penetrated welds, types of joint preparation, shapes and dimensions can differ from the listed proposals if they are specified in the relevant application standard or agreed by the parties concerned.

  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5817:2023(Main)
Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2023)
SIST EN ISO 5817:2023

This document specifies quality levels of imperfections in fusion-welded joints (except for beam welding) in all types of steel, nickel, titanium and their alloys. It applies to material thickness ≥ 0,5 mm. It covers fully penetrated butt welds and all fillet welds. Its principles can also be applied to partial-penetration butt welds.
Quality levels for beam-welded joints in steel are presented in ISO 13919-1.
Three quality levels are given in order to permit application to a wide range of welded fabrication. They are designated by symbols B, C and D. Quality level B corresponds to the highest requirement on the finished weld.
Several types of loads are considered, e.g. static load, thermal load, corrosion load, pressure load. Additional guidance on fatigue loads is given in Annex B.
The quality levels refer to production and good workmanship.
This document is applicable to:
a)       non-alloy and alloy steels;
b)       nickel and nickel alloys;
c)        titanium and titanium alloys;
d)       manual, mechanized and automatic welding;
e)       all welding positions;
f)         all types of welds, e.g. butt welds, fillet welds and branch connections;
g)       the following welding processes and their sub-processes, as defined in ISO 4063:
—     11 metal arc welding without gas protection;
—     12 submerged arc welding;
—     13 gas-shielded metal arc welding;
—     14 gas-shielded arc welding with non-consumable tungsten electrode;
—     15 plasma arc welding;
—     31 oxyfuel gas welding (for steel only).
Metallurgical aspects, such as grain size and hardness, are not covered by this document.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 5173:2023(Main)
Destructive tests on welds in metallic materials - Bend tests (ISO 5173:2023)
SIST EN ISO 5173:2023

This document specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt welds with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to reveal imperfections on or near the surface of the test specimen which is under tension during bend testing and/or assess ductility. It also gives the dimensions of the test specimen.
In addition, this document specifies methods to be used instead of transverse bend tests with a former for welded joints when base materials, heat affected zones and/or weld metal have a significant difference in their physical and mechanical properties in relation to bending.
This document applies to metallic materials in all forms of product with welded joints made by any welding process.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4761:2022(Main)
Non-destructive testing of welds - Phased array ultrasonic testing (UT-PA) for thin-walled steel components - Acceptance levels (ISO 4761:2022)
SIST EN ISO 4761:2023

This document specifies acceptance levels for the phased array ultrasonic testing technique (UT-PA) of full-penetration welds in low-alloy and/or fine-grained steels in the wall thickness range from 3,2 mm to 8 mm which correspond to the quality levels of ISO 5817.
These acceptance levels are applicable to indications detected according to ISO 20601.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10447:2022(Main)
Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2022)
SIST EN ISO 10447:2023

This document specifies the procedures and recommended tooling to be used for peel and chisel testing of resistance spot and embossed projection welds. This document applies to welds made in two or more sheets in the thickness range of 0,5 mm to 3,0 mm.
The aim of these tests is to determine:
—    weld size and failure mode when welds are destructively tested;
—    verification of welds by non-destructive chisel tests.
NOTE      The preferred method of peel testing seam welds (mechanized peel testing) is covered in ISO 14270.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17636-2:2022(Main)
Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2022, Corrected version 2023-02)
SIST EN ISO 17636-2:2023

This document specifies techniques of digital radiography with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject.
This document applies to the digital radiographic testing of fusion welded joints in metallic materials. It applies to the joints of plates and pipes. Besides its conventional meaning, “pipe”, as used in this document, covers other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels.
This document specifies the requirements for digital radiographic X- and gamma-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDAs) of the welded joints of metallic plates and tubes for the detection of imperfections. It includes manual and automated inspection with DDAs.
Digital detectors provide a digital grey value image which can be viewed and evaluated using a computer (Annex E). This document specifies the recommended procedure for detector selection and radiographic practice. Selection of computer, software, monitor, printer and viewing conditions are important, but are not the main focus of this document. The procedure specified in this document provides the minimum requirements for radiographic practice which permits exposure and acquisition of digital radiographs with equivalent sensitivity for the detection of imperfections as film radiography (specified in ISO 17636-1).
This document does not specify acceptance levels for any of the indications found on the digital radiographs. ISO 10675 provides information on acceptance levels for weld inspection.
If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17636-1:2022(Main)
Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2022)
SIST EN ISO 17636-1:2023

This document specifies techniques of radiographic testing of fusion-welded joints in metallic materials using industrial radiographic film techniques with the object of enabling satisfactory and repeatable results. The techniques are based on generally recognized practice and fundamental theory of the subject.
It applies to the joints of plates and pipes in metallic materials. Besides its conventional meaning, “pipe” as used in this document covers other cylindrical bodies, such as tubes, penstocks, boiler drums and pressure vessels.
This document does not specify acceptance levels for any of the indications found on the radiographs. The ISO 10675 series provides information on acceptance levels for weld evaluation.
If contracting parties apply lower test criteria, it is possible that the quality achieved will be significantly lower than when this document is strictly applied.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4136:2022(Main)
Destructive tests on welds in metallic materials - Transverse tensile test (ISO 4136:2022)
SIST EN ISO 4136:2022

This document specifies the sizes of test specimen and the procedure for carrying out transverse tensile tests in order to determine the tensile strength and the location of fracture of a welded butt joint.
This document applies to metallic materials in all forms of product with joints made by any welded butt joint.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9016:2022(Main)
Destructive tests on welds in metallic materials - Impact tests - Test specimen location, notch orientation and examination (ISO 9016:2022)
SIST EN ISO 9016:2022

This document specifies the method to be used when describing test specimen location and notch orientation for the testing and reporting of impact tests on welded butt joints.
This document applies to impact tests on metallic materials in all forms of product made by any fusion and pressure welding process.
It is used in addition to the ISO 148 series and includes test specimen denomination and additional reporting requirements.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17639:2022(Main)
Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2022)
SIST EN ISO 17639:2022

This document gives recommendations for specimen preparation, test procedures and their main objectives for macroscopic and microscopic examination.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day