iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 15551-1:2015

(Main)

Petroleum and natural gas industries - Drilling and production equipment - Part 1: Electric submersible pump systems for artificial lift (ISO 15551-1:2015)

Petroleum and natural gas industries - Drilling and production equipment - Part 1: Electric submersible pump systems for artificial lift (ISO 15551-1:2015)

ISO 15551-1:2015 provides requirements for the design, design verification and validation, manufacturing and data control, performance ratings, functional evaluations, handling, and storage of tubing-deployed electrical submersible pump (ESP) systems as defined herein. This part of ISO 15551 is applicable to those components meeting the definition of centrifugal pumps including gas handling devices, discharge heads, seal chamber sections, intake systems, mechanical gas separators, induction motors (herein motor), shaft couplings, motor lead extension, pothead, and power cables, as defined herein. Components supplied under the requirements of this part of ISO 15551 exclude previously used subcomponents. Additionally, this International Standard provides requirements for assembled ESP systems.
ISO 15551-1:2015 includes normative annexes addressing design validation performance rating requirements by component, requirements for determining ratings as an assembled system, functional evaluation: single component and cable reference information.
ISO 15551-1:2015 includes informative annexes addressing functional evaluation guidelines for assembled ESP systems, establishing recommended operating range (ROR) of the ESP system, example user/purchaser ESP functional specification form, considerations for the use of 3-phase low and medium voltage adjustable speed drives for ESP applications, analysis after ESP use, downhole monitoring of ESP assembly operation, and information on permanent magnet motors for ESP applications.
Equipment not covered by this part of ISO 15551 includes wireline and coiled tubing-deployed ESP systems, motor and pump shrouds, electric penetrators and feed-through systems, cable clamps and banding, centralizers, intake screens, passive gas separators, by-pass tools, check and bleeder valves, component adaptors, capillary lines, electric surface equipment, downhole permanent magnet motors, and non-conventionally configured ESP systems such as inverted systems. Repair and redress equipment requirements are not covered in this part of ISO 15551.
The terminologies used within this part of ISO 15551 are; "ESP assembly" for a system of products combined into an operational machine, "component" for individual products such as, pumps or seal chamber sections, and "subcomponent" for individual parts or subassemblies that are used in the construction of an individual component.

Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstungen - Teil 1: Elektrische Tauchpumpen zur Förderung (ISO 15551-1:2015)

Industries du pétrole et du gaz naturel - Équipement de forage et de production - Partie 1: Systèmes électriques de pompes submersibles pour l'ascension artificielle (ISO 15551-1:2015)

Industrija za predelavo nafte in zemeljskega plina - Proizvodna oprema za vrtanje - 1. del: Električne potopne črpalke za prečrpavanje na površino (ISO 15551-1:2015)

General Information

Status
Withdrawn
Publication Date
12-May-2015
Withdrawal Date
03-Oct-2023
ICS
75.180.10 - Exploratory, drilling and extraction equipment
Technical Committee
CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
Drafting Committee
CEN/TC 12 - Materials, equipment and offshore structures for petroleum and natural gas industries
Current Stage
Ref Project
SIST EN ISO 15551-1:2015 - Petroleum and natural gas industries - Drilling and production equipment - Part 1: Electric submersible pump systems for artificial lift (ISO 15551-1:2015)

Relations

Replaced By
EN ISO 15551:2023 - Petroleum and natural gas industries - Drilling and production equipment - Electric submersible pump systems for artificial lift (ISO 15551:2023)
Effective Date
18-Jan-2023

Buy Standard

EN ISO 15551-1:2015EN ISO 15551-1:2015
PreviousNext
Standard
EN ISO 15551-1:2015
English language
131 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15551-1:2015
01-julij-2015
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD3URL]YRGQDRSUHPD]DYUWDQMH
GHO(OHNWULþQHSRWRSQHþUSDONH]DSUHþUSDYDQMHQDSRYUãLQR ,62
Petroleum and natural gas industries - Drilling and production equipment - Part 1:
Electric submersible pump systems for artificial lift (ISO 15551-1:2015)
Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstungen - Teil 1: Elektrische Tauchpumpen
zur Förderung (ISO 15551-1:2015)
Industries du pétrole et du gaz naturel - Équipement de forage et de production - Partie
1: Systèmes électriques de pompes submersibles pour l'ascension artificielle (ISO 15551
-1:2015)
Ta slovenski standard je istoveten z: EN ISO 15551-1:2015
ICS:
23.080 ýUSDONH Pumps
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
SIST EN ISO 15551-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15551-1:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 15551-1:2015

EUROPEAN STANDARD
EN ISO 15551-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2015
ICS 75.180.10
English Version
Petroleum and natural gas industries - Drilling and production
equipment - Part 1: Electric submersible pump systems for
artificial lift (ISO 15551-1:2015)
Industries du pétrole et du gaz naturel - Équipement de Erdöl- und Erdgasindustrie - Bohrloch-Ausrüstungen - Teil
forage et de production - Partie 1: Systèmes électriques de 1: Elektrische Tauchpumpen zur Förderung (ISO 15551-
pompes submersibles pour l'ascension artificielle (ISO 1:2015)
15551-1:2015)
This European Standard was approved by CEN on 5 March 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15551-1:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15551-1:2015
EN ISO 15551-1:2015 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15551-1:2015
EN ISO 15551-1:2015 (E)
Foreword
This document (EN ISO 15551-1:2015) has been prepared by Technical Committee ISO/TC 67 “Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries” in collaboration
with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2015, and conflicting national standards shall be withdrawn
at the latest by November 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13702:2024(Main)
Oil and gas industries - Control and mitigation of fires and explosions on offshore production installations - Requirements and guidelines (ISO 13702:2024)
kSIST FprEN ISO 13702:2024

This document specifies the objectives and functional requirements for the control and mitigation of fires and explosions on offshore installations used for the development of hydrocarbon resources in oil and gas industries. The object is to achieve:
safety of personnel;
protection of the environment;
protection of assets;
minimization of financial and consequential losses of fires and explosions.
This document is applicable to the following:
fixed offshore structures;
floating systems for production, storage, and offloading.
Mobile offshore units and subsea installations are excluded, although many of the principles contained in this document can be used as guidance.

  • Draft
    72 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19901-3:2024(Main)
Oil and gas industries including lower carbon energy - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2024)
SIST EN ISO 19901-3:2024

This document provides requirements, guidance and information for the design and fabrication of topsides structure for offshore structures, including in-service, pre-service and post-service conditions.
The actions on topsides structure and the action effects in structural components are derived from this document, where necessary in combination with other International Standards in the ISO 19901 series (e.g. ISO 19901-1 for wind actions - see 7.6.2, ISO 19901-2 for seismic actions - see 7.7) and ISO 19902 for fatigue design (see 6.7).
This document is applicable to the following:
—     topsides of fixed offshore structures;
—     discrete structural units placed on the hull structures of floating offshore structures and mobile offshore units;
—     topsides of arctic offshore structures, excluding winterization (see ISO 19906).
If any part of the topsides structure forms part of the primary structure of the overall structural system which resists global platform actions, the requirements of this document are supplemented with applicable requirements in ISO 19902, ISO 19903, ISO 19904-1, ISO 19905-1, ISO 19905-3 and ISO 19906.
For those parts of floating offshore structures and mobile offshore units that are chosen to be governed by the rules of a recognized classification society, the corresponding class rules supersede the associated requirements of this document.
This document also addresses prevention, control and assessment of fire, explosions and other accidental events.
The fire and explosion provisions of this document can be applied to those parts of the hulls of floating structures and mobile offshore units that contain hydrocarbon processing, piping or storage.
NOTE          Requirements for structural integrity management are presented in ISO 19901-9.
This document applies to structural components including the following:
—     primary and secondary structure in decks, module support frames and modules;
—     flare structures;
—     crane pedestal and other crane support arrangements;
—     helicopter landing decks (helidecks);
—     permanent bridges between separate offshore structures;
—     masts, towers and booms on offshore structures.
This document provides requirements for selecting and using a national building standard with a correspondence factor for determining the resistance of rolled and welded non-circular prismatic components and their connections.

  • Standard
    164 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19905-1:2023(Main)
Oil and gas industries including lower carbon energy - Site-specific assessment of mobile offshore units - Part 1: Jack-ups: elevated at a site (ISO 19905-1:2023)
SIST EN ISO 19905-1:2024

This document specifies requirements and provides recommendation and guidance for the elevated site-specific assessment (SSA-E) of independent leg jack‑up units for use in the petroleum and natural gas industries. It addresses:
a)       occupied non-evacuated, occupied evacuated and unoccupied jack‑ups;
b)       the installed (or elevated) phase at a specific site.
It also addresses the requirement that the as-installed condition matches the assumptions used in the assessment.
This document does not address the site-specific assessment of installation and removal (SSA-I).
To ensure acceptable reliability, the provisions of this document form an integrated approach, which is used in its entirety for the site-specific assessment of a jack‑up.
When assessing a jack-up operating in regions subject to sea ice and icebergs, it is intended that the assessor supplements the provisions of this document with the relevant provisions relating to ice actions contained in ISO 19906 and procedures for ice management contained in ISO 35104. This document does not address design, transit to and from site, or installation and removal from site.
This document is applicable only to independent leg mobile jack-up units that are structurally sound and adequately maintained, which is normally demonstrated through holding a valid recognized classification society, classification certificate. Jack‑ups that do not hold a valid recognized classification society certificate are assessed according to the provisions of ISO 19902, supplemented by methodologies from this document, where applicable.
NOTE 1        Well conductors can be a safety-critical element for jack‑up operations. However, the integrity of well conductors is not part of the site-specific assessment process for jack‑ups and is, therefore, not addressed in this document. See A.1 for guidance on this topic.
NOTE 2        RCS rules and the IMO MODU code (International Maritime Organisation Mobile Offshore Drilling Unit code) provide guidance for the design of jack-ups.

  • Standard
    384 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13703-2:2023(Main)
Oil and gas industries including lower carbon energy - Piping systems on offshore platforms and onshore plants - Part 2: Materials (ISO 13703-2:2023)
SIST EN ISO 13703-2:2023

This document provides a set of unified requirements and specifications regarding material quality level and pre-qualification for piping material of seamless pipes, welded pipes, wrought fittings, plates, forgings, bars, castings and piping bolts/nuts used for piping systems in the oil and gas industry, both offshore and onshore.
This document covers the following material grades:
-   C-Mn steel;
-   high strength steel;
-   austenitic stainless steels;
-   duplex stainless steels;
-   nickel alloy;
-   Cu-Ni alloy;
-   titanium alloy;
-   Cu-alloy.

  • Standard
    320 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12736-1:2023(Main)
Oil and gas industries including lower carbon energy - Wet thermal insulation systems for pipelines and subsea equipment - Part 1: Validation of materials and insulation systems (ISO 12736-1:2023)
SIST EN ISO 12736-1:2023

This document specifies requirements for the validation of wet thermal insulation systems applied to
pipelines and subsea equipment in the oil and gas industry.
This document is applicable to wet thermal insulation systems submerged in seawater.
This document is not applicable to:
— maintenance works on existing installed wet thermal insulation systems;
— qualification for anti-corrosion coating;
— thermal insulation in the annulus of a steel pipe-in-pipe system.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12736-2:2023(Main)
Oil and gas industries including lower carbon energy - Wet thermal insulation systems for pipelines and subsea equipment - Part 2: Qualification processes for production and application procedures (ISO 12736-2:2023)
SIST EN ISO 12736-2:2023

This document specifies requirements for project specific product and process qualification of wet
thermal insulation systems applied to pipelines in a factory setting and subsea equipment in the oil and
gas industries.
This document is not applicable to:
— pre-fabricated insulation;
— thermal insulation in the annulus of a steel pipe-in-pipe system;
— maintenance works on existing installed wet thermal insulation systems;
— project qualification of anticorrosion coatings or the requirements for application thereof.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12736-3:2023(Main)
Oil and gas industries including lower carbon energy - Wet thermal insulation systems for pipelines and subsea equipment - Part 3: Interfaces between systems, field joint system, field repairs and prefabricated insulation (ISO 12736-3:2023)
SIST EN ISO 12736-3:2023

This document specifies requirements for project specific product and process qualification of field
applied wet thermal insulation systems applied at interfaces (e.g. field joints) and pre-fabricated
insulation in the petroleum and natural gas industries.
This document is applicable to wet thermal insulation systems submerged in seawater.
This document is not applicable to:
— the project qualification of anticorrosion coatings or the requirements for application thereof;
— thermal insulation in the annulus of a steel pipe-in-pipe system.

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13703-3:2023(Main)
Oil and gas industries including lower carbon energy - Piping systems on offshore production platforms and onshore plants - Part 3: Fabrication (ISO 13703-3:2023)
SIST EN ISO 13703-3:2023

This document defines requirements for the fabrication, welding, examination and testing of new, metallic piping systems up to 69 000 kPa (ga) maximum, within temperature range limits for the materials meeting the requirements of ASME B31.3, on fixed and floating offshore production facilities and onshore production, processing and liquefaction plants.
This document is applicable to all pressure retaining components and any non-pressure retaining component, such as a pipe support, welded directly to a pressure retaining component.
This document is not applicable to:
- marine-related piping systems, e.g. ballasting piping systems, systems covered by classification societies;
- non-metallic piping systems.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15551:2023(Main)
Petroleum and natural gas industries - Drilling and production equipment - Electric submersible pump systems for artificial lift (ISO 15551:2023)
SIST EN ISO 15551:2023

This document specifies requirements for the design, design verification and validation, manufacturing and data control, performance ratings, functional evaluations, handling and storage of tubing-deployed electrical submersible pump (ESP) systems. Additionally, this document provides requirements for assembled ESP system.
This document is applicable to those ESP related components meeting the definition of centrifugal pumps, including gas handling devices, discharge heads, seal chamber sections, intake systems, mechanical gas separators, asynchronous 3 phase - 2 pole induction motors (herein motor), shaft couplings, downhole power cables (herein power cables), motor lead extension, and pothead. Components supplied under the requirements of this document exclude previously used subcomponents, except where the use of such subcomponents is as defined in this document (Clause 9).
This document addresses design validation performance rating requirements by component (see Annex A), requirements for determining ratings as an assembled system (see Annex B), functional evaluation: single component (see Annex C) and cable reference information (see Annex D).
This document addresses functional evaluation guidelines for assembled ESP systems, establishing recommended operating range (ROR) of the ESP system (see Annex F), example user/purchaser ESP functional specification form (see Annex G), considerations for the use of 3-phase low and medium voltage adjustable speed drives for ESP applications (see Annex H), analysis after ESP use (see Annex I), downhole monitoring of ESP assembly operation (see Annex J), information on permanent magnet motors for ESP applications (see Annex K) and users guide (see Annex L).
This document also includes a user guide that offers a high-level process workflow when applying this document.
This document does not apply to: wireline and coiled tubing-deployed ESP systems, motor shrouds and pump shrouds, electric penetrators and feed-through systems, cable clamps and banding, centralizers, intake screens, passive gas separators, by-pass tools, check and bleeder valves, component adaptors, capillary lines, electric surface control equipment, downhole permanent magnet motors and non-conventionally configured ESP systems such as inverted systems. This document does not apply to Repair and redress equipment requirements.

  • Standard
    144 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 19901-8:2023(Main)
Oil and gas industries including lower carbon energy - Offshore structures - Part 8: Marine soil investigations (ISO 19901-8:2023)
SIST EN ISO 19901-8:2023

This document specifies requirements and provides recommendations and guidelines for marine soil investigations regarding:
a)    objectives, planning and execution of marine soil investigations;
b)    deployment of investigation equipment;
c)    drilling and logging;
d)    in situ testing;
e)    sampling;
f)     laboratory testing;
g)    reporting.
Although this document focuses on investigations of soil, it also provides guidance, with less detail, for investigations of chalk, calcareous soils, cemented soils and weak rock.
Foundation design is not covered by this document.
NOTE 1    ISO 19901‑4 and the respective design standards covering foundation design for the specific types of offshore structures to meet the requirements of application specific standards are given on the ISO website.
The results from marine geophysical investigations are, when available and where appropriate, used for planning, optimization and interpretation of marine soil investigations.
This document neither covers the planning, execution and interpretation of marine geophysical investigations nor the planning and scope of geohazard assessment studies, only the corresponding marine soil investigations aspects thereof.
NOTE 2    ISO 19901-10 covers the planning, execution and interpretation of marine geophysical investigations.
This document specifies requirements and provides guidance for obtaining measured values and derived values. This document excludes requirements for determination of design values and representative values. Limited guidance is provided in 11.3 related to data interpretation.
This document is intended for clients, soil investigation contractors, designers, installation contractors, geotechnical laboratories and public and regulatory authorities concerned with marine soil investigations for any type of offshore structures, or geohazard assessment studies.

  • Standard
    164 pages
    English language
    sale 10% off
    e-Library read for
    1 day