EN ISO 10855-2:2024
(Main)Offshore containers and associated lifting sets - Part 2: Design, manufacture and marking of lifting sets (ISO 10855-2:2024)
Offshore containers and associated lifting sets - Part 2: Design, manufacture and marking of lifting sets (ISO 10855-2:2024)
This document specifies requirements for lifting sets for use with containers in offshore service, including technical requirements, marking and statements of conformity for single and multi-leg slings, including chain slings and wire rope slings.
Offshore-Container und dazugehörige Anschlaggarnituren - Teil 2: Auslegung, Herstellung und Kennzeichnung von Anschlaggarnituren (ISO 10855-2:2024)
Dieses Dokument legt Anforderungen für Anschlaggarnituren zur Verwendung mit Containern im Offshore-Betrieb fest, einschließlich technischen Anforderungen und Anforderungen an die Kennzeichnung sowie Konformitätserklärungen für einsträngige und mehrsträngige Anschlagmittel, einschließlich Anschlagketten und Anschlagdrahtseilen.
Conteneurs pour une utilisation en mer et dispositifs de levage associés - Partie 2: Conception, fabrication et marquage des dispositifs de levage associés (ISO 10855-2:2024)
Le présent document spécifie les exigences relatives aux dispositifs de levage destinés à être utilisés avec des conteneurs offshore de service, y compris les exigences techniques, le marquage et les déclarations de conformité des élingues simples et des élingues multi-brins, comprenant les élingues en chaînes et les élingues de câbles en acier.
Plavajoče kontejnerske enote in z njimi povezan dvižni pribor - 2. del: Načrtovanje, izdelava in označevanje dvižnih priborov (ISO 10855-2:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 10855-2:2024
01-april-2024
Plavajoče kontejnerske enote in z njimi povezan dvižni pribor - 2. del: Načrtovanje,
izdelava in označevanje dvižnih priborov (ISO/DIS 10855-2:2024)
Offshore containers and associated lifting sets - Part 2: Design, manufacture and
marking of lifting sets (ISO/DIS 10855-2:2024)
Offshore-Container und dazugehörige Anschlaggarnituren - Teil 2: Auslegung,
Herstellung und Kennzeichnung von Anschlaggarnituren (ISO/DIS 10855-2:2024)
Conteneurs offshore et dispositifs de levage associés - Partie 2: Conception, fabrication
et marquage des dispositifs de levage associés (ISO/DIS 10855-2:2024)
Ta slovenski standard je istoveten z: prEN ISO 10855-2
ICS:
53.020.99 Druga dvigalna oprema Other lifting equipment
55.180.10 Večnamenski kontejnerji General purpose containers
75.180.10 Oprema za raziskovanje, Exploratory, drilling and
vrtanje in odkopavanje extraction equipment
oSIST prEN ISO 10855-2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 10855-2:2024
oSIST prEN ISO 10855-2:2024
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10855-2
ISO/TC 67/SC 7 Secretariat: BSI
Voting begins on: Voting terminates on:
2024-02-01 2024-04-25
Offshore containers and associated lifting sets —
Part 2:
Design, manufacture and marking of lifting sets
Conteneurs offshore et dispositifs de levage associés —
Partie 2: Conception, fabrication et marquage des dispositifs de levage associés
ICS: 75.180.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10855-2:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024
oSIST prEN ISO 10855-2:2024
ISO/DIS 10855-2:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10855-2
ISO/TC 67/SC 7 Secretariat: BSI
Voting begins on: Voting terminates on:
Offshore containers and associated lifting sets —
Part 2:
Design, manufacture and marking of lifting sets
Conteneurs offshore et dispositifs de levage associés —
Partie 2: Conception, fabrication et marquage des dispositifs de levage associés
ICS: 75.180.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 10855-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 10855-2:2024
ISO/DIS 10855-2:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Technical requirements . 2
5.1 General requirements . 2
5.2 Dimensions and strength of lifting sets . 3
5.3 Chain slings . . 3
5.4 Wire rope slings. 3
5.5 Shackles . 4
5.6 Materials . 4
5.6.1 Impact testing . 4
5.6.2 Hardness testing. 4
5.6.3 Welding . 4
5.6.4 Materials used in wire rope slings . 5
5.6.5 Corrosion protection . 5
5.6.6 Material certificates . 5
6 Certificates .5
6.1 Preparation of certificates . 5
6.2 Single component certificates . 5
6.3 Sling certificates. 5
7 Marking . . 6
Annex A (normative) Determination of minimum required working load limit (WLL ) of
min
the lifting set . 8
Annex B (informative) Example of identification tag for chain slings .10
Annex C (informative) Regulations for offshore containers .12
Bibliography .14
iii
oSIST prEN ISO 10855-2:2024
ISO/DIS 10855-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the WTO principles
in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.
A list of all the parts of ISO 10855 can be found on the ISO website.
iv
oSIST prEN ISO 10855-2:2024
ISO/DIS 10855-2:2023(E)
Introduction
[10]
ISO 10855 (all parts) meets the requirements of IMO MSC/Circ.860 for the design, construction,
inspection, testing and in-service examination of offshore containers and the associated lifting sets
which are handled in open seas.
This document does not specify certification requirements for offshore containers which are covered
by the IMO Circular 860 and SOLAS. IMO MSC/Circ.860 requires certification of offshore containers
“by national administrations or organizations duly authorized by the Administration”, which should
take account of both the calculations and the testing, “taking into account the dynamic lifting and
impact forces that can occur when handling such equipment in open seas”. Further information about
certification can be found in informative Annex C of this document.
ISO 10855 (all parts) does not cover operational use or maintenance, for which there are several
industry guidelines which can be referred to. Some are listed in the bibliography.
Under conditions in which offshore containers are often transported and handled, the 'normal' rate of
wear and tear is high, and damage necessitating repair will occur. However, containers designed and
manufactured according to ISO 10855 (all parts) will have sufficient strength to withstand the normal
forces encountered in offshore operations, and not suffer complete failure even if subject to more
extreme loads.
v
oSIST prEN ISO 10855-2:2024
oSIST prEN ISO 10855-2:2024
DRAFT INTERNATIONAL STANDARD ISO/DIS 10855-2:2023(E)
Offshore containers and associated lifting sets —
Part 2:
Design, manufacture and marking of lifting sets
1 Scope
This document specifies requirements for lifting sets for use with containers in offshore service,
including technical requirements, marking and statements of conformity for single and multi-leg slings,
including chain slings and wire rope slings.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 148-1, Metallic materials — Charpy
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.