Hardmetals - Metallographic determination of microstructure - Part 3: Measurement of microstructural features in Ti (C, N) and WC/cubic carbide based hardmetals (ISO 4499-3:2016)

ISO 4499-3:2016 gives guidelines for the measurement of microstructural features in Ti(C,N) based hardmetals and WC/Co hardmetals that contain additional cubic carbides by metallographic techniques only using optical or electron microscopy. It is intended for sintered hardmetals (also called cemented carbides or cermets) containing primarily inorganic carbides and nitrides as the hard phase. It is also intended for measuring the phase size and distribution by the linear intercept technique.

Hartmetalle - Metallographische Bestimmung der Mikrostruktur - Teil 3: Messung von mikrostrukturellen Merkmalen in Hartmetallen auf Basis von Ti (C, N) und WC/kubischem Carbid (ISO 4499-3:2016)

Métaux-durs - Détermination métallographique de la microstructure - Partie 3: Mesure des caractéristiques des microstructures des métaux-durs à base de carbures Ti (C, N) et WC/cubiques (ISO 4499-3:2016)

L'ISO 4499-3:2016 donne des lignes directrices relatives à la mesure des caractéristiques des microstructures des métaux-durs à base de carbures Ti(C,N) et de métaux-durs WC/Co contenant des carbures cubiques supplémentaires selon des techniques métallographiques utilisant uniquement un microscope optique ou électronique. Elle est destinée aux métaux-durs frittés (également appelés carbures cémentés ou cermets) contenant principalement des carbures et nitrures inorganiques sous la forme d'une phase dure. Elle est également destinée au mesurage de la taille des phases et de la distribution au moyen de la technique d'interception linéaire.

Trdine - Metalografsko določevanje mikrostrukture - 3. del: Merjenje mikrostrukturnih značilnosti v trdinah na osnovi Ti (C, N) in WC/kubičnega karbida (ISO 4499-3:2016)

Ta del standarda ISO 4499 podaja navodila za merjenje mikrostrukturnih značilnosti v trdinah na osnovi Ti (C, N) in WC/kubičnega karbida, ki vsebujejo dodatne kubične karbide, na podlagi metalografskih tehnik, ki uporabljajo le optično mikroskopijo ali mikroskopijo elektronov. Uporablja se za sintrane trdine (imenovane tudi cementirani karbidi ali cermeti), ki v trdi fazi vsebujejo pretežno anorganske karbide in nitride. Namenjen je tudi merjenju velikosti in distribucije faze s tehniko linearnega prestrezanja.

General Information

Status
Published
Publication Date
15-Mar-2016
Withdrawal Date
29-Sep-2016
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
16-Mar-2016
Completion Date
16-Mar-2016

Buy Standard

Standard
EN ISO 4499-3:2016 - BARVE
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 4499-3:2014 - BARVE
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4499-3:2016
01-maj-2016
7UGLQH0HWDORJUDIVNRGRORþHYDQMHPLNURVWUXNWXUHGHO0HUMHQMH
PLNURVWUXNWXUQLK]QDþLOQRVWLYWUGLQDKQDRVQRYL7L &1 LQ:&NXELþQHJDNDUELGD
,62
Hardmetals - Metallographic determination of microstructure - Part 3: Measurement of
microstructural features in Ti (C, N) and WC/cubic carbide based hardmetals (ISO 4499-
3:2016)
Hartmetalle - Metallographische Bestimmung der Mikrostruktur - Teil 3: Messung von
mikrostrukturellen Merkmalen in Hartmetallen auf Basis von Ti (C, N) und WC/kubischem
Carbid (ISO 4499-3:2016)
Métaux-durs - Détermination métallographique de la microstructure - Partie 3: Mesure
des caractéristiques des microstructures des métaux-durs à base de carbures Ti (C, N)
et WC/cubiques (ISO 4499-3:2016)
Ta slovenski standard je istoveten z: EN ISO 4499-3:2016
ICS:
77.040.99 Druge metode za Other methods of testing of
preskušanje kovin metals
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 4499-3:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4499-3:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 4499-3:2016


EN ISO 4499-3
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2016
EUROPÄISCHE NORM
ICS 77.040.99; 77.160
English Version

Hardmetals - Metallographic determination of
microstructure - Part 3: Measurement of microstructural
features in Ti (C, N) and WC/cubic carbide based
hardmetals (ISO 4499-3:2016)
Métaux-durs - Détermination métallographique de la Hartmetalle - Metallographische Bestimmung der
microstructure - Partie 3: Mesure des caractéristiques Mikrostruktur - Teil 3: Messung von
des microstructures des métaux-durs à base de mikrostrukturellen Merkmalen in Hartmetallen auf
carbures Ti (C, N) et WC/cubiques (ISO 4499-3:2016) Basis von Ti (C, N) und WC/kubischem Carbid (ISO
4499-3:2016)
This European Standard was approved by CEN on 4 February 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4499-3:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 4499-3:2016
EN ISO 4499-3:2016 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 4499-3:2016
EN ISO 4499-3:2016 (E)
European foreword
This document (EN ISO 4499-3:2016) has been prepared by Technical Committee ISO/TC 119 "Powder
metallurgy".
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2016, and conflicting national standards
shall be withdrawn at the latest by September 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turke
...

SLOVENSKI STANDARD
oSIST prEN ISO 4499-3:2014
01-maj-2014
7UGLQH0HWDORJUDIVNRGRORþHYDQMHPLNURVWUXNWXUHGHO0HUMHQMH
PLNURVWUXNWXUQLK]QDþLOQRVWLYWUGLQDKQDRVQRYL7L &1 LQ:&NXELþQHJDNDUELGD
,62',6
Hardmetals - Metallographic determination of microstructure - Part 3: Measurement of
microstructural features in Ti (C, N) and WC/Cubic Carbide Based Hardmetals (ISO/DIS
4499-3:2014)
Hartmetalle - Metallographische Bestimmung der Mikrostruktur - Teil 3: Messung von
mikrostrukturellen Merkmalen in Hartmetallen auf Basis von Ti (C, N) und WC/kubischem
Carbid (ISO/DIS 4499-3:2014)
Métaux-durs - Détermination métallographique de la microstructure - Partie 3: Mesure
des caractéristiques des microstructures des métaux-durs à base de carbures Ti (C, N)
et WC/cubiques (ISO/DIS 4499-3:2014)
Ta slovenski standard je istoveten z: prEN ISO 4499-3
ICS:
77.040.99 Druge metode za Other methods of testing of
preskušanje kovin metals
77.160 Metalurgija prahov Powder metallurgy
oSIST prEN ISO 4499-3:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 4499-3:2014

---------------------- Page: 2 ----------------------
oSIST prEN ISO 4499-3:2014
DRAFT INTERNATIONAL STANDARD
ISO/DIS 4499-3
ISO/TC 119/SC 4 Secretariat: DIN
Voting begins on: Voting terminates on:
2014-03-13 2014-08-13
Hardmetals — Metallographic determination of
microstructure —
Part 3:
Measurement of microstructural features in Ti (C, N) and
WC/Cubic Carbide Based Hardmetals
Métaux-durs — Détermination métallographique de la microstructure —
Partie 3: Mesure des caractéristiques des microstructures des métaux-durs à base de carbures Ti (C, N) et
WC/cubiques
ICS: 77.040.99;77.160
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 4499-3:2014(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2014

---------------------- Page: 3 ----------------------
oSIST prEN ISO 4499-3:2014
ISO/DIS 4499-3:2014(E)

Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2014 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 4499-3:2014
ISO/DIS 4499-3
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.