Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2022)

This document specifies the characteristics of hexagon head screws, in steel and stainless steel, with metric coarse pitch threads M1,6 to M64, and with product grades A and B.
If in certain cases other specifications are requested, property classes and stainless steel grades can be selected from ISO 898-1 or ISO 3506-1, and dimensional options from ISO 888 or ISO 4753.

Verbindungselemente - Sechskantschrauben mit Gewinde bis Kopf - Produktklassen A und B (ISO 4017:2022)

Dieses Dokument legt Eigenschaften von Sechskantschrauben mit Gewinde bis Kopf aus Stahl und nichtrostendem Stahl mit metrischen Regelgewinden von M1,6 bis M64 in Produktklasse A und Produktklasse B fest.
Falls in bestimmten Fällen andere Festlegungen benötigt werden, können Festigkeitsklassen sowie Stahlsorten nichtrostender Stähle aus ISO 898 1 oder ISO 3506 1 und maßliche Alternativen aus ISO 888 oder ISO 4753 entnommen werden.

Fixations - Vis à tête hexagonale entièrement filetées - Grades A et B (ISO 4017:2022)

Le présent document spécifie les caractéristiques des vis à tête hexagonale entièrement filetées, en acier et en acier inoxydable, à filetage métrique à pas gros M1,6 à M64, et de grades A et B.
Si dans certains cas d’autres spécifications sont requises, les classes de qualité et les grades d’acier inoxydable peuvent être choisis dans l'ISO 898‑1 ou l'ISO 3506‑1, et les options dimensionnelles dans l'ISO 888 ou l'ISO 4753.

Vezni elementi - Vijaki s šestrobo glavo z navojem do glave - Razreda izdelave A in B (ISO 4017:2022)

Ta dokument določa značilnosti vijakov s šestrobo glavo z navojem do glave iz jekla in nerjavnega jekla, z
grobim metričnim navojem velikosti M1,6 do M64 in razredoma izdelave A in B.
Če se v določenih primerih zahtevajo druge specifikacije, je razrede lastnosti in tipe nerjavnega jekla mogoče izbrati po standardih ISO 898-1 ali ISO 3506-1, dimenzijske možnosti pa po ISO 888 ali ISO 4753.

General Information

Status
Published
Publication Date
19-Jul-2022
Withdrawal Date
30-Jan-2023
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Jul-2022
Completion Date
20-Jul-2022

Relations

Buy Standard

Standard
EN ISO 4017:2022
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN ISO 4017:2014
Vezni elementi - Vijaki s šestrobo glavo z navojem do glave - Razreda izdelave A in
B (ISO 4017:2022)
Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2022)
Sechskantschrauben mit Gewinde bis Kopf - Produktklassen A und B (ISO 4017:2022)
Fixations - Vis à tête hexagonale entièrement filetées - Grades A et B (ISO 4017:2022)
Ta slovenski standard je istoveten z: EN ISO 4017:2022
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 4017
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2022
EUROPÄISCHE NORM
ICS 21.060.10 Supersedes EN ISO 4017:2014
English Version
Fasteners - Hexagon head screws - Product grades A and B
(ISO 4017:2022)
Fixations - Vis à tête hexagonale entièrement filetées - Sechskantschrauben mit Gewinde bis Kopf -
Grades A et B (ISO 4017:2022) Produktklassen A und B (ISO 4017:2022)
This European Standard was approved by CEN on 25 September 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4017:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 4017:2022) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2023, and conflicting national standards shall
be withdrawn at the latest by January 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4017:2014.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 4017:2022 has been approved by CEN as EN ISO 4017:2022 without any modification.

INTERNATIONAL ISO
STANDARD 4017
Sixth edition
2022-06
Fasteners — Hexagon head screws —
Product grades A and B
Fixations — Vis à tête hexagonale entièrement filetées — Grades A et
B
Reference number
ISO 4017:2022(E)
ISO 4017:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 4017:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions .2
5 Requirements and reference International Standards . 7
6 Marking and labelling . 8
6.1 Marking on product . . 8
6.2 Labelling on package . 8
7 Designation . 8
Annex A (normative) Dimensions for screws M1,6 to M14 with product grade B .9
Bibliography .11
iii
ISO 4017:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 11,
Fasteners with metric external thread, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 185, Fasteners, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This sixth edition cancels and replaces the fifth edition (ISO 4017:2014), which has been technically
revised.
The main changes are as follows:
— tables for dimensions have been entirely restructured, so that the user can find the specified values
in a reliable manner (no risk of picking the wrong dimension), see Clause 4 and Annex A;
— M7 has been added;
— d has been changed for sizes d ≤ M5 from s – IT16 to s – IT15, in order to have a larger
w,min min min
bearing surface area and thus less contact pressure;
— greatest standard lengths (accidentally removed in the fifth edition) have been restored, rules for
the shortest and greatest standard lengths have been added, and amended accordingly;
— for steel screws, property classes 4.8 and 12.9/12.9 have been added;
— for stainless steel screws, grades D4 and D6 and property class 80 have been added;
— property class 9.8 and non-ferrous metal screws have been deleted;
— specifications for marking and labelling have been added as Clause 6.
Any feedback or questions on this document should be directed to the user's national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 4017:2022(E)
Fasteners — Hexagon head screws — Product grades A and
B
1 Scope
This document specifies the characteristics of hexagon head screws, in steel and stainless steel, with
metric coarse pitch threads M1,6 to M64, and with product grades A and B.
If in certain cases other specifications are requested, property classes and stainless steel grades can be
selected from ISO 898-1 or ISO 3506-1, and dimensional options from ISO 888 or ISO 4753.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 225, Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
ISO 888, Fasteners — Bolts, screws and studs — Nominal lengths and thread lengths
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs with specified property classes — Coarse thread and fine pitch thread
ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 1891-4, Fasteners — Vocabulary — Part 4: Control, inspection, delivery, acceptance and quality
ISO 3269, Fasteners — Acceptance inspection
ISO 3506-1, Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1:
Bolts, screws and studs with specified grades and property classes
ISO 4042, Fasteners — Electroplated coating systems
ISO 4753, Fasteners — Ends of parts with external ISO metric thread
ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1, Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
ISO 6157-3, Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements
ISO 8991, Designation system for fasteners
ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts
ISO 10683, Fasteners — Non-electrolytically applied zinc flake coating systems
ISO 10684, Fasteners — Hot dip galvanized coatings
3 Terms and definitions
No terms and definitions are listed in this document.
ISO 4017:2022(E)
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Dimensions
Dimensions shall be in accordance with Figures 1 and 2 and with Tables 1 to 4.
Symbols and descriptions of dimensions are defined in ISO 225.

a
In accord
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.